Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 07-10-2020, 09:12 AM   #1
skidmarks
Senior Member
 
skidmarks's Avatar
 
Join Date: Aug 2010
Location: newark, delaware
Posts: 3,557
Default Ford factory / dealer service tool

Anyone know what its for. Im guessing 1960s era

Has fomoco and a part number
Attached Images
File Type: jpg 138649.jpg (34.5 KB, 51 views)
File Type: jpg 138650.jpg (49.9 KB, 42 views)
File Type: jpg 138651.jpg (46.4 KB, 46 views)
File Type: jpg 138648.jpg (47.4 KB, 41 views)
skidmarks is offline   Reply With Quote
Old 07-10-2020, 09:25 AM   #2
RalphM
Senior Member
 
RalphM's Avatar
 
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,534
Default Re: Ford factory / dealer service tool

Transmission band adjustment tool.
RalphM is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 07-10-2020, 09:26 AM   #3
VeryTangled
Senior Member
 
VeryTangled's Avatar
 
Join Date: May 2010
Location: (Not far enough...) Outside of DC
Posts: 2,802
Default Re: Ford factory / dealer service tool

Hi Everyone! Skidmarks it seems to be a holding tool and thickness gauge for late 50's early 60's Ford 2 speed automatic transmission..

Referenced here: https://www.jalopyjournal.com/forum/...-matic.990213/

And here: https://www.fixya.com/cars/t15136643...park_1962_ford

Attached Images
File Type: jpg Capture.JPG (34.4 KB, 159 views)
__________________
-Jeff

Last edited by VeryTangled; 07-10-2020 at 10:14 AM.
VeryTangled is offline   Reply With Quote
Old 07-10-2020, 09:33 AM   #4
Bob C
Senior Member
 
Join Date: May 2010
Location: So Cal
Posts: 7,067
Default Re: Ford factory / dealer service tool

Did a search and it looks like it is for adjusting the rear band on transmission.
http://restorecarsclassifieds.com/wi...df.pdf?n=15424
Bob C is offline   Reply With Quote
Old 07-10-2020, 09:41 AM   #5
skidmarks
Senior Member
 
skidmarks's Avatar
 
Join Date: Aug 2010
Location: newark, delaware
Posts: 3,557
Default Re: Ford factory / dealer service tool

Thank you
skidmarks is offline   Reply With Quote
Old 07-10-2020, 09:50 AM   #6
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 7,148
Default Re: Ford factory / dealer service tool

Sponsored Links (Register now to hide all advertisements)
It's for: COMET, EDSEL, FALCON Ford 2-Speed Auto Trans 1959-60.


Copied and pasted:


Rear Band (Reverse Range): Drain transmission and remove oil pan and screen. Loosen rear servo piston rodlocknut and adjusting nut, then install tool as follows:If Ford Tool T59P-77409-A used, place tool on rearservo rod so two forks straddle band apply lever.NOTE The inner fork must engage flat on servo pist nrod. The outer fork is a %" spacer and must be insertedbetween piston rod seat and adjusting nut. If Edsel Tool7355-A used, insert tool between adjusting nut andpiston rod-to-actuating lever seat, with opposite endof tool resting on raised boss on control valve assembly.With wrench T59P-77423-A (Ford), or No. 7355-B(Edsel),tighten adjusting nut until wrench handle snaps (breaks)over center. NOTE - These tools are pre-set torquewrenches which overrun when torque on screw reaches45-50 inch pounds. Back off adjusting nut exactly twtums. Hold adjusting nut at this position and tightenlocknut to 15-18 ft. lbs. Remove tools from servo pistonrod. Install oil pan and screen using a new gasket. Filltransmission with Automatic Transmission Fluid Type"A"


You can buy another one "NOW" on eBay for $29.41. DD
__________________
T5 W/TORQUE TUBE


There are TWO types of people in this world.
___________________________________
1) Those who CAN extrapolate from incomplete data....


V8COOPMAN is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:39 PM.