Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 10-29-2018, 04:03 PM   #21
WHN
Senior Member
 
Join Date: Mar 2017
Location: Old Lyme Connecticut
Posts: 794
Default Re: Gas tank seeping.

I think if you use a good quality sealer, and follow the directions to the “T”, it will work for you.

Remove tank, coat at least twice, and let tank stand for a couple of days before the second or third coating.

Take your time!!!! Read instructions!!!! Don’t take short cuts!!!!

We have had really good luck doing this. I even think that a good sealer will seal over one that was not done properly. If they seal over rust, why not other potential problems.

What do you have to loose.

Last edited by WHN; 10-29-2018 at 04:14 PM.
WHN is offline   Reply With Quote
Old 10-29-2018, 04:21 PM   #22
37 Coupe
Senior Member
 
37 Coupe's Avatar
 
Join Date: May 2010
Posts: 1,325
Default Re: Gas tank seeping.

Not sure,just I have been following parts like NOS 37-36 Ford parts for years and not Model A,just wondered if ever shown up.I imagine that a NOS would be rust and fatigue free if stored properly. Some NOS parts were manufacture seconds and needed work when it came to a dealership at least sheet metal parts. I bought a NOS 46 Ford fender once that had an issue when stamping out and I was told parts like this were never tossed but depended on the body shop to address.
__________________
"Never complain,never explain"... Henry Ford II
37 Coupe is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 10-29-2018, 09:09 PM   #23
Tinbasher
Senior Member
 
Tinbasher's Avatar
 
Join Date: May 2010
Location: Innisfil, Ontario Canada
Posts: 861
Default Re: Gas tank seeping.

I think as a stop gap repair you should add the later 31 style brace. This will help take the pressure off of the tank. Then you can clean up around the old bracket and seal it with "Seal-all" gas tank sealer or the epoxy gas tank repair kit. This will buy you some time but in the end you'll be removing the tank and doing it properly.

Hope this helps The Old Tinbasher
Tinbasher is offline   Reply With Quote
Old 10-30-2018, 12:14 AM   #24
Tom Wesenberg
Senior Member
 
Tom Wesenberg's Avatar
 
Join Date: May 2010
Location: Mpls, MN
Posts: 27,057
Default Re: Gas tank seeping.

Someone put the dash mount on my 29 Tudor, then soldered the bracket without removing the tank. You can see the thick solder around the bracket, but it's well sealed, and the tank looks like new inside. You can use the large old soldering coppers to safely solder the tank.
Tom Wesenberg is offline   Reply With Quote
Old 10-30-2018, 10:27 AM   #25
29Cabriolet
Senior Member
 
29Cabriolet's Avatar
 
Join Date: Sep 2013
Location: Connecticut
Posts: 262
Default Re: Gas tank seeping.

I too was a victim of this tank damage due to the steering wheel mount. I did not want to remove the tank either. But in response to some advice (even some scoldings to "do it right" from this forum) I did. It was not an easy task but in the long run beneficial. In the process, since the firewall is part of the tank I replaced all the ignition wiring as well. For the tank I removed the riveted mount and TIG welded the the rivet holes. Then had the inside coated by a radiator shop. Repainted the entire tank with a rattle can. Color is one slight shade lighter but un-noticeable. 3 years later, not a drop leaking.
29Cabriolet is offline   Reply With Quote
Old 10-30-2018, 10:47 PM   #26
Lee Mitch
Senior Member
 
Join Date: Feb 2011
Location: Portland, OR.
Posts: 124
Default Re: Gas tank seeping.

My restored car developed this same exact problem. I installed the later style bracket from the dash after the problem developed. My plan was to "seal" around the old bracket where it was weeping, but in 2 years there is no evidence of any gasoline weepage around the old bracket. Go figure!? Maybe that will be your easy way out as, so far, it has been for me.
Lee Mitch is offline   Reply With Quote
Old 11-01-2018, 11:40 AM   #27
DHZIEMAN
Senior Member
 
Join Date: Dec 2016
Location: Sunrise Beach, Mo
Posts: 206
Default Re: Gas tank seeping.

