Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 03-25-2020, 01:26 AM   #1
dumb person
Senior Member
 
dumb person's Avatar
 
Join Date: Apr 2011
Location: South pacific island
Posts: 1,724
Question Would there be any interest in a programmable electronic points replacer?

I know lots of you (including myself) like the simplicity of the original system. So i'd design something that was about 5 minutes work to swap back to how the model A should be.


While tinkering with electronic ignition i found i can make a very simple system for the model A with programmable advance. You could dial back the advance for high compression heads, or add a small potentiometer to the carb' for maximum fuel economy. A simple D.I.Y. device you too can make at home.
It could be as simple as a tiny box on the firewall under one of the coil fastener clamps.


Or if you have more resources you could make something that replaces the points cam (although i'd rather leave the points cam and make a points plate without points)
My current set up only works well on 9 or more volts.

So before i order parts online & hope they come (if i have spare time, hopefully i will, considering...)
__________________
<Link> This is how we roll<Link>

"I'm Convinced that no one really reads posts anymore; they just fabricate what they think the post says then ramble on about red herrings."--Bob
Outcasts rules of old cars
#1 Fun is imperative, mainstream is overrated
#2 If they think it is impossible, prove them wrong
#3 If the science says it impossible you are not being creative enough.
#4 No shame in recreating something you never had
#5 If it were not for the law & physics you would be unstoppable
dumb person is offline   Reply With Quote
Old 03-25-2020, 02:51 AM   #2
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,475
Default Re: Would there be any interest in a programmable electronic points replacer?

So I guess 9 volts or more means a car already converted to 12 v is a prime candidate. Given how fussy my phaeton is about ignition timing, I'd be interested in more info like $.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-25-2020, 08:44 AM   #3
Jack Shaft
BANNED
 
Join Date: Dec 2019
Posts: 1,196
Default Re: Would there be any interest in a programmable electronic points replacer?

Advance mapping for model a ford engines is simple,1 degree advance per 100 rpm fits the bill.Raising compression does not change that basic parameter,in fact,advancing above that for high compression can cause damage.
Jack Shaft is offline   Reply With Quote
Old 03-25-2020, 09:59 AM   #4
MikeK
Senior Member
 
MikeK's Avatar
 
Join Date: May 2010
Location: Windy City
Posts: 2,919
Default Re: Would there be any interest in a programmable electronic points replacer?

Adding a potentiometer (throttle position sensor) to a carburetor will be of little value without extensive mapping of a specific engine build because it would not be independent of fuel metering/lambda/lean/rich.

What is really needed is a MAP sensor input so you could have a selection of vacuum advance/retard profiles over selectable RPM advance tables. (A generic MAP sensor is about $25) That would give you excellent economy cruise and quickly compensate for variable engine load while accelerating, going uphill, etc.

Missing from all the points replacement systems and modules for older Kettering ignition vehicles is a time-out system to prevent current drain if the engine is stopped with the dizzy cam sensor in the old 'points closed' position. Not only does this prevent the coil from cooking due to 100% dwell saturation time, it keeps your output switching MOSFET from getting smoking hot on its heat sink and possibly failing. Easy to do- output gate clamped via a simple timer until the cam sensor delivers pulses less than a few seconds apart.

Last edited by MikeK; 03-25-2020 at 10:16 AM.
MikeK is offline   Reply With Quote
Old 03-25-2020, 10:42 AM   #5
Flathead
Senior Member
 
Flathead's Avatar
 
Join Date: May 2010
Location: Southern Maine
Posts: 1,494
Default Re: Would there be any interest in a programmable electronic points replacer?

Or......you could use mechanical points.
Flathead is offline   Reply With Quote
Old 03-25-2020, 10:48 AM   #6
MikeK
Senior Member
 
MikeK's Avatar
 
Join Date: May 2010
Location: Windy City
Posts: 2,919
Default Re: Would there be any interest in a programmable electronic points replacer?

