11-20-2017, 09:15 AM | #21 |
Senior Member
Join Date: Oct 2017
Posts: 563
|
Re: torque wrench
Torque wrenches are most accurate or calibrated about mid scale, a 0-150 foot lb wrench is not going to be suitable at 1 pound torque range. Something like a 0-15 with analog dial would be what you want.
|
11-20-2017, 11:55 AM | #22 |
Senior Member
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,088
|
Re: torque wrench
Set the carrier (side) bearing pre-load first, while the pinion is not affecting the feel. Do as Tom says. New bearings should be set tighter than used bearings. I set carrier bearings with the axles in the vertical position, and use feeler gauges in place of gaskets to adjust things. Use feelers under the housings to adjust back-lash too, then on final assembly replace the gauges with appropriate thickness of gaskets. Do not tighten side-housing bolts without feelers or gaskets in place or the housings will bend and you'll have leaks. Use care, go slow, and have fun!
|
Sponsored Links (Register now to hide all advertisements) |
|
12-29-2018, 01:52 AM | #23 |
Senior Member
Join Date: Aug 2010
Location: Geelong Australia
Posts: 119
|
Re: torque wrench
I realise the end of this thread is a year gone by ,,but can I ask when setting the pinion and side bearings preload do we do them dry and clean of any lube ,,,as when dry and clean there appears to be less drag ,,,thanks ,,
|
12-29-2018, 06:41 PM | #24 |
Senior Member
Join Date: May 2010
Location: now Kuna, Idaho
Posts: 3,779
|
Re: torque wrench
Just be sure that you do NOT try to use the "click" type to measure preload! Preload is measured while the shaft is rotating, thus the need for a beam or dial type wrench.
|
12-29-2018, 08:06 PM | #25 |
Senior Member
Join Date: May 2010
Location: Portland OR
Posts: 6,340
|
Re: torque wrench
"I would never go back to a beam style, yuck."
You you can't set preload with a click type. Someone back in the string made it sound like you could give a good pull on the gear and it would spin one or more full revolution by it self! That would be way too loose. That would be like -20 inch pounds. (Yes I see this is an old one brought back up)
__________________
I know the voices aren't real but damn they have some good ideas! |
12-30-2018, 03:58 PM | #26 |
Senior Member
Join Date: Dec 2011
Location: SW Idaho
Posts: 970
|
Re: torque wrench
Sponsored Links (Register now to hide all advertisements)
|
12-31-2018, 08:43 AM | #27 |
Senior Member
Join Date: Jan 2016
Posts: 2,098
|
Re: torque wrench
New Link for the inch drive, I could not edit my old post.
https://www.harborfreight.com/14-in-...nch-61277.html When I set my pre load I did it as Tom mentioned and 4,000 miles later it is still good. Originally I set it with a inch torque wrench but felt that it was too tight. |
12-31-2018, 11:03 AM | #28 | |
Senior Member
Join Date: May 2010
Location: now Kuna, Idaho
Posts: 3,779
|
Re: torque wrench
Quote:
|
|
12-31-2018, 11:27 AM | #29 |
Senior Member
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,044
|
Re: torque wrench
__________________
If you don't hear a rumor by 10 AM, start one!. Got my education out behind the barn! |
12-31-2018, 01:47 PM | #30 | |
Senior Member
Join Date: May 2010
Location: Illinois
Posts: 2,184
|
Re: torque wrench
Quote:
I use this kind of torque wrench for rear ends and stromberg carbs. When I was in aviation mechanics school my instructor pointed out that beam wrenches never go out of calibration. If it points to zero at rest it is calibrated John |
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|