Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 01-11-2018, 06:43 PM   #1
Frank Miller
Senior Member
 
Frank Miller's Avatar
 
Join Date: May 2010
Location: Auburn, MA
Posts: 1,370
Default Rear end stand

Anyone got any info or interest in this.
Attached Images
File Type: jpg rear end.jpg (35.1 KB, 322 views)
File Type: jpg temp.jpg (34.8 KB, 332 views)
__________________
“The technique of infamy is to start two lies at once and get people arguing heatedly over which is true.” ~ Ezra Pound
Frank Miller is offline   Reply With Quote
Old 01-11-2018, 07:52 PM   #2
old31
Senior Member
 
Join Date: Jan 2016
Posts: 690
Default Re: Rear end stand

Never mind interest, I wouldn't know how to use it.
old31 is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 01-12-2018, 02:02 AM   #3
Tom Wesenberg
Senior Member
 
Tom Wesenberg's Avatar
 
Join Date: May 2010
Location: Mpls, MN
Posts: 26,572
Default Re: Rear end stand

Interesting, and the first one I've seen. Hope someone can fill in the information.
Tom Wesenberg is offline   Reply With Quote
Old 01-12-2018, 02:32 AM   #4
hardtimes
Senior Member
 
hardtimes's Avatar
 
Join Date: May 2010
Location: South California
Posts: 5,695
Default Re: Rear end stand

Quote:
Originally Posted by Frank Miller View Post
Anyone got any info or interest in this.
That is a nice stand ! Is it Wilson ?
hardtimes is offline   Reply With Quote
Old 01-12-2018, 03:27 AM   #5
Frank Miller
Senior Member
 
Frank Miller's Avatar
 
Join Date: May 2010
Location: Auburn, MA
Posts: 1,370
Default Re: Rear end stand

Dixie
Attached Images
File Type: jpg Screenshot_2018-01-11-19-59-34.jpg (10.5 KB, 205 views)
__________________
“The technique of infamy is to start two lies at once and get people arguing heatedly over which is true.” ~ Ezra Pound
Frank Miller is offline   Reply With Quote
Old 01-12-2018, 06:18 AM   #6
Ed Saniewski
Senior Member
 
Ed Saniewski's Avatar
 
Join Date: May 2010
Location: Denville NJ
Posts: 936
Default Re: Rear end stand

Frank, can you give us the link, I can not read the ad you posted. If I try to inlarge it, it distorts. Thanks.
__________________
Model A Ford Club of New Jersey
http://www.mafcnj.org

Model A Pick Up Owners and Enthusiasts
https://www.fordbarn.com/forum/group.php?groupid=5
Ed Saniewski is offline   Reply With Quote
Old 01-12-2018, 07:19 AM   #7
Frank Miller
Senior Member
 
Frank Miller's Avatar
 
Join Date: May 2010
Location: Auburn, MA
Posts: 1,370
Default Re: Rear end stand

See if this works. I could read that on my phone but not on my PC.

https://books.google.com/books?id=u_...0stand&f=false
__________________
“The technique of infamy is to start two lies at once and get people arguing heatedly over which is true.” ~ Ezra Pound
Frank Miller is offline   Reply With Quote
Old 01-12-2018, 10:07 AM   #8
1930artdeco
Senior Member
 
1930artdeco's Avatar
 
Join Date: May 2010
Location: Oakland, CA
Posts: 2,294
Default Re: Rear end stand

If you were closer....

Mike
__________________
1930 TownSedan (Briggs)
Still learning after all these years....
1930artdeco is offline   Reply With Quote
Old 01-12-2018, 12:30 PM   #9
BRENT in 10-uh-C
Senior Member
 
BRENT in 10-uh-C's Avatar
 
Join Date: May 2010
Location: Eastern Tennessee
Posts: 7,949
Default Re: Rear end stand

What I am about to say should not influence anyone's decision whether to purchase this one or not, but I have seen restored ones fetch as much as $2,500.00, and the value decreases somewhat depending on condition. I have included a couple of ads on them below, and I have quite a few detailed pictures of them that I have collected over the years off the internet.

For me, there was a time when I really wanted one and just could not find one that I could either afford or obtain easily. I even drew up plans to fabricate one to my specs to use here in the shop, and the bottom line for me is I did not have enough room to store it when we would not be using it. For us, we probably rebuild an average of one rear end assembly per month, so we would not be using it enough to justify the extra time needed in setting it up to use or stowing it away. Based on the pictures Frank posted, it appears that owner encountered the same situation as I.

With all that said, these are extremely rare if all of the pieces are there, and for someone who wants to collect era service tools, or for a club purchase or museum display, I think this would be a great asset to own. Hopefully Frank's unit will be purchased by someone who has the ability to put it back in use again.

.
Attached Images
File Type: jpg $(KGrHqZ,!noE8YKMVU3PBPKgd8DTQw~~60_12.jpg (42.6 KB, 92 views)
File Type: jpg s-l1600.jpg (51.7 KB, 81 views)
__________________
.

BRENT in 10-uh-C
.
www.model-a-ford.com
...(...Finally Updated!! )

.
BRENT in 10-uh-C is offline   Reply With Quote
Old 01-12-2018, 03:36 PM   #10
Frank Miller
Senior Member
 
Frank Miller's Avatar
 
Join Date: May 2010
Location: Auburn, MA
Posts: 1,370
Default Re: Rear end stand

I am posting price and info in swap section.
__________________
“The technique of infamy is to start two lies at once and get people arguing heatedly over which is true.” ~ Ezra Pound
Frank Miller is offline   Reply With Quote
Old 01-13-2018, 03:48 PM   #11
BILL WILLIAMSON
Senior Member
 
BILL WILLIAMSON's Avatar
 
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 11,848
Default Re: Rear end stand

A Doctor "might" use it for rear end exams????
Bill Gross
__________________
"THE ASSISTANT GURU OF STUFF"
BILL WILLIAMSON is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:22 AM.