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Flathead View Post
Or......you could use mechanical points.
Totally agree!
MikeK is offline   Reply With Quote
Old 03-25-2020, 11:40 AM   #7
California Travieso
Senior Member
 
Join Date: Mar 2014
Location: Moreno Valley, CA
Posts: 941
Send a message via Yahoo to California Travieso
Default Re: Would there be any interest in a programmable electronic points replacer?

Quote:
Originally Posted by MikeK View Post
Adding a potentiometer (throttle position sensor) to a carburetor will be of little value without extensive mapping of a specific engine build because it would not be independent of fuel metering/lambda/lean/rich.

What is really needed is a MAP sensor input so you could have a selection of vacuum advance/retard profiles over selectable RPM advance tables. (A generic MAP sensor is about $25) That would give you excellent economy cruise and quickly compensate for variable engine load while accelerating, going uphill, etc.

Missing from all the points replacement systems and modules for older Kettering ignition vehicles is a time-out system to prevent current drain if the engine is stopped with the dizzy cam sensor in the old 'points closed' position. Not only does this prevent the coil from cooking due to 100% dwell saturation time, it keeps your output switching MOSFET from getting smoking hot on its heat sink and possibly failing. Easy to do- output gate clamped via a simple timer until the cam sensor delivers pulses less than a few seconds apart.

Can I get an app for that?

David Serrano
California Travieso is offline   Reply With Quote
Old 03-25-2020, 01:59 PM   #8
Jacksonlll
Senior Member
 
Jacksonlll's Avatar
 
Join Date: Jul 2012
Location: Michigan-- Member of Oakleaf of MARC
Posts: 1,686
Send a message via ICQ to Jacksonlll
Default Re: Would there be any interest in a programmable electronic points replacer?

The problem with getting away from standard is that when you break down on a tour, your buddies can’t help you. You better have a spare you can put on, or be able to fix it yourself. 8
Jacksonlll is offline   Reply With Quote
Old 03-25-2020, 03:04 PM   #9
nomadpsd
Member
 
nomadpsd's Avatar
 
Join Date: Jul 2018
Posts: 49
Default Re: Would there be any interest in a programmable electronic points replacer?

I would be interested. I talked to a company at the SEMA show last year that is making programmable distributors for 60's V8's. He said he could probably make one for a Model A, but it would be in a V8 housing. Not ideal. The MAP sensor input would be a must. Running a Zipper now, but would be great to be able to have the retard feature under load.
nomadpsd is offline   Reply With Quote
Old 03-29-2020, 04:41 AM   #10
dumb person
Senior Member
 
dumb person's Avatar
 
Join Date: Apr 2011
Location: South pacific island
Posts: 1,724
Default Re: Would there be any interest in a programmable electronic points replacer?

Quote:
Originally Posted by Flathead View Post
Or......you could use mechanical points.
Well, yes. Points are resistant to EMP, nuclear fallout, and polarity. But i've been there done that.

I did get it working on 6 volts with some trickery
But then the microcomputer died from voltage spikes.

I'll defeat this puzzle somehow...
__________________
<Link> This is how we roll<Link>

"I'm Convinced that no one really reads posts anymore; they just fabricate what they think the post says then ramble on about red herrings."--Bob
Outcasts rules of old cars
#1 Fun is imperative, mainstream is overrated
#2 If they think it is impossible, prove them wrong
#3 If the science says it impossible you are not being creative enough.
#4 No shame in recreating something you never had
#5 If it were not for the law & physics you would be unstoppable
dumb person is offline   Reply With Quote
Old 03-29-2020, 04:42 AM   #11
dumb person
Senior Member
 
dumb person's Avatar
 
Join Date: Apr 2011
Location: South pacific island
Posts: 1,724
Default Re: Would there be any interest in a programmable electronic points replacer?

