Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 08-04-2020, 02:38 PM   #1
FlatheadEric
Member
 
FlatheadEric's Avatar
 
Join Date: Oct 2017
Location: Raglan, New Zealand
Posts: 97
Default NOS 1938-48 24 Stud Head Gaskets

I will soon be putting my '39 24 stud engine back together with new mains, big ends, rings, cam followers, valves etc.

I have got two pairs of NOS 1938-48 24 stud head gaskets, all still with some of the preserving wax on the metal fire rings. This scrapes off easily with a fingernail.

They have the following stamped on them:
Ford USA
Detroit Gasket Mfg Co
Steelbestos
41A-6051

My questions are:
Are these a good type of gasket to use?
If so, what is the best sealer to use on these asbestos gaskets?

20200726_104918.jpg

20200726_104533.jpg

20200726_104600.jpg

20200726_104546.jpg
FlatheadEric is offline   Reply With Quote
Old 08-04-2020, 02:48 PM   #2
rockfla
Senior Member
 
rockfla's Avatar
 
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,926
Default Re: NOS 1938-48 24 Stud Head Gaskets

The gasket you have "would" probably be good....Were it me, a "new" gasket has more "modern" technology built into it SO the ability to perform (in my mind) would also be better IMO the cost is "cheap" insurance. I used a copper coat spray on mine before I put it back together!!! I also anti seized the studs and the tops of the head stud holes to help the next shlepp like me who work on it to hopefully make pulling the heads easier than what I had!!!
Attached Images
File Type: jpg 39merceng7.jpg (85.4 KB, 36 views)
File Type: jpg 39merceng2.jpg (52.9 KB, 30 views)
rockfla is online now   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 08-04-2020, 03:54 PM   #3
jimTN
Senior Member
 
Join Date: May 2010
Location: Powell, TN
Posts: 2,503
Default Re: NOS 1938-48 24 Stud Head Gaskets

I prefer all metal faced gaskets and copper coat on them. You can take the engine apart then. The type of gaskets you have make it difficult to get a head off if it has studs and requires a lot of clean up.
jimTN is offline   Reply With Quote
Old 08-04-2020, 04:22 PM   #4
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: NOS 1938-48 24 Stud Head Gaskets

Quote:
Originally Posted by FlatheadEric View Post
I will soon be putting my '39 24 stud engine back together with new mains, big ends, rings, cam followers, valves etc.

I have got two pairs of NOS 1938-48 24 stud head gaskets, all still with some of the preserving wax on the metal fire rings. This scrapes off easily with a fingernail.

They have the following stamped on them:
Ford USA
Detroit Gasket Mfg Co
Steelbestos
41A-6051

My questions are:
Are these a good type of gasket to use?
If so, what is the best sealer to use on these asbestos gaskets?

Attachment 438008

Attachment 438009

Attachment 438010

Attachment 438011
I use these religiously and have never had an issue. I do spray them with coppercoat. In my humble opinion, newer is not necessarily better.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 08-04-2020, 04:41 PM   #5
FlatheadEric
Member
 
FlatheadEric's Avatar
 
Join Date: Oct 2017
Location: Raglan, New Zealand
Posts: 97
Default Re: NOS 1938-48 24 Stud Head Gaskets

Thanks all for your comments.
I suppose there must have been many thousands of these in service over the years.
FlatheadEric is offline   Reply With Quote
Old 08-04-2020, 04:51 PM   #6
cadillac512
Senior Member
 
cadillac512's Avatar
 
Join Date: Apr 2019
Location: Kansas
Posts: 897
Default Re: NOS 1938-48 24 Stud Head Gaskets

Sponsored Links (Register now to hide all advertisements)
As good or better (due to the asbestos content) as any available head gasket in my opinion. Modern is quite often not better as far as head gasket materials go.



Terry
__________________
"It don't take but country smarts to solve the problem" (Smokey Yunick)


'41 Merc Town Sedan / 260" 8CM engine
'66 Fairlane four door / "warmed up" 302
cadillac512 is offline   Reply With Quote
Old 08-04-2020, 06:06 PM   #7
Terry,OH
Senior Member
 
Terry,OH's Avatar
 
Join Date: May 2010
Posts: 4,725
Default Re: NOS 1938-48 24 Stud Head Gaskets

The 41A gasket is the correct gasket for the 81A engine. You will note the small coolant holes are at the front and the rear coolant holes are larger.
Terry,OH is offline   Reply With Quote
Old 08-05-2020, 01:31 AM   #8
FlatheadEric
Member
 
FlatheadEric's Avatar
 
Join Date: Oct 2017
Location: Raglan, New Zealand
Posts: 97
Default Re: NOS 1938-48 24 Stud Head Gaskets

Thanks guys. Majority opinion is that they are fit for purpose so I will get coppercoat as suggested by Kube and rockfla and put them into service.
The engine will be loaded up with new parts and I don't plan on taking the heads off again any time soon.
FlatheadEric is offline   Reply With Quote
Old 08-05-2020, 07:34 AM   #9
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: NOS 1938-48 24 Stud Head Gaskets

Quote:
Originally Posted by FlatheadEric View Post
Thanks guys. Majority opinion is that they are fit for purpose so I will get coppercoat as suggested by Kube and rockfla and put them into service.
The engine will be loaded up with new parts and I don't plan on taking the heads off again any time soon.
Later this week, I'll be installing a pair of these on a '40 engine.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 08-05-2020, 07:12 PM   #10
Bored&Stroked
Senior Member
 
Bored&Stroked's Avatar
 
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,009
Default Re: NOS 1938-48 24 Stud Head Gaskets

Quote:
Originally Posted by FlatheadEric View Post
The engine will be loaded up with new parts and I don't plan on taking the heads off again any time soon.
I think I've said the same thing to myself . . . many times in my life. LOL
Bored&Stroked is offline   Reply With Quote
Old 08-05-2020, 08:11 PM   #11
Jack E/NJ
Senior Member
 
Jack E/NJ's Avatar
 
Join Date: May 2010
Posts: 2,171
Default Re: NOS 1938-48 24 Stud Head Gaskets

Grease 'em. 8^) Jack E/NJ
Jack E/NJ is online now   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:15 AM.