Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 09-20-2019, 07:09 PM   #1
walkerlakeprinter
Senior Member
 
walkerlakeprinter's Avatar
 
Join Date: May 2010
Location: Walker Lake, Nevada
Posts: 304
Question How to measure front wheels to straight ahead

I want to mount my steering wheel in the X position with my "suicide knob" at 2 o'clock. What is a good way to determine when the front wheels are in the straight ahead position? I have a 1929 Coupe with the splined shaft.
walkerlakeprinter is offline   Reply With Quote
Old 09-20-2019, 07:14 PM   #2
Kurt in NJ
Senior Member
 
Kurt in NJ's Avatar
 
Join Date: May 2010
Location: on the Littlefield
Posts: 6,140
Default Re: How to measure front wheels to straight ahead

When you go for a drive make note of the steering wheel position

If you can't drive it take someone long and straight and lay it against the side of the tires, get so both fronts are equal

Stand back and take a sight look down across the tires, make equal

The front wheels should be a little closer at the front ( toe in )
Kurt in NJ is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 09-20-2019, 07:28 PM   #3
walkerlakeprinter
Senior Member
 
walkerlakeprinter's Avatar
 
Join Date: May 2010
Location: Walker Lake, Nevada
Posts: 304
Default Re: How to measure front wheels to straight ahead

Thanks! I can't drive the car yet, so I will find something long and straigt and go from there.
walkerlakeprinter is offline   Reply With Quote
Old 09-20-2019, 11:35 PM   #4
Russ/40
Senior Member
 
Russ/40's Avatar
 
Join Date: May 2010
Location: Santee, California
Posts: 3,505
Default Re: How to measure front wheels to straight ahead

Basically, you cant. The toe in spec is too tight for any crude method. Get it to an alignment shop.
Russ/40 is offline   Reply With Quote
Old 09-21-2019, 09:15 AM   #5
walkerlakeprinter
Senior Member
 
walkerlakeprinter's Avatar
 
Join Date: May 2010
Location: Walker Lake, Nevada
Posts: 304
Default Re: How to measure front wheels to straight ahead

The nearest alignment shop is more than 70 miles away. I will have to use a crude method until the car is safe to drive. The longest trip my car had was 13 miles to town and back, ten years ago. One step at a time. Always something to fix or adjust. At 71 I am learning more each day, and I love it.
walkerlakeprinter is offline   Reply With Quote
Old 09-21-2019, 04:50 PM   #6
duke36
Senior Member
 
Join Date: Jun 2015
Posts: 1,414
Default Re: How to measure front wheels to straight ahead

Sponsored Links (Register now to hide all advertisements)
One method is to take a straight 2 x4 or metal tube, etc. and place next to tires front to back. Visually check both sides similar to the assembly line conveyor tracks.. Then place the wheel temporarily on the spline end, and rotate lock to lock, count the turns of the wheel with tape on it, then turn back the opposite direction approx. 1/2 the turns. That should closely center the steering shaft ( and wheel) with minimal freeplay and equal lash at the extremes of the steering gear. Also, do you have a woodruff key on the threaded ends? The center position should be close to the tires aligned. This is with a stock pitman arm.
duke36 is offline   Reply With Quote
Old 09-21-2019, 05:15 PM   #7
Purdy Swoft
Senior Member
 
Purdy Swoft's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 8,099
Default Re: How to measure front wheels to straight ahead

The front of the wheels must towed in 1/16 closer than the back of the front wheels . With the wheels adjusted closer at the front keeps the wheels going in a straight line . If the front end isn't towed in correctly it will wander and if towed out the least fraction it can cause shimmy or death wobble . Setting the toe in can be a pain . I prefer having the toe in set at a front end alignment shop .
Purdy Swoft is offline   Reply With Quote
Old 09-22-2019, 03:17 AM   #8
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: How to measure front wheels to straight ahead

Which is your concern, the wheels/tires pointing in the straight ahead position for steering wheel alignment, or, toe-in setting ?

It sounds to me like you just want the steering wheel straight ahead for now.
Patrick L. is offline   Reply With Quote
Old 09-22-2019, 07:54 PM   #9
Tinbasher
Senior Member
 
Tinbasher's Avatar
 
Join Date: May 2010
Location: Innisfil, Ontario Canada
Posts: 1,173
Default Re: How to measure front wheels to straight ahead

Here's a trick to check the placement of the front and rear wheels to each other in a straight line. Get about 12' of elastic thread and attach a fish hook or safety pin opened up on each end. Then at centre wheel height hook the thread to the inside or the tire and bring it around to the outside, then down the side of the car to the rear tire at the centre and hook the elastic on the inside of the tire. If the front and rear wheels are in alignment the thread will touch the front and rear of each tire. With no gaps. This will also tell you that there's "Zero" toe. Hope this is clear enough. JP
Tinbasher is offline   Reply With Quote
Old 09-23-2019, 04:14 AM   #10
Wick
Senior Member
 
Wick's Avatar
 
Join Date: May 2010
Location: Gwynn's Island Va
Posts: 1,380
Default Re: How to measure front wheels to straight ahead

Unhook the steering arm from the box. Rotate steering wheel right and left (lock to lock) count the turns
Of the wheel. If the # is 4 total then 2 turns from lock is the center. This is called clocking the wheel.
Install wheel where you want it. Now line up/adjust front wheels to the steering arm.
Wick
Wick is offline   Reply With Quote
Old 09-23-2019, 07:52 PM   #11
supergnat
Senior Member
 
supergnat's Avatar
 
Join Date: Jan 2011
Location: Palmyra, NJ
Posts: 475
Default Re: How to measure front wheels to straight ahead

I was given this tool suggestion and it seems to work pretty well at least to get you in the ball park so you could go to an alignment shop. I use two Harbor Freight tape measures as part of the tool kit. This was in one of the national club magazines but I don't know which one.
Good luck,
Supergnat
Attached Files
File Type: pdf Front end alignment tool.pdf (619.7 KB, 36 views)
supergnat is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:14 PM.