Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 06-16-2019, 09:53 PM   #1
Mabel1930
Junior Member
 
Join Date: Jun 2017
Posts: 22
Default Slight coolant seep on number 8 head nut (distributor cable)

I’ve noticed a slight weep after removing the nut in order to replace the distributor cable. Did a compression test and all cylinders show 30psi but I’m getting a tiny bit of white smoke. Before pulling the head, thought I’d try here for thoughts. Realized that when I put the nut back on without the distributor clip, I might not get full torque without a spacer (was having electrical issues so was testing the motor). Since the head gasket seal seems to have been broken, am I safe to just put my new distributor cable on when it arrives and torque that nut down properly with the clip or would folks advise pulling the head and replacing the gasket? Curious on people preferences for a prob like this.
Thanks!
Mark
Mabel1930 is offline   Reply With Quote
Old 06-16-2019, 09:59 PM   #2
Mulletwagon
Senior Member
 
Mulletwagon's Avatar
 
Join Date: Jan 2019
Location: Florida Panhandle
Posts: 585
Default Re: Slight coolant seep on number 8 head nut (distributor cable)

Seeping coolant around head studs is not uncommon. I used aluminized stop leak in the radiator and the problem went away. The engine only had about 1,000 miles on a rebuild. If that does not work no option except to pull the head. With 30 psi there may be a rebuild in the future.
Mulletwagon is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 06-16-2019, 10:05 PM   #3
Chuck Sea/Tac
Senior Member
 
Chuck Sea/Tac's Avatar
 
Join Date: May 2010
Location: Between Seattle & Tacoma
Posts: 2,351
Default Re: Slight coolant seep on number 8 head nut (distributor cable)

How did you check the compression? The proper way is with all spark plugs out, the throttle wide open, and three compression strokes on the cylinder your testing.
Chuck Sea/Tac is offline   Reply With Quote
Old 06-17-2019, 12:38 AM   #4
BILL WILLIAMSON
Senior Member
 
BILL WILLIAMSON's Avatar
 
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
Default Re: Slight coolant seep on number 8 head nut (distributor cable)

Without some practical expertise, does this car run???
Bill W.
__________________
"THE ASSISTANT GURU OF STUFF"
BILL WILLIAMSON is offline   Reply With Quote
Old 06-17-2019, 09:31 AM   #5
ryanheacox
Senior Member
 
ryanheacox's Avatar
 
Join Date: Apr 2013
Location: Northwest CT
Posts: 1,092
Default Re: Slight coolant seep on number 8 head nut (distributor cable)

30psi equates to a compression ratio of about 2:1... would an engine even run with a CR that low?


With all the head nuts torqued correctly, I would redo the compression test as described above in post #3.
ryanheacox is offline   Reply With Quote
Old 06-17-2019, 09:50 AM   #6
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,004
Default Re: Slight coolant seep on number 8 head nut (distributor cable)

Sponsored Links (Register now to hide all advertisements)
[QUOTE=Chuck Sea/Tac;1768376]How did you check the compression? The proper way is with all spark plugs out, the throttle wide open, and three compression strokes on the cylinder your testing.[/QUOTE

Also should be done on a warm/hot engine.
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 06-17-2019, 09:57 AM   #7
Railcarmover
BANNED
 
Join Date: Apr 2017
Location: Sacramento
Posts: 1,262
Default Re: Slight coolant seep on number 8 head nut (distributor cable)

A friends engine..with the oil pan off,but everything else assembled I could turn the engine over ,full revolutions,by hand..using the crankshaft throws,and it ran.
Railcarmover is offline   Reply With Quote
Old 06-17-2019, 10:02 AM   #8
midgetracer
Senior Member
 
midgetracer's Avatar
 
Join Date: May 2010
Location: Bismarck ND
Posts: 1,189
Default Re: Slight coolant seep on number 8 head nut (distributor cable)

Quote:
Originally Posted by Railcarmover View Post
A friends engine..with the oil pan off,but everything else assembled I could turn the engine over ,full revolutions,by hand..using the crankshaft throws,and it ran.
I pulled a B engine apart and the pistons actually fell out after the rods were disconnected. It must have ran prior to sitting. Not much compression needed to run.
midgetracer is offline   Reply With Quote
Old 06-17-2019, 03:16 PM   #9
BILL WILLIAMSON
Senior Member
 
BILL WILLIAMSON's Avatar
 
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
Default Re: Slight coolant seep on number 8 head nut (distributor cable)

When I do compression test, I give it 10 strokes, or when the pressure stops rising. Be sure the battery is fully charged & all guages all read differently!!
Bill W.
__________________
"THE ASSISTANT GURU OF STUFF"
BILL WILLIAMSON is offline   Reply With Quote
Old 06-18-2019, 08:32 PM   #10
Dodge
Senior Member
 
Join Date: Nov 2011
Location: Sonoma, CA.
Posts: 1,491
Default Re: Slight coolant seep on number 8 head nut (distributor cable)

Borrow another gauge or try in in another motor before you pull your motor apart....
Dodge is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:01 AM.