11-14-2021, 02:54 PM | #1 |
Senior Member
Join Date: May 2010
Location: Georgetown Divide Kelsey ca
Posts: 868
|
Roller
A Fedex shipment away from becoming a roller. Only took ten years but is on the front burner now future resting place for a 1929 standard coupe .
__________________
Dennis in Kelsey ca |
11-14-2021, 03:28 PM | #2 |
Member
Join Date: Feb 2014
Location: Sierra Foothills
Posts: 74
|
Re: Roller
Way to go Dennis!
|
Sponsored Links (Register now to hide all advertisements) |
|
11-14-2021, 04:32 PM | #3 |
Senior Member
Join Date: Feb 2017
Location: Zanesville Ohio USA
Posts: 268
|
Re: Roller
Man, I remember those days. You get it that far and then you want to keep going til it's completed!
__________________
1928 Niagara Blue Phaeton 1972 Olds 442 Convertible 1979 MGB -Life's Too Short To Drive Boring Cars- |
11-14-2021, 05:11 PM | #4 |
Senior Member
Join Date: Sep 2019
Location: Fort Gratiot, Michigan
Posts: 2,296
|
Re: Roller
Congratulations, keep up the great work!
|
11-14-2021, 05:19 PM | #5 |
Senior Member
Join Date: Feb 2011
Location: NNNNNNNNJJJJJJJJJJ
Posts: 6,785
|
Re: Roller
"keep them doggies rollin" rawhide!
|
11-14-2021, 06:20 PM | #6 |
Senior Member
Join Date: May 2010
Location: Lakeville, MN
Posts: 5,162
|
Re: Roller
Sponsored Links (Register now to hide all advertisements)
You sound like me - slow progress. Looken good. Rusty nelson |
11-15-2021, 12:02 AM | #7 |
Senior Member
Join Date: May 2010
Location: Georgetown Divide Kelsey ca
Posts: 868
|
Re: Roller
Waiting on parts for a 7 tooth steering box and column and some rear axle seals . I had a nice set of late 31 cast iron brake drums for the front they fit over the new brake lining with just a wiggle . And I uncovered a full set of tires and wheels the tires hold air but cracked and weathered good rollers . The wheels need paint but look great and roll straight no wobble couple bent spokes they might be the best set of wheels that I have . Tightened a lot of nuts and put in cotters today and drive in grease fittings . I have a set of steel drums for the rear they fit over the break lining also once I get the rears on I can adjust the brakes . But plenty of body work to keep me busy until parts arrive .
__________________
Dennis in Kelsey ca Last edited by Dennis Pereira; 11-15-2021 at 01:40 PM. |
11-15-2021, 07:50 AM | #8 |
Senior Member
Join Date: May 2010
Location: Long Island, NY
Posts: 3,463
|
Re: Roller
Keep the faith and your enthusiasm high! You are doing nice work.
__________________
Bob Bidonde |
11-23-2021, 04:51 PM | #9 |
Senior Member
Join Date: May 2010
Location: Georgetown Divide Kelsey ca
Posts: 868
|
Re: Roller
I have a roller I've accomplished more in the last two weeks then I have in years on this project. All my parts came in I'm adjusting brake rods and brakes I can spin three wheels easy the left rear is a two hander. Steering feels great but its off the ground lol I need to go back out and install cotters on all the brake rods befor I forget.
__________________
Dennis in Kelsey ca |
|
|
Sponsored Links (Register now to hide all advertisements) |
|