Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 07-10-2013, 03:16 PM   #1
duffer
Senior Member
 
duffer's Avatar
 
Join Date: Aug 2012
Location: clinton township michigan
Posts: 273
Default oil plug question

What does everyone put on there oil plug to stop it from leaking? I tried the white teflon tape but it still leaks. Would a non hardening form a gasket sealant work or pipe dope?
duffer is offline   Reply With Quote
Old 07-10-2013, 03:35 PM   #2
Mitch//pa
BANNED
 
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
Default Re: oil plug question

you shouldn't need anything just the sealing washer under the head
Mitch//pa is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 07-10-2013, 03:41 PM   #3
duffer
Senior Member
 
duffer's Avatar
 
Join Date: Aug 2012
Location: clinton township michigan
Posts: 273
Default Re: oil plug question

What i ment to say was the transmission plug. Here is a picture with the white teflon tape, that doesn't seem to work.
Attached Images
File Type: jpg 101_3194.jpg (19.8 KB, 39 views)
duffer is offline   Reply With Quote
Old 07-10-2013, 03:42 PM   #4
heneste
Senior Member
 
heneste's Avatar
 
Join Date: Nov 2010
Location: Ottawa,Ontario, Canada
Posts: 271
Default Re: oil plug question

If you do need a tape sealant, they do sell a gas/oil resistant teflon tape that is less likely to dissolve in presence of petroleum.
It's a little stiffer than the regular white teflon tape.
I have used it on the oil plug at the side of the block when I had a small leak from the 1/8" plug and no problems so far.
heneste is offline   Reply With Quote
Old 07-10-2013, 03:48 PM   #5
J Franklin
Senior Member
 
J Franklin's Avatar
 
Join Date: May 2010
Location: Oregon
Posts: 5,962
Default Re: oil plug question

just install the plug tight with no extra anything! Please don't ask what torque setting to use.
J Franklin is offline   Reply With Quote
Old 07-10-2013, 04:10 PM   #6
Mitch//pa
BANNED
 
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
Default Re: oil plug question

Sponsored Links (Register now to hide all advertisements)
hahaaaah
i use liquid teflon
Mitch//pa is offline   Reply With Quote
Old 07-10-2013, 04:19 PM   #7
Farrell In Vancouver
Senior Member
 
Farrell In Vancouver's Avatar
 
Join Date: May 2010
Location: Pitt Meadows BC
Posts: 1,003
Default Re: oil plug question

You may have a crack that is opening up as you tighten in the plug. Take a close look for one before you reef that plug in too far. I thought I had a leak at the trans. drain plug but it turned out to be a drip from the cluster gear and reverse idler shafts. It just ran down the casting seam and gathered at the drain plug. I believe Snyders still sells a transmission seal kit to fix that problem.
Farrell In Vancouver is offline   Reply With Quote
Old 07-10-2013, 04:42 PM   #8
newshirt
Senior Member
 
newshirt's Avatar
 
Join Date: Jan 2011
Location: Colorado Springs
Posts: 868
Default Re: oil plug question

Another possibility: if you have leaks around the oil pan, oil can blow back onto that tranny plug and make it look like it leaks.
__________________
Ray White
newshirt is offline   Reply With Quote
Old 07-10-2013, 08:24 PM   #9
Vic in E-TN
Senior Member
 
Join Date: May 2010
Location: Maryville, TN
Posts: 491
Default Re: oil plug question

Teflon tape is impervious to oil, gasoline and gas (as in natural gas). There are two types of Teflon tape. The white is usually found in the stores. You may have to search for the yellow type. HD or Lowe's carries it. It is usually used for gas lines in the home and industry. It is thicker than the white variety. I have found that the liquid Teflon can be a pain to use in certain orientations,
Vic
Vic in E-TN is offline   Reply With Quote
Old 07-10-2013, 08:40 PM   #10
SeaSlugs
Senior Member
 
SeaSlugs's Avatar
 
Join Date: May 2010
Location: Central, IL
Posts: 3,968
Default Re: oil plug question

since its a tapered plug my guess is someone overtightened it and theres a hairline crack as mentioned above. IF you find there is drain the trans, clean the crack down to bare shiney metal, use acetone to remove all oil residue and fill/cover the crack with JB weld. ive had to do this on modern cars a few times. been holding 7 years on the oldest one and no leaks and bone dry paint it whatever color you want, may not look the best but you wont have a leak...

anyhow im just checking but you are wrapping the tape the right way arent you? if not it wont seal easily. ( i learned the hard way haha)
__________________
1929 Model AA - Need long splash aprons!
SeaSlugs is offline   Reply With Quote
Old 07-10-2013, 10:04 PM   #11
johnsor
Senior Member
 
Join Date: May 2010
Location: Spooner, Wisconsin
Posts: 242
Default Re: oil plug question

For years I have just used a good plumbers pipe dope on my transmission plugs, taking care to not over tighten, and never had a leak problem. Of course if you have a crack in the threads, that's a different issue.
johnsor is offline   Reply With Quote
Old 07-11-2013, 08:09 AM   #12
V4F
Senior Member
 
V4F's Avatar
 
Join Date: May 2010
Location: ca.
Posts: 2,522
Default Re: oil plug question

first I would get rid of the BIG plug for a plug that is flush . good rock breaker there .
__________________
V4f
V4F is offline   Reply With Quote
Old 07-11-2013, 08:31 AM   #13
Kurt in NJ
Senior Member
 
Kurt in NJ's Avatar
 
Join Date: May 2010
Location: on the Littlefield
Posts: 6,158
Default Re: oil plug question

If there are debris in the threads ---does it feel gritty when it is threaded in?? the debris will leave a leakage path and chew up any teflon tape

Previous tightenings with debris on the threads can damage the threads, a refreshing of the threads with a pipe tap along with a new plug can be needed

Mercedes still uses a tapered thread plug, I never use sealer or tape on them or my old fords

If the case is cracked around the boss nothing put on the threads will stop the leak
Kurt in NJ is online now   Reply With Quote
Old 07-11-2013, 05:52 PM   #14
1crosscut
Senior Member
 
1crosscut's Avatar
 
Join Date: Feb 2011
Location: Lincoln, Nebraska
Posts: 1,908
Default Re: oil plug question

1st thing that I would do is clean it up really good with some solvent and camp out under the car with a bright light and a cold beer and wait until I see the first little bead of oil show up to pin point the leak. If you don't see it by the time you finish your 1st beer take a break in the easy chair with another one and check it when that one is empty..... If it is a crack that is causing it to leak or just bad threads you could drain the transmission, reinstall the plug, clean it up good and put a quick smear of silicone gasket sealer around the plug. Should stop it until the next time you change your transmission oil.
__________________
Dave / Lincoln Nebraska
1crosscut is offline   Reply With Quote
Old 07-12-2013, 06:51 PM   #15
Junior
Member
 
Junior's Avatar
 
Join Date: Aug 2012
Location: Valdese, North Carolina
Posts: 85
Default Re: oil plug question

My oil plug had a plastic washer that leaked. Replaced it with a fiber washer that I picked up at Auto Zone last week when I changed the oil. No leaks yet.
__________________
Learning the A at the Ford Barn, so I can pass it down do the next generation.
Junior is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:30 PM.