The Ford Barn

Talkwrench · 02-23-2020, 06:38 AM

Anyone seen a thrust bearing like this one, I've not seen one?

JM 35 Sedan · 02-23-2020, 08:47 AM

I've seen a couple varients of those cluster gear thrust washers, but not one quite like that. Of course even at my old age....there are many things I have yet to see

JM 35 Sedan · 02-23-2020, 08:52 AM

Maybe Third Gen, Charlie ny, or MacVP could tell you a thing or two about that type of thrust washer.
May be even something unique to Canadian/Australian manufacture.

Terry,OH · 02-23-2020, 10:14 AM

I think one of the other chaps, down under, was looking for that style of thrust washers.

Charlie ny · 02-23-2020, 10:24 AM

I believe John has it....Canadian style thrust washer. I'd be shocked if Mac VanPelt did not have some in his inventory.
Charlie ny

Talkwrench · 02-23-2020, 07:20 PM

Sponsored Links (Register now to hide all advertisements)

It may have been Lawrie..? I seem to remember he had something like it he was trying to find, might shoot him an email.. Any leads for another one would be helpful guys.
See if Mac sees the post .

Lawrie · 02-24-2020, 01:16 AM

Rob, what I did was to machine the end of the cluster gear to fit the 8m-7129 t/washer, a little machining on the lathe and then mill the tang to fit the 8M -7129 washer
lawrie
sorry about the upside down pic

Talkwrench · 02-24-2020, 05:00 AM

Thanks Lawrie, I've let Phil know he is probably capable of doing this.
Is that snap ring (?) that's in the end of the cluster normal for that type for thrust washer end.?

JM 35 Sedan · 02-24-2020, 02:19 PM

Hi Laurie, did that picture post upside down have anything to do with you being on the other side of the world? jk

35fordtn · 02-24-2020, 02:35 PM

I've run into that form of a strange thrust washer twice. BOTH times they belong to two different customers both from Australia. I had some (very few)NOS and may have one left. It carries the Canadian part# C91A-7129. There were two different varieaties of it (C91A-7129-E and C91A-7129-F)

35ragtop · 02-24-2020, 03:34 PM

Yes Rob, I have.
just rebuilt my 38 box using that setup. I didnt use a new part as it was within spec when assembled. Maybe one of us should buy that new one from Mike.
Dave h

JSeery · 02-24-2020, 05:05 PM

Here you go Lawrie.

Lawrie · 02-24-2020, 06:08 PM

Thanks,
Lawrie

Talkwrench · 02-24-2020, 06:40 PM

Ok Mike if you find another one let me know and I'll pass it on as its not my box Im just helping someone.

35fordtn · 02-24-2020, 08:24 PM

I checked tonight and although I thought I had one more left it appears as though I do not.. If I find another I will gladly let one of you AU guys have it. you guys have it tough enough with shipping and customs charges from the US

Talkwrench · 02-24-2020, 09:49 PM

Ok Thanks Mike . yes and at 65c to the USD.. its not easy..

phil pavicich · 03-15-2020, 07:54 AM

Still looking for this thrust washer any leads please thankyou in advance

02-23-2020, 08:47 AM	#2
JM 35 Sedan Senior Member Join Date: May 2010 Location: Near Rising Sun, Maryland Posts: 10,858	Re: 39 gearbox thrust bearing I've seen a couple varients of those cluster gear thrust washers, but not one quite like that. Of course even at my old age....there are many things I have yet to see __________________ *John* *"Never give up on what you really want to do. The person with big dreams is more powerful than one with all the facts". Albert Einstein*

02-23-2020, 08:52 AM	#3
JM 35 Sedan Senior Member Join Date: May 2010 Location: Near Rising Sun, Maryland Posts: 10,858	Re: 39 gearbox thrust bearing Maybe Third Gen, Charlie ny, or MacVP could tell you a thing or two about that type of thrust washer. May be even something unique to Canadian/Australian manufacture. __________________ *John* *"Never give up on what you really want to do. The person with big dreams is more powerful than one with all the facts". Albert Einstein*

02-23-2020, 10:14 AM	#4
Terry,OH Senior Member Join Date: May 2010 Posts: 4,743	Re: 39 gearbox thrust bearing I think one of the other chaps, down under, was looking for that style of thrust washers.

