Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 01-23-2014, 12:49 PM   #1
34hardhead
Junior Member
 
34hardhead's Avatar
 
Join Date: Aug 2010
Location: Richmond Va.
Posts: 27
Default 1934 Ford Radio bracket id

I have several of these brackets, and cannot figure out how they fit the
Radio, I think they go behind the radio to the firewall, but do not know for sure, also are they for an ash tray radio or glove box radio,
Attachment 162701

Attachment 162702

Attachment 162703
34hardhead is offline   Reply With Quote
Old 01-23-2014, 12:56 PM   #2
deuce lover
Senior Member
 
deuce lover's Avatar
 
Join Date: May 2010
Location: Southern France
Posts: 3,605
Default Re: 1934 Ford Radio bracket id

Your attachments did not come thru for me
deuce lover is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 01-23-2014, 12:57 PM   #3
Lawson Cox
Senior Member
 
Lawson Cox's Avatar
 
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 5,397
Default Re: 1934 Ford Radio bracket id

Nor me.
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes.

It is better to be seen, than viewed.


"We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm".
Lawson Cox is offline   Reply With Quote
Old 01-23-2014, 01:01 PM   #4
34hardhead
Junior Member
 
34hardhead's Avatar
 
Join Date: Aug 2010
Location: Richmond Va.
Posts: 27
Default Re: 1934 Ford Radio bracket id

Can you see these
Attached Images
File Type: jpg radio bracket 001.JPG (209.1 KB, 20 views)
File Type: jpg radio bracket 002.JPG (206.2 KB, 14 views)
File Type: jpg radio bracket 003.JPG (164.5 KB, 16 views)
34hardhead is offline   Reply With Quote
Old 01-23-2014, 01:53 PM   #5
34ford
Senior Member
 
34ford's Avatar
 
Join Date: May 2010
Location: franklin park ill.
Posts: 174
Default Re: 1934 Ford Radio bracket id

that is the rear bracket for the glove box radio
34ford is offline   Reply With Quote
Old 01-26-2014, 10:26 AM   #6
fordbug79
Junior Member
 
Join Date: May 2010
Location: SE Texas
Posts: 12
Default Re: 1934 Ford Radio bracket id

Sponsored Links (Register now to hide all advertisements)
Would you be willing to sell one of the brackets as I am in need of one.

Thanks
fordbug79 is offline   Reply With Quote
Old 01-26-2014, 11:03 AM   #7
Randy
Senior Member
 
Randy's Avatar
 
Join Date: May 2010
Location: Austin
Posts: 684
Default Re: 1934 Ford Radio bracket id

Since no one has mentioned how it fits and that seemed to be part of the original question, here goes: the shouldered stud and the pointed end go to the firewall with the pointed end up, the shouldered stud going through the hole in the firewall (which has to be punched out if the car never had a glove box radio before) with a nut on the outside and the point digging into the firewall insulator (possibly designed to pierce the paint to create a ground, not sure?). The shoulder is there to allow tightening of the bolt without crushing the firewall insulator. The other stud goes through the hole in the bracket on the back of the radio with a nut to support the back of the radio.

Last edited by Randy; 01-26-2014 at 03:11 PM.
Randy is offline   Reply With Quote
Old 01-26-2014, 11:56 AM   #8
Pete/Ct.
Senior Member
 
Join Date: May 2010
Location: Kensington,CT
Posts: 308
Default Re: 1934 Ford Radio bracket id

If you are selling them I could use one also, thanks. Pete/Ct.
Pete/Ct. is offline   Reply With Quote
Old 01-26-2014, 01:13 PM   #9
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Posts: 7,441
Default Re: 1934 Ford Radio bracket id

I believe you meant to write that the pointed end faces up.
DavidG is offline   Reply With Quote
Old 01-26-2014, 03:10 PM   #10
Randy
Senior Member
 
Randy's Avatar
 
Join Date: May 2010
Location: Austin
Posts: 684
Default Re: 1934 Ford Radio bracket id

Quote:
Originally Posted by DavidG View Post
I believe you meant to write that the pointed end faces up.
Yes, that's correct, sorry. I corrected it above. Thanks!
Randy is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:57 AM.