Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 12-09-2018, 06:23 AM   #1
Dean Lemoine
Senior Member
 
Dean Lemoine's Avatar
 
Join Date: Nov 2018
Location: Dahlonega, Ga
Posts: 251
Default Rear spring lubrication

I've disassembled the rear springs on my '29 to be sandblasted and painted. I'm looking for recommendations on lubricants before being reassembled. Thanks in advance
Dean Lemoine is offline   Reply With Quote
Old 12-09-2018, 07:26 AM   #2
Step-down
Senior Member
 
Step-down's Avatar
 
Join Date: May 2012
Location: Hat City (Danbury CT)
Posts: 647
Default Re: Rear spring lubrication

You need to polish all the grove or marks in the surface also polish the ends of each leaf
So it doesn’t dig in the leaf below
__________________
"I can't cry as long as I know the Lord has risen "
Step-down is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 12-09-2018, 07:44 AM   #3
brokenspoke
Senior Member
 
Join Date: May 2010
Location: Anderson, Texas
Posts: 274
Default Re: Rear spring lubrication

NAPA sells "slip plate paint" in a spray can
brokenspoke is offline   Reply With Quote
Old 12-09-2018, 08:23 AM   #4
Terry, NJ
Senior Member
 
Terry, NJ's Avatar
 
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
Default Re: Rear spring lubrication

I don't know if it's bad or good, but heres how I did mine. With the spring out and under no tension, I merely loosened the center bolt so the gap between the leaves grew slightly. Then I poured oil across the side of the leaves and stood it on edge for about a week. Then turn it on the other side and do the same thing. The oil saturates the spring. Then I work grease in between the leaves. Tighten up the center bolt and I'm good to go. Rides good, no squeaks, what more do I want?
Terry
Terry, NJ is offline   Reply With Quote
Old 12-09-2018, 09:40 AM   #5
Ray64
Senior Member
 
Ray64's Avatar
 
Join Date: May 2010
Location: Grafton,OHIO
Posts: 727
Default Re: Rear spring lubrication

Powdered Graphite mixed with axle grease. Put on with paint brush.
Ray64 is offline   Reply With Quote
Old 12-09-2018, 10:26 AM   #6
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 4,992
Default Re: Rear spring lubrication

Sponsored Links (Register now to hide all advertisements)
Slip plate paint works great. Besides NAPA it's also available from your local friendly John Deere dealer.
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 12-09-2018, 10:40 AM   #7
Y-Blockhead
Senior Member
 
Y-Blockhead's Avatar
 
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,810
Default Re: Rear spring lubrication

You might consider installing spring covers after you get them all lubed up to keep the grease in and dirt out.
Y-Blockhead is offline   Reply With Quote
Old 12-09-2018, 11:40 AM   #8
JohnLaVoy
Senior Member
 
JohnLaVoy's Avatar
 
Join Date: Jun 2014
Location: Rocklin, CA
Posts: 779
Default Re: Rear spring lubrication

We use a product called EZ Slide, it is available at Tractor Supply locations and on line. The picture shows a 1QT can but it comes in spray cans too. We are doing the front spring for the next Model A Times build, a 1929 Cabriolet that will be a great tour car.
Attached Images
File Type: jpg ez slide low res.jpg (55.1 KB, 105 views)
JohnLaVoy is offline   Reply With Quote
Old 12-09-2018, 12:06 PM   #9
PC/SR
Senior Member
 
Join Date: May 2010
Location: Santa Rosa, CA
Posts: 1,275
Default Re: Rear spring lubrication

Powered graphite from the little tubes used for key locks.
PC/SR is offline   Reply With Quote
Old 12-09-2018, 03:02 PM   #10
whirnot
Senior Member
 
whirnot's Avatar
 
Join Date: Mar 2013
Location: Bend Or.
Posts: 1,051
Default Re: Rear spring lubrication

There are many opinions but I see no need to do anything. Never seen one worn out. Any lubricant such as oil that is exposed will attract dust, and turn it into grinding compound. If it ain't fixed Don't broke it.
__________________
Bill Worden

1929 Roadster
1929 Briggs Town Sedan
1930 Closed Cab pickup
Smith Motor Compressor
1951 Ford F1

High Desert Model A's
whirnot is offline   Reply With Quote
Old 12-09-2018, 04:16 PM   #11
Lawrie
Senior Member
 
Lawrie's Avatar
 
Join Date: May 2010
Location: Qld, Australia
Posts: 4,194
Default Re: Rear spring lubrication

grease and graphite powder then wrap the whole assembly with denso tape,
Lawrie
Lawrie is offline   Reply With Quote
Old 12-09-2018, 04:17 PM   #12
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,444
Default Re: Rear spring lubrication

After the leaves have been sandblasted like yours, I grind out the ridges and grooves till they won't cause a problem (not completely removed), then mix a handful of graphite in primer and paint them. Then, I reassemble and paint them black. The primer holds the graphite in place and being a dry lubricant, it does not attract dirt and grime. I've been doing that for about 25 years and it works so well, I can't see any reason to change.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Old 12-09-2018, 07:30 PM   #13
Jim M
Senior Member
 
