Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 04-28-2014, 03:17 PM   #1
Christoph
Senior Member
 
Christoph's Avatar
 
Join Date: Oct 2010
Location: Frankfurt am Main in Germany
Posts: 671
Default How to treat the new Front Leaf Spring

Got myself a new Front Leaf Spring and it says "Show Quality"
Its assembled and with center spring bolt and bronze shackle bushings.
So far, so good.

But - This is raw steel.

Now how should i treat it prior to mounting it into the car?
Demount the center spring bolt again and paint each leaf ???
Please advise

Thank you
Christoph
Christoph is offline   Reply With Quote
Old 04-28-2014, 03:35 PM   #2
CarlG
Senior Member
 
CarlG's Avatar
 
Join Date: Nov 2010
Location: Anchorage, Alaska
Posts: 9,109
Default Re: How to treat the new Front Leaf Spring

Un bolt everything. On the surfaces that will touch each other, spray with "Slip Plate". After it's dry, re-assemble and then paint the assembled spring with a good quality black chassis paint. I used Rustoleum Professional spray paint. Not sure what you would have available there.
Attached Images
File Type: jpg Slip Plate 330403.jpg (7.3 KB, 40 views)
__________________
Alaskan A's
Antique Auto Mushers of Alaska
Model A Ford Club of America
Model A Restorers Club
Antique Automobile Club of America
Mullins Owner's Club
CarlG is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 04-28-2014, 05:38 PM   #3
SeaSlugs
Senior Member
 
SeaSlugs's Avatar
 
Join Date: May 2010
Location: Central, IL
Posts: 3,968
Default Re: How to treat the new Front Leaf Spring

Not to be a stick in the mud but wouldn't it be better to paint each leaf before applying slip plate?

Sure where the leafs rub the paint may flake off but everywhere it doesnt rub would be coated with paint to prevent rust and then with the 2nd preventative of rust the slip plate would be there.

what killed alot of the leafs i see is water getting trapped between each leaf and causing pits. If its painted and greasy it should outlast you.
__________________
1929 Model AA - Need long splash aprons!
SeaSlugs is offline   Reply With Quote
Old 04-28-2014, 05:57 PM   #4
Mitch//pa
BANNED
 
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
Default Re: How to treat the new Front Leaf Spring

i powdercoated mine front and rear, lubed assembled
Attached Images
File Type: jpg image.jpg (77.9 KB, 94 views)
Mitch//pa is offline   Reply With Quote
Old 04-28-2014, 05:59 PM   #5
CarlG
Senior Member
 
CarlG's Avatar
 
Join Date: Nov 2010
Location: Anchorage, Alaska
Posts: 9,109
Default Re: How to treat the new Front Leaf Spring

Either way, just make sure to get the slip plate (or other lubricant) in between each leaf.
__________________
Alaskan A's
Antique Auto Mushers of Alaska
Model A Ford Club of America
Model A Restorers Club
Antique Automobile Club of America
Mullins Owner's Club
CarlG is offline   Reply With Quote
Old 04-28-2014, 06:28 PM   #6
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,374
Default Re: How to treat the new Front Leaf Spring

Sponsored Links (Register now to hide all advertisements)
"Not to be a stick in the mud but wouldn't it be better to paint each leaf before applying slip plate?"

That will increase the spring rate to a point where you think you have no springs.


"Un bolt everything. On the surfaces that will touch each other, spray with "Slip Plate". After it's dry, re-assemble and then paint the assembled spring with a good quality black chassis paint. I used Rustoleum Professional spray paint. Not sure what you would have available there."

About the only way to improve on that would be, have the leaves Parkerized before spraying with Slip Plate.

If you want the "stock look" just go with the paint.

If you want to keep water out, wrap the spring with black electrical tape from the eye to the U-bolt area.

If you want the real fancy look, get some of the old leather spring covers.
Pete is offline   Reply With Quote
Old 04-28-2014, 07:33 PM   #7
SeaSlugs
Senior Member
 
SeaSlugs's Avatar
 
Join Date: May 2010
Location: Central, IL
Posts: 3,968
Default Re: How to treat the new Front Leaf Spring

Quote:
Originally Posted by Pete View Post
"Not to be a stick in the mud but wouldn't it be better to paint each leaf before applying slip plate?"

That will increase the spring rate to a point where you think you have no springs.
Can you elaborate? Im not saying your wrong by any means i just don't understand how paint and grease increases the spring rate

By saying "think you have no springs" do you mean the car will sit lower or "bottom out" on hard bumps or be bouncy as can be?

I do know when i had to replace the shocks on my modern pickup with rear leafs i bounced the back-end with no shocks attached and i didn't think it would ever stop bouncing!
__________________
1929 Model AA - Need long splash aprons!
SeaSlugs is offline   Reply With Quote
Old 04-28-2014, 08:07 PM   #8
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,374
Default Re: How to treat the new Front Leaf Spring

Quote:
Originally Posted by SeaSlugs View Post
Can you elaborate? Im not saying your wrong by any means i just don't understand how paint and grease increases the spring rate

Grease and paint are a very poor lubricant. Grease alone is ok.
The paint would break down quickly from pressure and become GRIT.

