Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 12-04-2020, 05:44 PM   #1
Ben38
Member
 
Ben38's Avatar
 
Join Date: May 2010
Location: Apple Valley, MN
Posts: 61
Default Soldering iron

I need to replace the wires going to my horns and horn relay but my Weller gun doesn’t have enough wattage to melt the old solder joints. What wattage irons do you guys use for these joints?
Thanks
Ben38 is offline   Reply With Quote
Old 12-04-2020, 05:51 PM   #2
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Soldering iron

Quote:
Originally Posted by Ben38 View Post
I need to replace the wires going to my horns and horn relay but my Weller gun doesn’t have enough wattage to melt the old solder joints. What wattage irons do you guys use for these joints?
Thanks
I have noticed that it takes a bit longer to melt those old solder joints. I too use a Weller gun. It happens but takes a bit longer than "normal".
Patience my friend, patience
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 12-04-2020, 06:02 PM   #3
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Soldering iron

This will do it in a heartbeat.
https://www.ebay.com/itm/300W-110V-S...EAAOSwbWpec7Z0
19Fordy is offline   Reply With Quote
Old 12-04-2020, 06:20 PM   #4
Ironrod
Member
 
Ironrod's Avatar
 
Join Date: Jun 2010
Location: Utica, KY
Posts: 81
Default Re: Soldering iron

If space allows, I use a micro torch, Carefully.
https://www.harborfreight.com/butane...kaAh9HEALw_wcB
Ironrod is offline   Reply With Quote
Old 12-04-2020, 07:17 PM   #5
50fordcoupeman
Senior Member
 
50fordcoupeman's Avatar
 
Join Date: Mar 2016
Location: LaGrande Oregon
Posts: 865
Default Re: Soldering iron

Quote:
Originally Posted by Ben38 View Post
I need to replace the wires going to my horns and horn relay but my Weller gun doesn’t have enough wattage to melt the old solder joints. What wattage irons do you guys use for these joints?
Thanks
My gun was not heating up enough either and thought it had gone gunny sack. What happened is that the screws that hold the tip in place had loosened up. I retightened them and it works perfectly again......almost threw away a perfectly good soldering iron!
50fordcoupeman is offline   Reply With Quote
Old 12-04-2020, 08:54 PM   #6
Ben38
Member
 
Ben38's Avatar
 
Join Date: May 2010
Location: Apple Valley, MN
Posts: 61
Default Re: Soldering iron

Sponsored Links (Register now to hide all advertisements)
I replaced the tip, got the nuts good and tight, was a little more patient and got ‘er done.
Thanks!
Ben38 is offline   Reply With Quote
Old 12-04-2020, 09:50 PM   #7
50fordcoupeman
Senior Member
 
50fordcoupeman's Avatar
 
Join Date: Mar 2016
Location: LaGrande Oregon
Posts: 865
Default Re: Soldering iron

Thats always nice when something works out!!
50fordcoupeman is offline   Reply With Quote
Old 12-04-2020, 10:55 PM   #8
Ray in La Mesa
Senior Member
 
Join Date: May 2010
Location: La Mesa Ca
Posts: 1,157
Default Re: Soldering iron

I have two old Wen 250 watt guns, they work great but you do have to keep the nuts tight. Tips are hard to find so I rebuilt my own using the original stubs that go into the gun and braising on 12 gauge solid house wire for the tip.
Ray in La Mesa is offline   Reply With Quote
Old 12-04-2020, 11:20 PM   #9
J Franklin
Senior Member
 
J Franklin's Avatar
 
Join Date: May 2010
Location: Oregon
Posts: 5,946
Default Re: Soldering iron

Sometimes adding a bit of flux to the joint to unsolder gets it started.
J Franklin is offline   Reply With Quote
Old 12-05-2020, 12:05 AM   #10
cas3
Senior Member
 
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,541
Default Re: Soldering iron

make sure the nuts are tight, and the contact area underneath is clean and your old solder gun will work fine.
cas3 is offline   Reply With Quote
Old 12-05-2020, 06:26 AM   #11
fortyonerag
Senior Member
 
fortyonerag's Avatar
 
Join Date: Sep 2016
Location: Melbourne Australia
Posts: 539
Default Re: Soldering iron

Melt some solder onto the tip of the iron while holding it against the job. The melted solder will act as a heat conductor and help melt the joint.
fortyonerag is offline   Reply With Quote
Old 12-05-2020, 08:27 AM   #12
corvette8n
Senior Member
 
corvette8n's Avatar
 
Join Date: Jul 2010
Location: 36 miles north of Albany NY
Posts: 2,931
Default Re: Soldering iron

Got one of these at HF, you can pull the tip off and use it as a torch.
Attached Images
File Type: jpg E58EB554-6902-4E40-8A63-0F1AE43AE62B.jpg (33.4 KB, 37 views)
corvette8n is offline   Reply With Quote
Old 12-05-2020, 12:55 PM   #13
51woodie
Senior Member
 
51woodie's Avatar
 
Join Date: Apr 2018
Location: Chelmsford, ON Canada
Posts: 524
Default Re: Soldering iron

One thing not mentioned, is that solder alloys have different melting temperatures. Some alloys, i.e. 50/50 and 60/40 are in the 183 to 212C range, while some may need as much as 300C to melt. Silver solder can need 450C or higher to melt. So depending on the original alloy, the melting temp may be lower or higher.

https://www.petervis.com/Education/S...elting%20point.
51woodie is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:19 AM.