Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 01-06-2015, 07:59 AM   #41
Flysafe
Member
 
Join Date: Sep 2013
Location: Lisboa / Portugal
Posts: 43
Default Re: Oil pan 59AB photos

Hello all,


Some progress in the drawing, left side block, the lines of the back is not done yet. Now they are aligned.

All the best,
Jorge
Attached Images
File Type: jpg Bloco Motor 099.jpg (33.8 KB, 77 views)
Flysafe is offline   Reply With Quote
Old 01-24-2015, 03:41 PM   #42
Flysafe
Member
 
Join Date: Sep 2013
Location: Lisboa / Portugal
Posts: 43
Default Re: Oil pan 59AB photos

I need some help, which side have the bigger angle in the valves?
Flysafe is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 01-24-2015, 04:25 PM   #43
JSeery
Senior Member
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 13,208
Default Re: Oil pan 59AB photos

Are you looking for the angles? 52.09 on the left and 49.36 on the right.
Attached Images
File Type: jpg Ford-V8-X-section.jpg (49.8 KB, 52 views)
JSeery is offline   Reply With Quote
Old 01-26-2015, 08:02 AM   #44
Flysafe
Member
 
Join Date: Sep 2013
Location: Lisboa / Portugal
Posts: 43
Default Re: Oil pan 59AB photos

Thank you .
Flysafe is offline   Reply With Quote
Old 02-01-2015, 10:31 AM   #45
Flysafe
Member
 
Join Date: Sep 2013
Location: Lisboa / Portugal
Posts: 43
Default Re: Oil pan 59AB photos

Hello all,

Now with a few more things, the funny part will begin, extrude all the lines.
The valves sets is done with the correct angle. I will need to resize some parts not serious.


Flysafe is offline   Reply With Quote
Old 02-04-2015, 07:57 AM   #46
Flysafe
Member
 
Join Date: Sep 2013
Location: Lisboa / Portugal
Posts: 43
Default Re: Oil pan 59AB photos

Does anyone has a piston for a bore 3.1875 that can take a measurement?
-Height,
-From the bottom to the middle of the piston pin,
-The pin diameter.

Thank you so much.
Flysafe is offline   Reply With Quote
Old 02-04-2015, 11:33 AM   #47
JSeery
Senior Member
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 13,208
Default Re: Oil pan 59AB photos

See if any of this helps. This piston is from a 1948 59a engine, it is domed top, 3.188 +.040 (original 3.188 bored std .040 over).

From top edge of piston to bottom of longest part of skirt: 2.960
From top edge of piston to bottom of shortest part of skirt: 2.700 (not including notch)
Width of longest part of skirt: ~1.250
Width of shortest part of skirt: ~1.250
It is curved between these sections.
From top edge of piston to top of dome: ~.250

Starting a top edge of piston working down to shortest part of skirt (not including notch).
Top edge to top piston ring: .250
Top piston ring grove: .096
Top piston ring to second piston ring: .156
Second piston ring grove: .096
Second piston ring to third piston ring: .100
Third piston ring grove: .188
Third piston ring to top of piston pin: .268
Piston pin: .750
Bottom of piston pin to bottom piston ring: .170
Bottom piston ring grove: .183
Bottom piston ring to bottom of skirt: .440 (not including notch)

From Top edge of piston to center of piston pin: ~1.530
From center of piston pin to bottom of skirt: ~1.170
Piston Pin diameter: .750

These are measurements straight from a piston using calipers and include measuring errors I am sure!

Last edited by JSeery; 02-04-2015 at 10:01 PM.
JSeery is offline   Reply With Quote
Old 02-04-2015, 11:35 AM   #48
JSeery
Senior Member
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 13,208
Default Re: Oil pan 59AB photos

For some reason the photos didn't load the first time.
Attached Images
File Type: jpg 20150204_100802.jpg (55.6 KB, 17 views)
File Type: jpg 20150204_094728.jpg (44.3 KB, 13 views)
JSeery is offline   Reply With Quote
Old 02-05-2015, 06:44 AM   #49
Flysafe
Member
 
Join Date: Sep 2013
Location: Lisboa / Portugal
Posts: 43
Default Re: Oil pan 59AB photos

Thank you so much JSeery.
Flysafe is offline   Reply With Quote
Old 02-05-2015, 10:22 AM   #50
Flysafe
Member
 
Join Date: Sep 2013
Location: Lisboa / Portugal
Posts: 43
Default Re: Oil pan 59AB photos