Grease and oil are a poor spring lube because they attract dirt and grit.
It becomes like you lubed the spring with valve lapping compound.
That's why most people use Slip Plate or Dry Moly spray.

By saying "think you have no springs" do you mean the car will sit lower or "bottom out" on hard bumps or be bouncy as can be?

It would be extremely stiff with limited travel.

I do know when i had to replace the shocks on my modern pickup with rear leafs i bounced the back-end with no shocks attached and i didn't think it would ever stop bouncing!
...
Pete is offline   Reply With Quote
Old 04-28-2014, 08:11 PM   #9
SeaSlugs
Senior Member
 
SeaSlugs's Avatar
 
Join Date: May 2010
Location: Central, IL
Posts: 3,968
Default Re: How to treat the new Front Leaf Spring

Ahh i see. When i mentioned grease i meant slip plate...Not sure why i said grease lol.
__________________
1929 Model AA - Need long splash aprons!
SeaSlugs is offline   Reply With Quote
Old 04-29-2014, 12:14 AM   #10
Chuck Sea/Tac
Senior Member
 
Chuck Sea/Tac's Avatar
 
Join Date: May 2010
Location: Between Seattle & Tacoma
Posts: 2,351
Default Re: How to treat the new Front Leaf Spring

Quote:
Originally Posted by Mitch//pa View Post
i powdercoated mine front and rear, lubed assembled
So Mitch, how much did your spring pack thickness grow?
Chuck Sea/Tac is offline   Reply With Quote
Old 04-29-2014, 02:46 AM   #11
Tom Wesenberg
Senior Member
 
Tom Wesenberg's Avatar
 
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
Default Re: How to treat the new Front Leaf Spring

To prep a spring for use I first sandblast each leaf then grind any wear pockets smooth. I then grind a bevel on the bottom of each leaf to help prevent it wearing another pocket in the next leaf under it.

I then paint each leaf, coat the bottom of each leaf with Mystik JT-6 and sprinkle graphite on the grease. I then assemble the pack and wrap it with spring covers.

This is my friend's rear spring, which he had powdercoated.
Attached Images
File Type: jpg Spring Lube.jpg (126.1 KB, 76 views)
File Type: jpg Spring Lube2.jpg (65.0 KB, 67 views)
Tom Wesenberg is offline   Reply With Quote
Old 04-29-2014, 05:22 AM   #12
Mitch//pa
BANNED
 
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
Default Re: How to treat the new Front Leaf Spring

Quote:
Originally Posted by Chuck Sea/Tac View Post
So Mitch, how much did your spring pack thickness grow?
i did not mic how much thicker it was because it was a non issue, the front and rear pc'ed springs installed with no trouble.
Mitch//pa is offline   Reply With Quote
Old 04-29-2014, 06:38 AM   #13
dave in australia
Senior Member
 
Join Date: May 2010
Location: Victoria, Australia
Posts: 1,170
Default Re: How to treat the new Front Leaf Spring

When I did my springs, I sand blasted to remove corrosion. Skirfed the mating surfaces. Then chamfered the ends where they slide over the leaf below. Then applied a dry graphite lube, Lubribond 122, on all rubbing surfaces. Then assembled. Finally, remove excess lube from exposed surfaces with my favourite paint prep solvent and paint assembled.
dave in australia is offline   Reply With Quote
Old 04-30-2014, 02:05 PM   #14
Christoph
Senior Member
 
Christoph's Avatar
 
Join Date: Oct 2010
Location: Frankfurt am Main in Germany
Posts: 671
Default Re: How to treat the new Front Leaf Spring

Thank you for your suggestions !
FB is the place to be....

No Slip-Plate available over here.

Will use some othe special grease
http://www.mike-sander.de/
which (as well) protects against corrosion.
Will use some Graphite with that.
Than assamble again.
Than some paint (just outside).
Than more grease.

Than "Fettband" which is a warp-arround
http://mike.british-cars.de/Info_Fettband.htm
This keeps grease inside and it keeps water and
dirt outside ....

As this wont look original, i will use the original
spring-covers from the vendors to hide this.

Sounds like lots of work, but i do not want
do that again (within the next 85 years )


Thank you again

Best regards
Christoph



Christoph is offline   Reply With Quote
Old 04-30-2014, 11:45 PM   #15
SeaSlugs
Senior Member
 
SeaSlugs's Avatar
 
Join Date: May 2010
Location: Central, IL
Posts: 3,968
Default Re: How to treat the new Front Leaf Spring

Quote:
Originally Posted by Christoph View Post
Sounds like lots of work, but i do not want
do that again (within the next 85 years )



this is the question i keep asking myself as i go along restoring my truck: do i REALLY want to have to pull apart the worm drive rear end again? fight the rear leaf springs off? tear apart the transmission after its already been in the truck? etc

I used to be on a super tight budget - now its well i want it to look correct as possible sooo save my pennies and do it right the first time
__________________
1929 Model AA - Need long splash aprons!
SeaSlugs is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 04:45 PM.