Quote:
Originally Posted by Len Mendonca View Post
My 1931 model A pickup truck gas tank is seeping where the steering wheel shaft attaches to the bottom of the tank. I am looking for an easy way out, like something you put into the tank. I suspect the previous owner used a pour in sealer. I have owned this 1931 Model A pickup truck for 2 years and I saw evidence of a leak but now it is more obvious. I understand ethanol eats away at some of the pour in sealers.

Is there an easy way out for this?
Gas seepage or leaks of any kind are bothersome from a safety standpoint. And doing a repair with sealer does not solve the original leak problem, it just band-aides it! And once the sealer starts breaking down, ya got bigger problems. The easy safe way to fix this is really not easy but is the right way. Take out the tank, and do it right! Everything else in my estimation, just prolongs the agony.
DHZIEMAN is offline   Reply With Quote
Old 11-01-2018, 03:52 PM   #28
Synchro909
Senior Member
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 3,527
Default Re: Gas tank seeping.

Quote:
Originally Posted by DHZIEMAN View Post
Gas seepage or leaks of any kind are bothersome from a safety standpoint. And doing a repair with sealer does not solve the original leak problem, it just band-aides it! And once the sealer starts breaking down, ya got bigger problems. The easy safe way to fix this is really not easy but is the right way. Take out the tank, and do it right! Everything else in my estimation, just prolongs the agony.
Like many who have posted on this thread, you seem to assume the sealer will break down. Why? I used sealer for the first time over 20 years ago and that tank still doesn't leak a drop. It is one where I used one of my 1931 style column support brackets and then sealed the tank. I expect better sealers are available now than when I did that, too.
A good quality sealer properly applied will outlast us and most likely, the car.
I've also had good success when treating a rusty tank by using phosphoric acid (which leaves a white powdery residue) to clean out the rust, then using the best sealer I can find. In my most recent job, I solved both problems (rust and a leak) at the same time.
__________________
My Model A is not slow - it's buffering.
Synchro909 is offline   Reply With Quote
Old 11-09-2018, 11:33 AM   #29
dmaxweb
Senior Member
 
dmaxweb's Avatar
 
Join Date: May 2010
Location: Williamsburg, VA
Posts: 277
Default Re: Gas tank seeping.

I used 31 bracket and sealed around tank bracket with Marine-Tex Gray epoxy. 8+ years and not a drop leaking.
dmaxweb is offline   Reply With Quote
Old 11-09-2018, 12:02 PM   #30
Paul Bjarnason
Junior Member
 
Join Date: Jul 2018
Posts: 21
Default Re: Gas tank seeping.

I just bought an NOS Model A tank at the latest Hershey. Until I stumbled upon it, I didn't think they existed.
Paul Bjarnason is offline   Reply With Quote
Old 11-09-2018, 12:37 PM   #31
37 Coupe
Senior Member
 
37 Coupe's Avatar
 
Join Date: May 2010
Posts: 1,325
Default Re: Gas tank seeping.

Quote:
Originally Posted by paulbearson View Post
I just bought an NOS Model A tank at the latest Hershey. Until I stumbled upon it, I didn't think they existed.
Was it a '31? or an earlier one?
__________________
"Never complain,never explain"... Henry Ford II
37 Coupe is offline   Reply With Quote
Old 11-09-2018, 12:55 PM   #32
HoarseWhisperer
Senior Member
 
HoarseWhisperer's Avatar
 
Join Date: May 2010
Location: Ontario, Canada
Posts: 1,465
Default Re: Gas tank seeping.

After the "stop gap" methods; the permanent method. Right TinBasher?



__________________
I know a lot of things; I just can't remember them all.

1928 CCPU 82-A
1931 Roadster 40-B Dlx (Canadian)
HoarseWhisperer is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:33 PM.