Earlier I do this type of piston, can be used in this engine model?
Attached Images
File Type: jpg Bloco Motor 103.jpg (13.6 KB, 19 views)
File Type: jpg Bloco Motor 102.jpg (14.6 KB, 12 views)
Flysafe is offline   Reply With Quote
Old 02-05-2015, 11:03 AM   #51
JSeery
Senior Member
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 13,208
Default Re: Oil pan 59AB photos

There are 3 ring and 4 ring pistons. I believe the original design from Ford was the 4 ring and the 3 ring was a more modern replacement. Not sure it would make any difference for what you are doing, a lot of the current rebuilds use the 3 ring style.
JSeery is offline   Reply With Quote
Old 02-06-2015, 07:06 AM   #52
Flysafe
Member
 
Join Date: Sep 2013
Location: Lisboa / Portugal
Posts: 43
Default Re: Oil pan 59AB photos

Thanks.
Flysafe is offline   Reply With Quote
Old 02-08-2015, 09:30 AM   #53
Flysafe
Member
 
Join Date: Sep 2013
Location: Lisboa / Portugal
Posts: 43
Default Re: Oil pan 59AB photos

Hello all,

Some of the lines after extruder.
Attached Images
File Type: jpg Bloco Motor 105.jpg (23.9 KB, 27 views)
File Type: jpg Bloco Motor 106.jpg (21.8 KB, 22 views)
Flysafe is offline   Reply With Quote
Old 03-25-2015, 04:53 PM   #54
Flysafe
Member
 
Join Date: Sep 2013
Location: Lisboa / Portugal
Posts: 43
Default Re: Oil pan 59AB photos

Some progress in the design.
Attached Images
File Type: jpg Bloco Motor 108.jpg (27.0 KB, 23 views)
File Type: jpg Bloco Motor 109.jpg (40.2 KB, 27 views)
Flysafe is offline   Reply With Quote
Old 03-30-2015, 11:42 AM   #55
Flysafe
Member
 
Join Date: Sep 2013
Location: Lisboa / Portugal
Posts: 43
Default Re: Oil pan 59AB photos

Hello all,

Exhaust channels done, and e few holes. Start the front end of the block.
Attached Images
File Type: jpg Bloco Motor 110.jpg (26.1 KB, 30 views)
File Type: jpg Bloco Motor 113.jpg (29.9 KB, 27 views)

Last edited by Flysafe; 03-30-2015 at 11:53 AM.
Flysafe is offline   Reply With Quote
Old 04-06-2015, 10:44 AM   #56
Flysafe
Member
 
Join Date: Sep 2013
Location: Lisboa / Portugal
Posts: 43
Default Re: Oil pan 59AB photos

Hello all,

The 59 AB block have the yellow line that I made?
The block 8 BA have this fill.

Thank you so much.
Attached Images
File Type: jpg Bloco Motor 118.jpg (35.1 KB, 34 views)
Flysafe is offline   Reply With Quote
Old 04-07-2015, 12:15 PM   #57
Flysafe
Member
 
Join Date: Sep 2013
Location: Lisboa / Portugal
Posts: 43
Default Re: Oil pan 59AB photos

Hello all,

I 'm working in the front end of the block, I will need some help, someone have any photos where I can see the front end of the block 59 AB without the water pumps and the distributor cover? I already made a google search but not find anything.

Thank you so much for the help.

All the best,
Jorge
Flysafe is offline   Reply With Quote
Old 04-07-2015, 12:51 PM   #58
JSeery
Senior Member
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 13,208
Default Re: Oil pan 59AB photos

I can add some in about an hour.
JSeery is offline   Reply With Quote
Old 04-08-2015, 05:17 AM   #59
Flysafe
Member
 
Join Date: Sep 2013
Location: Lisboa / Portugal
Posts: 43
Default Re: Oil pan 59AB photos

Quote:
Originally Posted by JSeery View Post
I can add some in about an hour.

Thank you so much JSeery
Flysafe is offline   Reply With Quote
Old 04-08-2015, 11:44 AM   #60
JSeery
Senior Member
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 13,208
Default Re: Oil pan 59AB photos

I'm easily distracted! But here are 4 shots of 59a block. This is a 48 block (as far as I know) out of a Truck.
Attached Images
File Type: jpg 59a block front 1.jpg (58.4 KB, 25 views)
File Type: jpg 59a block front 2.jpg (57.3 KB, 25 views)
File Type: jpg 59a block front 3.jpg (54.0 KB, 20 views)
File Type: jpg 59a block front 4.jpg (63.5 KB, 22 views)
JSeery is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:03 AM.