Jim M's Avatar
 
Join Date: Nov 2010
Location: Sebastian, FL
Posts: 477
Default Re: Rear spring lubrication

I did my rear springs a short time ago. I also ground the bottom of the tapered ends of the leaves so they somewhat looked like a ski. This will prevent them from digging in the the leaf below after they are installed. I painted them black then sprayed them with the graphite sold in spray cans. Came out fantastic and no noise and hopefully will not dig into the leafs below.
Jim M is offline   Reply With Quote
Old 12-10-2018, 08:18 AM   #14
Terry, NJ
Senior Member
 
Terry, NJ's Avatar
 
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
Default Re: Rear spring lubrication

When oiling the leaves, it's important to remember that when tightly bolted and installed, under tension. there is no openings for dirt, sand to enter these joints. They are closed tight.
Terry
Terry, NJ is offline   Reply With Quote
Old 12-10-2018, 02:32 PM   #15
jwilliams81
Senior Member
 
jwilliams81's Avatar
 
Join Date: Sep 2016
Location: Cincinnati OH
Posts: 418
Default Re: Rear spring lubrication

Slip-Plate. Get the brush on kind. Two-Three coats per side.
When it's dried, put it all back together. Then give it the unit a coat of black paint.
__________________
1931 Murray Town Sedan. Black body with Apple Green pin stripe.
1923 Model T Touring with electric start. Low radiator
Cincinnati, Ohio
jwilliams81 is offline   Reply With Quote
Old 12-10-2018, 04:15 PM   #16
JOHN CT
Senior Member
 
JOHN CT's Avatar
 
Join Date: May 2010
Location: In my garage
Posts: 465
Default Re: Rear spring lubrication

I took the springs during the restoration stage. Ground the edges just to remove the groves paint with rust oleum paint. Then I rapped them with this cover. It’s been years and no squeaky
https://www.snydersantiqueauto.com/spring-covers
__________________
31 Tudor
66 Bonneville
57 Chevy pickup 27 T roadster pick up
JOHN CT is offline   Reply With Quote
Old 12-11-2018, 10:20 AM   #17
SeaSlugs
Senior Member
 
SeaSlugs's Avatar
 
Join Date: May 2010
Location: Central, IL
Posts: 3,968
Default Re: Rear spring lubrication

I sandblasted mine, ground out the grooves, painted with 2 coats of por 15, then slathered on my own 50/50 mix of graphite and open gear grease. Then bolted it all together and watched the grease spurt out like playdough. Springs are super smooth (as smooth as AA springs will allow at least)
__________________
1929 Model AA - Need long splash aprons!
SeaSlugs is offline   Reply With Quote
Old 04-11-2019, 02:38 PM   #18
Chris Haynes
Senior Member
 
Chris Haynes's Avatar
 
Join Date: May 2010
Location: Camarillo, CA and Pine Grove, CA
Posts: 2,830
Default Re: Rear spring lubrication

Quote:
Originally Posted by brokenspoke View Post
NAPA sells "slip plate paint" in a spray can
I find Slip Plate Lubricant. But nothing that says paint??
https://www.amazon.com/s?k=slip+plat...ref=nb_sb_noss
__________________
1921 Runabout
1930 Tudor
Early 1930 AA
Speed costs money. How fast do you want to go?
Chris Haynes is offline   Reply With Quote
Old 04-11-2019, 03:43 PM   #19
jwilliams81
Senior Member
 
jwilliams81's Avatar
 
Join Date: Sep 2016
Location: Cincinnati OH
Posts: 418
Default Re: Rear spring lubrication

Quote:
Originally Posted by Chris Haynes View Post
I find Slip Plate Lubricant. But nothing that says paint??
https://www.amazon.com/s?k=slip+plat...ref=nb_sb_noss
That's the correct link. Get the quart, brush it on.
__________________
1931 Murray Town Sedan. Black body with Apple Green pin stripe.
1923 Model T Touring with electric start. Low radiator
Cincinnati, Ohio
jwilliams81 is offline   Reply With Quote
Old 04-11-2019, 04:38 PM   #20
Tom Endy
Senior Member
 
Tom Endy's Avatar
 
Join Date: May 2010
Location: Southern California
Posts: 3,119
Default Re: Rear spring lubrication

I have restored a number of front and rear Model A springs. My method is to bead blast each leaf, grind the wear grooves down and bevel the sharp edges on the ends. I then sprayed the contact areas of each leaf with slip plate, which is a dry graphite, from John Deere with several heavy coats. It dries very quickly. As the leafs are assembled an excess will squeeze out. I wipe the spring clean with lacquer thinner and spray it with black Rustoleum paint. When installing back on the car I recommend installing the fabric spring covers available from the suppliers.


Tom Endy
Tom Endy is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:34 AM.