Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 09-26-2019, 05:51 AM   #1
Juggler
Senior Member
 
Juggler's Avatar
 
Join Date: Aug 2010
Location: Phoenix AZ/Bath UK
Posts: 481
Default Holes drilled in dipper tray

I took the motor out of my Coupe (nothing wrong with it - swapped for rebuilt full pressure ohv) and Dear Old Dad decided to drop the pan and check the bottom end with a view to putting it in the '30 Roadster he's building from the ground up.

Found to be all good, clean bores and shims all still present, but somebody in before us has drilled/punched 4 holes in the dipper tray.





We can't figure what the benefit of that might be and will probably just weld them back up. Was this a thing back in the day? Car originally came down from Nebraska if that makes any difference.

Many thanks
Juggler is offline   Reply With Quote
Old 09-26-2019, 06:41 AM   #2
WHN
Senior Member
 
Join Date: Mar 2017
Location: Connecticut Shoreline
Posts: 1,815
Default Re: Holes drilled in dipper tray

Weld them shut!
WHN is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 09-26-2019, 06:48 AM   #3
BRENT in 10-uh-C
Senior Member
 
BRENT in 10-uh-C's Avatar
 
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,466
Default Re: Holes drilled in dipper tray

I would leave them as-is. Won't hurt a thing. The dipper wells are the only area where the rod dipper needs to initially contact (scoop) oil during start-up. From there the oil pump will replenish faster than the holes will drain.
__________________
.

BRENT in 10-uh-C
.
www.model-a-ford.com
...(...Finally Updated!! )

.
BRENT in 10-uh-C is offline   Reply With Quote
Old 09-26-2019, 07:22 AM   #4
Juggler
Senior Member
 
Juggler's Avatar
 
Join Date: Aug 2010
Location: Phoenix AZ/Bath UK
Posts: 481
Default Re: Holes drilled in dipper tray

I understand that they won't hurt - just wondered why anybody would do it in the first place?
Juggler is offline   Reply With Quote
Old 09-26-2019, 07:44 AM   #5
Railcarmover
BANNED
 
Join Date: Apr 2017
Location: Sacramento
Posts: 1,262
Default Re: Holes drilled in dipper tray

its splitting hairs,but those holes lower the level of oil the rod splashes through..splash oil is a big part of engine lubrication design.
Railcarmover is offline   Reply With Quote
Old 09-26-2019, 08:28 AM   #6
Joe K
Senior Member
 
Joe K's Avatar
 
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,160
Default Re: Holes drilled in dipper tray

Sponsored Links (Register now to hide all advertisements)
IIRC, they may be OEM. Certainly about lowering the level to reduce splash and windage.

Page 576 of the Service Bulletins talks about "lowering" the dipper tray. "And other modifications." (including the oil pump shaft shield.)

I would leave. You might put off having to go with one of those "oil breather" type oil fill tube tops for a bit longer.

Joe K
__________________
Shudda kept the horse.
Joe K is offline   Reply With Quote
Old 09-26-2019, 08:31 AM   #7
Kurt in NJ
Senior Member
 
Kurt in NJ's Avatar
 
Join Date: May 2010
Location: on the Littlefield
Posts: 6,132
Default Re: Holes drilled in dipper tray

in looking at the evolution of the dipper tray, and mentions of changes to help oil consumption my thoughts are the oil pump shield was also used in the time frame of holes in dipper tray---being that the center cam bearing is pressure oiled it can also "leak", and if the clearance gets about .005 the bearing clearance area is about the same as the oil discharge pipe in the valve chamber ----so the shield insures that all the oil hits the tray ----this keeps the dipper troughs filled, to limit the tray from being overfilled at multiple angles holes were added,
Kurt in NJ is offline   Reply With Quote
Old 09-26-2019, 10:55 AM   #8
Bob C
Senior Member
 
Join Date: May 2010
Location: So Cal
Posts: 8,697
Default Re: Holes drilled in dipper tray

Here are some more dipper trays.


Bob
Attached Images
File Type: jpg UNADJUSTEDNONRAW_thumb_75f.jpg (95.0 KB, 522 views)
Bob C is offline   Reply With Quote
Old 09-26-2019, 11:36 AM   #9
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Holes drilled in dipper tray

I'm not a big fan of the holes in the low point of the dipper troughs,[ bottom pic ] When sitting the oil will drain leaving the rod bearings to run dry for the time it takes for the oil pump to fill them. Its the dry running of bearings I'm not a fan of. Those 4 holes I'd braze.
Patrick L. is offline   Reply With Quote
Old 09-26-2019, 01:20 PM   #10
BRENT in 10-uh-C
Senior Member
 
BRENT in 10-uh-C's Avatar
 
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,466
Default Re: Holes drilled in dipper tray

Quote:
Originally Posted by Patrick L. View Post
I'm not a big fan of the holes in the low point of the dipper troughs,[ bottom pic ] When sitting the oil will drain leaving the rod bearings to run dry for the time it takes for the oil pump to fill them. Its the dry running of bearings I'm not a fan of. Those 4 holes I'd braze.


I guess I am missing it. Which one has holes at the bottom of the well that would cause the oil to leak out?





.
.
__________________
.