02-23-2020, 10:24 AM	#5
Charlie ny BANNED Join Date: May 2010 Posts: 3,019	Re: 39 gearbox thrust bearing I believe John has it....Canadian style thrust washer. I'd be shocked if Mac VanPelt did not have some in his inventory. Charlie ny

02-23-2020, 07:20 PM	#6
Talkwrench Senior Member Join Date: Aug 2012 Location: Perth, Western Australia Posts: 2,687	Re: 39 gearbox thrust bearing Sponsored Links (Register now to hide all advertisements) It may have been Lawrie..? I seem to remember he had something like it he was trying to find, might shoot him an email.. Any leads for another one would be helpful guys. See if Mac sees the post . __________________ *"Came too close to dying to stop living now!"*

02-24-2020, 05:00 AM	#8
Talkwrench Senior Member Join Date: Aug 2012 Location: Perth, Western Australia Posts: 2,687	Re: 39 gearbox thrust bearing Thanks Lawrie, I've let Phil know he is probably capable of doing this. Is that snap ring (?) that's in the end of the cluster normal for that type for thrust washer end.? __________________ *"Came too close to dying to stop living now!"*

02-24-2020, 02:19 PM	#9
JM 35 Sedan Senior Member Join Date: May 2010 Location: Near Rising Sun, Maryland Posts: 10,858	Re: 39 gearbox thrust bearing Hi Laurie, did that picture post upside down have anything to do with you being on the other side of the world? jk __________________ *John* *"Never give up on what you really want to do. The person with big dreams is more powerful than one with all the facts". Albert Einstein*

02-24-2020, 02:35 PM	#10
35fordtn Senior Member Join Date: Aug 2010 Location: McMinnville, TN Posts: 2,327	Re: 39 gearbox thrust bearing I've run into that form of a strange thrust washer twice. BOTH times they belong to two different customers both from Australia. I had some (very few)NOS and may have one left. It carries the Canadian part# C91A-7129. There were two different varieaties of it (C91A-7129-E and C91A-7129-F)

02-24-2020, 03:34 PM	#11
35ragtop Senior Member Join Date: Dec 2010 Location: Gold Coast , Australia Posts: 249	Re: 39 gearbox thrust bearing Yes Rob, I have. just rebuilt my 38 box using that setup. I didnt use a new part as it was within spec when assembled. Maybe one of us should buy that new one from Mike. Dave h

02-24-2020, 06:08 PM	#13
Lawrie Senior Member Join Date: May 2010 Location: Qld, Australia Posts: 4,210	Re: 39 gearbox thrust bearing Thanks, Lawrie

02-24-2020, 06:40 PM	#14
Talkwrench Senior Member Join Date: Aug 2012 Location: Perth, Western Australia Posts: 2,687	Re: 39 gearbox thrust bearing Ok Mike if you find another one let me know and I'll pass it on as its not my box Im just helping someone. __________________ *"Came too close to dying to stop living now!"*

02-24-2020, 08:24 PM	#15
35fordtn Senior Member Join Date: Aug 2010 Location: McMinnville, TN Posts: 2,327	Re: 39 gearbox thrust bearing I checked tonight and although I thought I had one more left it appears as though I do not.. If I find another I will gladly let one of you AU guys have it. you guys have it tough enough with shipping and customs charges from the US

02-24-2020, 09:49 PM	#16
Talkwrench Senior Member Join Date: Aug 2012 Location: Perth, Western Australia Posts: 2,687	Re: 39 gearbox thrust bearing Ok Thanks Mike . yes and at 65c to the USD.. its not easy.. __________________ *"Came too close to dying to stop living now!"*

03-15-2020, 07:54 AM	#17
phil pavicich Member Join Date: Aug 2010 Location: australia Posts: 58	Re: 39 gearbox thrust bearing Still looking for this thrust washer any leads please thankyou in advance

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode