Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 05-01-2019, 07:05 PM   #1
RandyMettler
Senior Member
 
Join Date: Dec 2018
Posts: 128
Default Thermostat orientation

Is this the correct orientation for a thermostat. I'm 98 percent sure it is, but than there is the 2 percent that worries me. The photo below shows the thermostat orientation.
Attached Images
File Type: jpg 100_7836.jpg (52.1 KB, 169 views)
RandyMettler is offline   Reply With Quote
Old 05-01-2019, 08:30 PM   #2
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Thermostat orientation

You have this installed properly.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 05-01-2019, 08:42 PM   #3
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: Thermostat orientation

Now you need to have a way to retain it so it doesn't turn inside the hose.
JSeery is offline   Reply With Quote
Old 05-01-2019, 09:00 PM   #4
RandyMettler
Senior Member
 
Join Date: Dec 2018
Posts: 128
Default Re: Thermostat orientation

Yah, I had one flip one me on my first test run. Driving on a short test drive, while constantly watching the temperature gauge, it went from 180 to 145 in a matter of seconds. I knew something was wrong. I drained the radiator an the thermostat was rotated. I have since put a third hose clamp just above the heads water outlets. I don't know of any other way of retaining the thermostat.

When this happens, the cooling capacity transfers to the side of the motor that the thermostat rotated, path of least resistance. In my opinion all flatheads should have temperature sending unit installed on both sides of the motor.

Last edited by RandyMettler; 05-01-2019 at 09:14 PM.
RandyMettler is offline   Reply With Quote
Old 05-01-2019, 10:18 PM   #5
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: Thermostat orientation

There are several methods to retain them and a number of threads on the topics. Examples are fine wires that fit between the head and the hose, or use a metal sleeve inside the hose.
JSeery is offline   Reply With Quote
Old 05-02-2019, 01:06 PM   #6
drolston
Senior Member
 
drolston's Avatar
 
Join Date: Jun 2014
Location: Williamsburg, VA
Posts: 1,622
Default Re: Thermostat orientation

Sponsored Links (Register now to hide all advertisements)
I use chrome pipes between the head and radiator. The tube inside the short hose connecting to the head keeps the thermostat in place.

I saw the temperature go to hot (the top mark on the gauge is about 200 degrees) first, and then drop to the thermostat temp. With the water flow blocked by the closed thermostat, the water at the sensor had to get to 200 before the water temperature up in the neck of the head gets hot enough to open the thermostat. I drilled two 5/32" holes hear the edge of each thermostat to let some flow past the bi-metal thermostat mechanism. Now the temp comes up to the thermostat temp without any overshoot.
drolston is offline   Reply With Quote
Old 05-06-2019, 12:08 PM   #7
philipswanson
Senior Member
 
Join Date: Oct 2015
Location: Bonita, CA
Posts: 1,374
Default Re: Thermostat orientation

I use a little JB Weld on the flange. Works like a champ and heat resistant and also keeps water from bypassing the thermostat.
philipswanson is offline   Reply With Quote
Old 05-07-2019, 01:49 AM   #8
Zeke5180
Member
 
Join Date: Feb 2019
Location: Illinois
Posts: 48
Default Re: Thermostat orientation

I'm getting ready to change the upper radiator hoses on my 37 and was told the shape of the hose will hold the thermostat in place. I'm I being misinformed?
Zeke5180 is offline   Reply With Quote
Old 05-07-2019, 08:45 AM   #9
Gary in La.
Senior Member
 
Gary in La.'s Avatar
 
Join Date: May 2010
Location: Louisiana
Posts: 866
Default Re: Thermostat orientation

Only original hoses had the rubber bulge I.D. that would hold the thermostat in place The re- production hoses do not have that and will not retain the thermostat. You must use an alternate method such as extra clamp or wire. I prefer the wire or soldered shim tabs on the thermostat rather than the clamps because they are too obvious from stock.
Gary in La. is offline   Reply With Quote
Old 05-07-2019, 08:54 AM   #10
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: Thermostat orientation

Quote:
Originally Posted by Zeke5180 View Post
I'm getting ready to change the upper radiator hoses on my 37 and was told the shape of the hose will hold the thermostat in place. I'm I being misinformed?
You are being misinformed. The original thermostats were barrel shaped and located near the radiator inlets. Modern thermostats need to be retained by some method.
JSeery is offline   Reply With Quote
Old 05-07-2019, 09:52 AM   #11
Gary in La.
Senior Member
 
Gary in La.'s Avatar
 
Join Date: May 2010
Location: Louisiana
Posts: 866
Default Re: Thermostat orientation

Years ago I had seen some old original '42-'48 style hoses that had a noticeable bulge inside the lower end to hold the thermostat. At one time Drake had a picture of the same thing in his catalog.
Gary in La. is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:25 AM.