Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 08-11-2019, 02:37 PM   #1
[email protected]
Member
 
Join Date: Jun 2018
Posts: 47
Default valve clearence

reminder on what the Model a valve clearance is . thanks, steve
steveankc@gmail.com is offline   Reply With Quote
Old 08-11-2019, 02:52 PM   #2
J Franklin
Senior Member
 
J Franklin's Avatar
 
Join Date: May 2010
Location: Oregon
Posts: 5,946
Default Re: valve clearence

Many answers depending where you find it. I set mine intake at .010 and exhaust at .012, no closer.
J Franklin is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 08-11-2019, 03:18 PM   #3
Richard in Anaheim CA
Senior Member
 
Richard in Anaheim CA's Avatar
 
Join Date: May 2010
Location: Anaheim California
Posts: 551
Default Re: valve clearence

There were 4 changes in 1928 in the service bulletins.

I set mine at .010 intake and .013 exhaust.

RICHARD
ANAHEIM CA
Richard in Anaheim CA is offline   Reply With Quote
Old 08-11-2019, 06:29 PM   #4
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,471
Default Re: valve clearence

Depends on what the valves are made of. I recently had a camshaft reground and the people who did it said 0.025" on the exhaust with stainless valves. I settled on 0.022" and all has been well. Noisy while the motor is cold but quieten right down as it warms up.
He told of a guy who had put stainless valves in his Model T and set the clearances as per spec. When things weren't working out, an inspection of the camshaft showed that the followers were rubbing the heel of the cam - hard. They opened the gap to 0.025" and all has been well there too.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Old 08-11-2019, 08:54 PM   #5
J Franklin
Senior Member
 
J Franklin's Avatar
 
Join Date: May 2010
Location: Oregon
Posts: 5,946
Default Re: valve clearence

Always follow the rebuilders recommendation, but he was asking about Model A specs. Modified engines need to be looked at carefully.
J Franklin is offline   Reply With Quote
Old 08-12-2019, 01:20 AM   #6
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,471
Default Re: valve clearence

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by J Franklin View Post
Always follow the rebuilders recommendation, but he was asking about Model A specs. Modified engines need to be looked at carefully.
Wise advice but how many Model As are running original valves? If they have been replaced with modern steels, things change.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Old 08-12-2019, 07:18 AM   #7
[email protected]
Member
 
Join Date: Jun 2018
Posts: 47
Default Re: valve clearence

what makes the valves noisy to loose or to tight? these are stock valves, old school
steveankc@gmail.com is offline   Reply With Quote
Old 08-12-2019, 08:12 AM   #8
100IH
Senior Member
 
Join Date: Dec 2011
Location: SW Idaho
Posts: 970
Default Re: valve clearence

Too loose makes noisey
100IH is offline   Reply With Quote
Old 08-12-2019, 08:56 AM   #9
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: valve clearence

Well, if everything is stock then the valves are not adjustable. At least they are not easily adjusted, to adjust the originals the stem requires grinding or seats need cutting depending on the clearance.
Patrick L. is offline   Reply With Quote
Old 08-12-2019, 10:34 AM   #10
Purdy Swoft
Senior Member
 
Purdy Swoft's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 8,099
Default Re: valve clearence

I use stainless steel valves with the original mushroom style stem . I use adjustable lifters and adjust for sixteen thousands clearance . This same clearance of sixteen thousands was recommended for both intake and exhaust valves by the grinder of my super street Winfield 3/4 race regrind cams . Less clearance gives a small fraction more lift . Extra clearance gives more time on the valve seat for more cooling of the valves and less chance of burning a valve . In the past , Snyders recommended sixteen thousands clearance .
Purdy Swoft is offline   Reply With Quote
Old 08-12-2019, 11:52 AM   #11
Jim Brierley
Senior Member
 
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,066
Default Re: valve clearence

Duration also changes slightly, less clearance gives more duration. Too little clearance can cause valves to burn. I recommend .012" on intakes, .014" exhausts on my B and C re-grinds, which were taken off stock original cams.
Jim Brierley is offline   Reply With Quote
Old 08-12-2019, 12:27 PM   #12
Bob Bidonde
Senior Member
 
Bob Bidonde's Avatar
 
Join Date: May 2010
Location: Long Island, NY
Posts: 3,429
Default Re: valve clearence

Stainless steel replacement valves for Model A & B engines are the same material for intake and exhaust valves.


The most common stainless steels for automotive exhaust valves are 21-2N and 21-4N. These are austenitic steels:

21-2N = 21% Chromium & 2% Nickle and so forth.


Valve clearance is a function of linear thermal expansion. Stainless steel does not conduct heat as well as carbon steel, so I would guess that the valve clearances for stainless valves would be equal to or perhaps less than Ford's original valves.



I run my engines with stainless valves at the Model B engine specs of 0.013" intakes and 0.015" exhausts. When the engine is cold, there is no valve clatter with these clearances.


Valve clatter (Noise) is a sign that the impact energy acting on the valve train is higher than it should be.
__________________
Bob Bidonde
Bob Bidonde is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:46 AM.