|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
11-14-2016, 07:28 PM | #1 |
Senior Member
Join Date: Apr 2016
Location: Bellingham, WA
Posts: 1,163
|
Engine + Trans Install
Is it possible...if so are there any tricks...to installing the engine and transmission as a unit?
__________________
All steel from pedal to wheel |
11-14-2016, 07:34 PM | #2 |
BANNED
Join Date: May 2012
Location: inside your RAM
Posts: 3,134
|
Re: Engine + Trans Install
yep
done it several times old timer showed me. at least with a stock head, it was strong enough to put your lifting eye in hole #3, gives perfect balance. there have been some on here that said they tried that with a repop head and the head broke apart
__________________
'31 180A |
Sponsored Links (Register now to hide all advertisements) |
|
11-14-2016, 07:40 PM | #3 |
Senior Member
Join Date: May 2010
Location: Central, IL
Posts: 3,968
|
Re: Engine + Trans Install
I dont like the idea of $2000 hanging by a single spark plug hole, I used several straps (4 i think)the first time, 2nd time I used #1 and 4 holes and lifted above the 3, I also had to use a chain around the lower water neck up to my lifting hook to keep it level side to side.
Its OK if it tilts back a little - your gonna want that to line up the U joint. Should slip right on. You may have to lower it till the front motor mount is just about ready to touch the oil pan to get it to slip on. DO NOT stick your fingers in there to help align the U joint - it will slip on and crush your fingers faster than you think. Use tools or wood sticks.
__________________
1929 Model AA - Need long splash aprons! |
11-14-2016, 07:41 PM | #4 |
Senior Member
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,496
|
Re: Engine + Trans Install
I've done it with a repo head but I don't use the hook arrangement in #3. I use a couple of ropes tied off separately. One goes behind the crank pulley, the other between the back of the sump and the flywheel housing.
Now for a word of warning: When you align the spline in the universal with the drive shaft, DON'T put your fingers in there. When they line up, they can slide together very quickly and with enough force that the ends of your fingers will be left in there. It might take a little fiddling but I use a screw driver and pointy nosed pliers - what ever works. I want to keep my fingers coz I like to scratch when it itches.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood. |
11-14-2016, 09:32 PM | #5 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Engine + Trans Install
With the body off I install them together, but with the body on I've always installed them separately.
|
11-15-2016, 07:12 PM | #6 |
Senior Member
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,390
|
Re: Engine + Trans Install
Sponsored Links (Register now to hide all advertisements)
Are you sure. I used a 1/2 ton chainfall when I put the olds in my deuce coupe............. Paul in CT |
11-15-2016, 07:15 PM | #7 |
Senior Member
Join Date: Apr 2016
Location: Bellingham, WA
Posts: 1,163
|
Re: Engine + Trans Install
I think he said $2000. It's a good thing I'm well under that
__________________
All steel from pedal to wheel |
11-15-2016, 07:16 PM | #8 |
Senior Member
Join Date: May 2010
Location: Stayton, Oregon
Posts: 3,806
|
Re: Engine + Trans Install
There was a $ on that 2000. Think the engine and tranny is only 500 to 600 lbs. So your 1/2 ton will work.
__________________
Fred Kroon 1929 Std Coupe 1929 Huckster |
11-15-2016, 07:22 PM | #9 |
Senior Member
Join Date: May 2010
Location: Maryville, TN
Posts: 491
|
Re: Engine + Trans Install
I have used the #1 & #3 spark plug holes with a Chinese leveler that I bought years ago. It really makes the job easier. I think that H-F still sells them. I used a 1 ton cherry picker.
Vic |
11-15-2016, 08:37 PM | #10 |
BANNED
Join Date: Feb 2013
Location: Coatesville, Pa
Posts: 719
|
Re: Engine + Trans Install
I have used a leveler but had ropes going around the engine. Got it over the light bar then in on a steep angle. Get the transmission just below the fire wall then level it out and push it on in. Having a helper helps.
|
11-15-2016, 08:49 PM | #11 | |
Senior Member
Join Date: Apr 2016
Location: Bellingham, WA
Posts: 1,163
|
Re: Engine + Trans Install
Quote:
__________________
All steel from pedal to wheel |
|
11-15-2016, 10:08 PM | #12 |
BANNED
Join Date: May 2012
Location: inside your RAM
Posts: 3,134
|
Re: Engine + Trans Install
Dick, that s/b a cake walk
might even want to remove the front yoke for now, too
__________________
'31 180A |
11-15-2016, 10:55 PM | #13 |
Senior Member
Join Date: Jul 2012
Location: Venice, FL
Posts: 648
|
Re: Engine + Trans Install
Our club installed an engine this year complete with clutch, housings and tranny all assembled. Body on. The frame had to be spread a little in the process. Make sure the throttle linkage is removed from the flywheel housing and the screw type lifting bracket is a dream for this job.
Al |
11-15-2016, 11:07 PM | #14 |
Senior Member
Join Date: May 2010
Location: Central, IL
Posts: 3,968
|
Re: Engine + Trans Install
the pedals and steering column can be a bear to work around FYI. once again keep your fingers away from anything that can pinch.
__________________
1929 Model AA - Need long splash aprons! |
11-15-2016, 11:42 PM | #15 | |
Senior Member
Join Date: Apr 2016
Location: Bellingham, WA
Posts: 1,163
|
Re: Engine + Trans Install
Quote:
Thanks for the tip!
__________________
All steel from pedal to wheel |
|
11-15-2016, 11:43 PM | #16 | |
Senior Member
Join Date: Apr 2016
Location: Bellingham, WA
Posts: 1,163
|
Re: Engine + Trans Install
Quote:
Throttle linkage is off. I have an adjustable lifting bracket but I've always had better luck NOT using them. I might give it another try.
__________________
All steel from pedal to wheel |
|
11-15-2016, 11:44 PM | #17 |
Senior Member
Join Date: Apr 2016
Location: Bellingham, WA
Posts: 1,163
|
Re: Engine + Trans Install
Pedals are off the bell. I'll install them when the lump is in place.
__________________
All steel from pedal to wheel |
11-16-2016, 07:48 AM | #18 |
Senior Member
Join Date: May 2010
Location: Central, IL
Posts: 3,968
|
Re: Engine + Trans Install
ahh good, yea should be a cakewalk then. Just don't forget the turtle that covers the u joint before you slip it together. And the gaskets...
__________________
1929 Model AA - Need long splash aprons! |
11-16-2016, 10:45 AM | #19 |
Senior Member
Join Date: Mar 2016
Location: Lynden, WA
Posts: 1,564
|
Re: Engine + Trans Install
I like cake! I'll be there! I'll bring my BIG hammer.
|
11-16-2016, 10:49 AM | #20 |
Senior Member
Join Date: Apr 2016
Location: Bellingham, WA
Posts: 1,163
|
Re: Engine + Trans Install
Does cake go OK with beer?
__________________
All steel from pedal to wheel |
|
|
Sponsored Links (Register now to hide all advertisements) |
|