|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
03-27-2021, 10:21 AM | #1 |
Junior Member
Join Date: Jan 2019
Posts: 3
|
53 cam for auto
I just started working on a 53 Sunliner (heavy) with a Fordomatic. I'm going for a .020 overbore on original flathead. I'm rebuilding the motor to appear all stock, but would like to bump HP with a better cam if possible. My stock cam is bad. The fella helping me with the motor says if I go with a performance cam, my automatic won't shift right. Anybody have any thoughts or experience with this. Any suggestions for cam, or someone to regrind mine? Thanks.
|
03-27-2021, 10:26 AM | #2 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: 53 cam for auto
Unless you make a lot of other modifications to the engine, just about any aftermarket cam will reduce performance. The later stock cams are about as good as they come for this application IMO. One thing that will really help is uping the compression ratio by reducing the clearance between the piston and the head to around .050. If you can not locate a good original cam, there are several cam grinders here on the Barn that should be able to grind you one.
And welcome to the Barn! |
Sponsored Links (Register now to hide all advertisements) |
|
03-27-2021, 11:25 AM | #3 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,316
|
Re: 53 cam for auto
I was considering putting an Isky Max-1 cam in the '51 Merc that went into my '51 coupe (also a relatively heavy car), and after much research and discussion, stayed with the stock Merc cam. Also, I am a real fan of an 1/8" overbore on these engines. This will yield 258 ci, 3 more than the vaunted 4" Mercury crankshaft. I figure that if the Ford engineers considered the expensive option of an entirely new crankshaft and pistons was justified because of the increased weight of the Mercury's, why not take the much cheaper (if not free) option of a safe overbore? Just about all of these engines will go out to 3 3/8" with no problem, so 1/8" leaves room for further corrections. If you need new pistons anyway, why not go the extra for about the same piston cost?
|
03-27-2021, 12:35 PM | #4 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,316
|
Re: 53 cam for auto
I also agree with "JSeery" about optimizing the "squish" between the piston crown and head. On the first couple of engines I built (pre "Ford barn"), I just threw on a set of "Hi-Compression" heads without checking and was always slightly disappointed with their performance. (I have less confidence about the manufacturers holding tolerances than I was then.) On the last two, I have spent quite a bit of time optimizing the piston/head clearance and have been much more satisfied with the results.
A small base Rochester carburetor on a bored out Mercury manifold results in a nice street engine with a notable increase in power without busting your budget. |
03-27-2021, 12:47 PM | #5 |
Senior Member
Join Date: Oct 2019
Location: Carthage , Tennessee
Posts: 199
|
Re: 53 cam for auto
Hi Denny ,
I am planning on taking your advice on the carb and manifold combo . I was just going to ask you what carb you used,,,,and exactly what size you bored the intake to . I’m leaning towards keeping my stock Mercury intake after all . Tommy |
03-27-2021, 01:08 PM | #6 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,316
|
Re: 53 cam for auto
Sponsored Links (Register now to hide all advertisements)
Rather than cluttering up this guy's thread, I'll send you a PM. Denny |
03-27-2021, 01:24 PM | #7 | |
Senior Member
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
|
Re: 53 cam for auto
Quote:
The FordOmatic is generally set to 500 RPM or less. Get a good stock Ford or Mercury cam.
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES |
|
03-27-2021, 04:43 PM | #8 |
Senior Member
Join Date: Aug 2017
Location: ohio
Posts: 986
|
Re: 53 cam for auto
8CM Merc cam is ideal imo.
|
03-27-2021, 06:21 PM | #9 |
Junior Member
Join Date: Oct 2020
Posts: 14
|
Re: 53 cam for auto
I’m still gathering parts but I got a Canadian aluminum four bolt intake and a 1956? Rochester 2gc carb.