Quote:
Originally Posted by Jacksonlll View Post
The problem with getting away from standard is that when you break down on a tour, your buddies can’t help you. You better have a spare you can put on, or be able to fix it yourself. 8
With the 12 volt prototype i made, you wouldn't need a spare. You'd just bypass it & use the points as per factory. It was using the points as a reference to cam' position.
__________________
<Link> This is how we roll<Link>

"I'm Convinced that no one really reads posts anymore; they just fabricate what they think the post says then ramble on about red herrings."--Bob
Outcasts rules of old cars
#1 Fun is imperative, mainstream is overrated
#2 If they think it is impossible, prove them wrong
#3 If the science says it impossible you are not being creative enough.
#4 No shame in recreating something you never had
#5 If it were not for the law & physics you would be unstoppable
dumb person is offline   Reply With Quote
Old 03-29-2020, 09:58 AM   #12
Badpuppy
Senior Member
 
Join Date: Dec 2017
Location: Guthrie, OK
Posts: 1,142
Default Re: Would there be any interest in a programmable electronic points replacer?

Along with MikeK's suggestions, you should add a knock sensor for optimum spark advance at all times.

Back in the day I put a points eliminator setup on my '74 Mustang V6. IR sensor across the cam lobes (with adapter) switched a transistor to drive the coil. No more burned points or worn rubbing block. Worked great until I sold it in '81.

Yeah, those 6 volts are a PIA, especially the negative ones.

Last edited by Badpuppy; 03-29-2020 at 10:43 AM.
Badpuppy is offline   Reply With Quote
Old 03-29-2020, 04:25 PM   #13
lsr490
Member
 
Join Date: May 2012
Location: RTP North Carolina
Posts: 68
Default Re: Would there be any interest in a programmable electronic points replacer?

Has anyone looked at this http://www.kirkengines.com/index.php#1 ?
I have two on hand and looking to install one here shortly.
__________________
"Avoid Model A Mythsteries. Read, study and challenge ALL advice with current logic, chemistry and technology!" author unknown
lsr490 is offline   Reply With Quote
Old 03-29-2020, 05:48 PM   #14
California Travieso
Senior Member
 
Join Date: Mar 2014
Location: Moreno Valley, CA
Posts: 941
Send a message via Yahoo to California Travieso
Default Re: Would there be any interest in a programmable electronic points replacer?

Quote:
Originally Posted by lsr490 View Post
Has anyone looked at this http://www.kirkengines.com/index.php#1 ?
I have two on hand and looking to install one here shortly.
The product description states that the coil should be 3+ ohms: “The use of . . . coils with resistance values lower than 3.0 ohms will cause the module to fail.”

It looks like you’re ok if you have converted to a 12 volt system but those of us with original 6 volt systems may not be able to use it.

Unless the the electricity gurus on the Ford Barn can suggest a workaround, it may be worthwhile to bite the bullet and convert to a 12 volt system. Too bad I just bought a new 6 volt battery.

I’m interested to hear what your experience is.

David Serrano
California Travieso is offline   Reply With Quote
Old 03-29-2020, 06:12 PM   #15
California Travieso
Senior Member
 
Join Date: Mar 2014
Location: Moreno Valley, CA
Posts: 941
Send a message via Yahoo to California Travieso
Default Re: Would there be any interest in a programmable electronic points replacer?

Quote:
Originally Posted by lsr490 View Post
Has anyone looked at this http://www.kirkengines.com/index.php#1 ?
I have two on hand and looking to install one here shortly.
The product description states that the coil should be 3+ ohms: “The use of . . . coils with resistance values lower than 3.0 ohms will cause the module to fail.”

You’re ok if you have converted to a 12 volt system but those of us with original 6 volt systems may not be able to use it.

Unless the the electricity gurus on the Ford Barn can suggest a workaround, it may be worthwhile to bite the bullet and convert to a 12 volt system. Too bad I just bought a new 6 volt battery.