BRENT in 10-uh-C
.
www.model-a-ford.com
...(...Finally Updated!! )

.
BRENT in 10-uh-C is offline   Reply With Quote
Old 09-26-2019, 01:39 PM   #11
Gold Digger
Senior Member
 
Join Date: Nov 2011
Location: Arkansas & Alaska
Posts: 642
Default Re: Holes drilled in dipper tray

I remember a friend that has been long pasted on told me he raced model A's down in Texas in the days of model A's. He told me the secret of running them was to drill more and bigger holes in the splash tray so the oil ran back down in the bottom of the pan quicker. I have never came across one that has been drilled yet. I wonder if oil built up in this area and caused oil flooding. May have just been someone's big idea.
Gold Digger is offline   Reply With Quote
Old 09-26-2019, 02:13 PM   #12
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Holes drilled in dipper tray

Quote:
Originally Posted by Juggler View Post
I took the motor out of my Coupe (nothing wrong with it - swapped for rebuilt full pressure ohv) and Dear Old Dad decided to drop the pan and check the bottom end with a view to putting it in the '30 Roadster he's building from the ground up.

Found to be all good, clean bores and shims all still present, but somebody in before us has drilled/punched 4 holes in the dipper tray.





We can't figure what the benefit of that might be and will probably just weld them back up. Was this a thing back in the day? Car originally came down from Nebraska if that makes any difference.

Many thanks



Lower picture.
Patrick L. is offline   Reply With Quote
Old 09-26-2019, 02:30 PM   #13
Kohnke Rebabbitting
Senior Member
 
Join Date: May 2010
Location: 60615,330th Ave.,Clare, Iowa, 50524
Posts: 1,457
Default Re: Holes drilled in dipper tray

They serve no valid purpose.

The holes in the dipper tray, cuts back considerably, the oil available to continually feed the dipper tray. Bad idea.

I think that it was one time, a write-in mechanics tip in some Tips, and Tricks Magazine.

If when building a Model T Speedster, it was recommended you put a 1/2 inch high dam in the back of the pan to raise the oil level to feed the rods more oil at high speeds, that does work very well.

My guess, it was done to cut back the oil splash under the pistons, there for cutting oil burning on wore out pistons, and rings.

But these holes, are going the wrong way, by dropping the oil level. Not Good, No warranty !

Herm.
Kohnke Rebabbitting is offline   Reply With Quote
Old 09-26-2019, 04:45 PM   #14
Juggler
Senior Member
 
Juggler's Avatar
 
Join Date: Aug 2010
Location: Phoenix AZ/Bath UK
Posts: 481
Default Re: Holes drilled in dipper tray

Thanks Herm, and everybody else

In reality we'll just put another tray in from the pile, sans perforations

Brett and Patrick - there's no hole in the bottom of the well although it does look like it in the pic. It's a spot of oil that Dad missed, and a trick of the light

Cheers

A
Juggler is offline   Reply With Quote
Old 09-26-2019, 04:56 PM   #15
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Holes drilled in dipper tray

Quote:
Originally Posted by Juggler View Post
Thanks Herm, and everybody else

In reality we'll just put another tray in from the pile, sans perforations

Brett and Patrick - there's no hole in the bottom of the well although it does look like it in the pic. It's a spot of oil that Dad missed, and a trick of the light

Cheers

A


AH, OK. That makes sense as there isn't a 'hole' in the adjacent dipper tray.
Sure looks like its a drilled hole though doesn't it.
So, then, I agree that the holes on the top of the tray won't hurt.
Patrick L. is offline   Reply With Quote
Old 09-26-2019, 06:05 PM   #16
ursus
Senior Member
 
Join Date: May 2010
Location: Oregon
Posts: 1,366
Default Re: Holes drilled in dipper tray

Ford punched drain holes in upper part of the Model-B dipper tray for a reason. Drain holes were also built into the bottom of the valve chamber to permit more oil to pass into the dipper tray from above. The Model-B engine was introduced as "the improved 4-cylinder engine".
ursus is offline   Reply With Quote
Old 09-26-2019, 06:26 PM   #17
Jim Brierley
Senior Member
 
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,064
Default Re: Holes drilled in dipper tray

Most Model B engines came from the factory with (I think 4) 4 holes about 1" in diameter, purpose, I'm not sure but no need to weld the ones you have shut.
Jim Brierley is offline   Reply With Quote
Old 09-26-2019, 07:41 PM   #18
Bob C
Senior Member
 
Join Date: May 2010
Location: So Cal
Posts: 8,697
Default Re: Holes drilled in dipper tray

Vince has some information on his site about the holes. http://www.fordgarage.com/pages/boilpans.htm


Bob
Bob C is offline   Reply With Quote
Old 09-27-2019, 10:02 AM   #19
DanK
Member
 
Join Date: Aug 2010
Location: San Diego
Posts: 31
Default Re: Holes drilled in dipper tray

Quote:
Originally Posted by Kohnke Rebabbitting View Post

My guess, it was done to cut back the oil splash under the pistons, there for cutting oil burning on wore out pistons, and rings.

But these holes, are going the wrong way, by dropping the oil level. Not Good, No warranty !

Herm.
My Grandfather was a mechanic at a Ford dealership when Model A's were new. My Dad started working with him as a teenager. My Dad told me the above was the reason for the holes in the tray.
DanK is offline   Reply With Quote
Old 09-27-2019, 11:48 AM   #20
Jeff/Illinois
Senior Member
 
Jeff/Illinois's Avatar
 
Join Date: May 2010
Posts: 2,787
Default Re: Holes drilled in dipper tray

The weird 'thing' about dipper trays, at least to me (and I understand their function I get it) is that when the Boss 302 motors hit the street they had a WINDAGE tray to keep the oil in place. sort of, when hard cornering and acceleration was put to the motor. When I was a Parts Mgr. at the local Ford dealer back then I was ordering windage tray hardware, regularly, for the guys who were drag racing. They didn't like re-using the hardware.

Do you suppose Mr. Ford foresaw THAT type of racing application in the Model A
Jeff/Illinois is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:25 AM.