Sent from my iPhone using Tapatalk |
03-27-2021, 08:05 PM | #10 |
Junior Member
Join Date: Jan 2019
Posts: 3
|
Re: 53 cam for auto
Thanks for the info. Is the Merc cam more lift or duration or both? How can I find the guys on the barn to get cams from? I see a swap area, is that where I should be looking? I've been doing a lot of reading and I was planning on going with .050 clearance on heads. I would like to build a hotter motor but I think this car needs to stay close to stock. Thanks Guys I appreciate the information.
|
03-27-2021, 08:14 PM | #11 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: 53 cam for auto
A lot of the posters on the Barn are also parts vendors, rebuilders, shop owners, etc. One that grinds cams is Pete.
https://www.fordbarn.com/forum/member.php?u=2 You may have to increase your number of post before you can contact Barn members. I think you have to have at least 10 post, it may be 20. |
03-27-2021, 08:27 PM | #12 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: 53 cam for auto
Both. Here are some of the early Ford cam specs.
|
03-27-2021, 08:40 PM | #13 | |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,316
|
Re: 53 cam for auto
Quote:
If you would like to see it, I could send you a copy of the PM I am sending to Tommy. |
|
03-27-2021, 09:46 PM | #14 |
Senior Member
Join Date: Jan 2011
Posts: 342
|
Re: 53 cam for auto
I have a cam that has cast "1cm" on it--is it the same as an 8cm? Was in a block with 8cm heads and 4" crank, rotators valves. Searched and can't find anything about it.
|
03-27-2021, 10:10 PM | #15 |
Senior Member
Join Date: May 2010
Location: Chester Vt
Posts: 8,860
|
Re: 53 cam for auto
I would deffinately bore to 3 5/16. this will at aprox 20 ci and a poiin compression. Best cam would be a 52/53 EAB stock cam, which was made for the auto.
Gramps |
03-27-2021, 10:18 PM | #16 | |
Junior Member
Join Date: Jan 2019
Posts: 3
|
Re: 53 cam for auto
Quote:
|
|
03-27-2021, 10:36 PM | #17 | |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,316
|
Re: 53 cam for auto
Quote:
I am now aware of 4 distinctly different 8BA type cams : (8BA, 8CM, 1CM, and EAB). There may be more. It sure would be nice if someone could find the definitive specifications for these (and any others). It would be an interesting comparison. |
|
03-28-2021, 12:40 AM | #18 |
Senior Member
Join Date: Sep 2011
Location: Christchurch New Zealand
Posts: 1,611
|
Re: 53 cam for auto
As per JDL 08-10-2010.
Cam Specs. Default Re: 53 Mercury camshaft 49-51 ford "B" cam .305 lift int. opens 5*btc - closes44*abc set.017 exh. opens 48*bbc -closes3*atc set.019 52-53 ford "E" EAB cam .328 lift int. opens 21*btc - closes68*abc set.017 exh. opens 56*bbc - closes11*atc set.019 49-50 merc "8CM" cam .338 lift int. opens 10*btc - closes50*abc set.014 exh. opens 50*bbc - closes10*atc set.016 51-53 merc "1CM" cam .333 lift int. opens 5*btc - closes51* abc set.017 exh. opens 47*bbc - closes9* atc set.019 I used the above as a reference along with Tilden Specs. I settled upon a NOS 1CM cam for a stroker engine 285cu". Phil NZ |
03-28-2021, 05:58 AM | #19 |
Senior Member
Join Date: Jul 2010
Location: Rochester, NY
Posts: 266
|
Re: 53 cam for auto
Is the EAB duration really 20* more for intake than exhaust?
|
03-28-2021, 12:01 PM | #20 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,316
|
Re: 53 cam for auto
Thanks Phil, that's good information. It looks like the 1CM was detuned slightly from the 8CM as I guessed. One minor question; did the '52-'53 mercury's use the 1CM cam or was there a separate "EAC" cam for them? Also, is there such a thing as an "8RT" cam?
Looks like the 8CM is the "best" stock for cam given the information we have (the highest lift, at least). |
|
|
Sponsored Links (Register now to hide all advertisements) |
|