I’m interested to hear what your experience is.

David Serrano
California Travieso is offline   Reply With Quote
Old 03-29-2020, 06:13 PM   #16
MikeK
Senior Member
 
MikeK's Avatar
 
Join Date: May 2010
Location: Windy City
Posts: 2,919
Default Re: Would there be any interest in a programmable electronic points replacer?

Quote:
Originally Posted by lsr490 View Post
Has anyone looked at this http://www.kirkengines.com/index.php#1 ?
I have two on hand and looking to install one here shortly.
The original post of this thread was for a system to add ignition advance. This device does not do that.

Among the multitude of devices designed to replace capacitive resonance(the condenser) with a single sharp field collapse in the coil ('transistor switching'), this one is the worst I have seen.

Here is what is inside:
Since this is not an electronics forum I won't go in excessive detail, but if you get a dozen 30 minute trips in a Model A with this in the distributor it will be a miracle. It was designed (poorly!) for a lawn mower.

Even the manufacturer's install instructions tell you very bad things about the design:
"Operation with a poor or non-existing ground can instantly destroy this device when power is applied!" (You need a dedicated ground to the battery in a Model A)

" Do not mount in the breaker points box as overheating and subsequent failure will occur!" (breaker points box on a lawn mower is equivalent to the distributor on a Model A, a HOT place!)

Good luck with it!
MikeK is offline   Reply With Quote
Old 03-30-2020, 04:20 AM   #17
rally 1
Senior Member
 
Join Date: Aug 2010
Location: Cleveland, Ohio
Posts: 170
Default Re: Would there be any interest in a programmable electronic points replacer?

Check out MSD #8680, adjustable timing control
rally 1 is offline   Reply With Quote
Old 03-30-2020, 02:10 PM   #18
MikeK
Senior Member
 
MikeK's Avatar
 
Join Date: May 2010
Location: Windy City
Posts: 2,919
Default Re: Would there be any interest in a programmable electronic points replacer?

Quote:
Originally Posted by rally 1 View Post
Check out MSD #8680, adjustable timing control
That device provides MANUAL control just like the advance lever on an A. Additionally, it only has a 15 degree range. The O.P. ('dumb person') wants to automate that function.
MikeK is offline   Reply With Quote
Old 04-13-2020, 01:39 AM   #19
dumb person
Senior Member
 
dumb person's Avatar
 
Join Date: Apr 2011
Location: South pacific island
Posts: 1,724
Default Re: Would there be any interest in a programmable electronic points replacer?

The model T programming wasn't playing nice on a single cylinder, and for some reason decided microseconds wasn't going to work anymore.

So i made do with milliseconds.
So close to making a simple module that bolts across the 2 coil posts...
It was even working on both 6 and 12 volts.


https://youtu.be/9YYLSqjWV9s


But then the pro-micro died from me trying to make it use shared ground/power with the coil & battery.
Hmm.... At least the coding side is getting closer.
__________________
<Link> This is how we roll<Link>

"I'm Convinced that no one really reads posts anymore; they just fabricate what they think the post says then ramble on about red herrings."--Bob
Outcasts rules of old cars
#1 Fun is imperative, mainstream is overrated
#2 If they think it is impossible, prove them wrong
#3 If the science says it impossible you are not being creative enough.
#4 No shame in recreating something you never had
#5 If it were not for the law & physics you would be unstoppable
dumb person is offline   Reply With Quote
Old 04-13-2020, 08:58 AM   #20
McMimmcs
Senior Member
 
McMimmcs's Avatar
 
Join Date: Sep 2019
Location: Fort Gratiot, Michigan
Posts: 2,296
Default Re: Would there be any interest in a programmable electronic points replacer?

With all due respect I ask what will be the significant advantage over what Henry used in his cars. Regular points are simple to install, maintain and very inexpensive. Why try to reinvent the wheel?
McMimmcs is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:29 AM.