Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 09-29-2021, 12:53 PM   #1
Clem Clement
Senior Member
 
Clem Clement's Avatar
 
Join Date: May 2010
Location: Fairfax, VA
Posts: 3,390
Default Gas gauge quit

My '40MERC's gas gauge quit recently. Reads nil. Reaching under the dash, I feel no loose wires. No problems in the last 4 years. I don't know if the sender is modern. Tank about 3/4full. Next step pickup the trunk mat and inspect the gauge top?
TIA
Clem Clement is offline   Reply With Quote
Old 09-29-2021, 02:14 PM   #2
hotrodart
Senior Member
 
hotrodart's Avatar
 
Join Date: May 2010
Location: Shenandoah Valley Virginia
Posts: 220
Default Re: Gas gauge quit

CLEM - Most common failure seems to be the sending unit. I think your easiest first step is to pull out the sender (under the trunk mat) and determine if the float has failed......full of gas from a pin-hole, etc. If the float has gas in it, try moving the float/arm up and down, with the sender grounded with an alligator clip wire....to see if the dash gauge moves.


If no good results, then the sender or the gauge/wiring may be bad. Try a known good sender (borrowed fro Cliff Green or another club member), then you will know where to look next.......wiring or dash gauge.....neither of which is much fun.
hotrodart is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 09-29-2021, 06:01 PM   #3
51woodie
Senior Member
 
51woodie's Avatar
 
Join Date: Apr 2018
Location: Chelmsford, ON Canada
Posts: 524
Default Re: Gas gauge quit

Clem. I'm not familiar with a '40, but if it is the same fuel gauge system as my '46 coupe, I might be able to add some info. My fuel gauge was not reading full when the tank was full. One thing that I did while testing the gauge system, (you need the ignition on) was to disconnect the power to the coil to prevent damage to the point and/or coil. Another note, when the sender (in my case) is out of the tank, there will be some gas fumes in the area of the tank opening. If the disconnected fuel sender wire touches the tank with the ignition on, it will make a spark. I tested the circuit from the sender to the gauge by using a 2' lead with clips, so I could make the connection away from the tank opening. the gauge will read FULL when the gauge wire is connected to a ground. If you get a reading, the circuit is good, and the sender or float is likely at fault. In my case the float (aftermarket I think) was partially flooded.
51woodie is offline   Reply With Quote
Old 09-30-2021, 11:39 AM   #4
Clem Clement
Senior Member
 
Clem Clement's Avatar
 
Join Date: May 2010
Location: Fairfax, VA
Posts: 3,390
Default Re: Gas gauge quit

Thanks for the important safety tip
Clem
Clem Clement is offline   Reply With Quote
Old 09-30-2021, 12:40 PM   #5
v8nut
Senior Member
 
v8nut's Avatar
 
Join Date: Dec 2010
Location: San Jose, CA
Posts: 202
Default Re: Gas gauge quit

My original '39 sender has a cork float that is completely saturated with gas and stays sunk on the bottom of the tank. Jim in San Jose
v8nut is offline   Reply With Quote
Old 10-12-2021, 01:03 PM   #6
Clem Clement
Senior Member
 
Clem Clement's Avatar
 
Join Date: May 2010
Location: Fairfax, VA
Posts: 3,390
Default Re: Gas gauge quit

Sponsored Links (Register now to hide all advertisements)
The builder put in a new tank. I'm very slow lately and will get to it when I can. Life is in the way.
Thanks
Clem Clement is offline   Reply With Quote
Old 10-12-2021, 09:19 PM   #7
Zeke3
Senior Member
 
Zeke3's Avatar
 
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,401
Default Re: Gas gauge quit

Quote:
Originally Posted by v8nut View Post
My original '39 sender has a cork float that is completely saturated with gas and stays sunk on the bottom of the tank. Jim in San Jose
There is an old discussion on here that describes replacing the cork float with two replacement modern composite Model A floats glued together. I haven't tried it yet, but I have the same condition on my 1937 fuel sending unit as yours.
Zeke3 is online now   Reply With Quote
Old 12-04-2021, 10:42 PM   #8
Clem Clement
Senior Member
 
Clem Clement's Avatar
 
Join Date: May 2010
Location: Fairfax, VA
Posts: 3,390
Default Re: Gas gauge quit

Mine system is supposedly all rebuilt.
Clem Clement is offline   Reply With Quote
Old 12-04-2021, 10:58 PM   #9
petehoovie
Senior Member
 
petehoovie's Avatar
 
Join Date: May 2015
Posts: 7,924
Default Re: Gas gauge quit

Quote:
Originally Posted by Zeke3 View Post
There is an old discussion on here that describes replacing the cork float with two replacement modern composite Model A floats glued together. I haven't tried it yet, but I have the same condition on my 1937 fuel sending unit as yours.
See this link for the fix > https://fordbarn.com/forum/showthrea...ght=cork+float


Photo shows the removed original cork float and the newly installed replacement float.

Buy replacement float here > https://www.snydersantiqueauto.com/p...9370&cat=41706
__________________
The only thing nice about being imperfect is the joy it brings to others....

"Silver rings, your butt! Them's washers!"
"We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969

https://www.youtube.com/watch?v=7NReUd2_0u0

Last edited by petehoovie; 12-04-2021 at 11:04 PM.
petehoovie is offline   Reply With Quote
Old 12-04-2021, 11:23 PM   #10
VeryTangled
Senior Member
 
VeryTangled's Avatar
 
Join Date: May 2010
Location: (Not far enough...) Outside of DC
Posts: 3,386
Default Re: Gas gauge quit

Quote:
Originally Posted by v8nut View Post
My original '39 sender has a cork float that is completely saturated with gas and stays sunk on the bottom of the tank. Jim in San Jose
My solution at the time; The one piece that was useful on the repro sender was the float. I grafted it onto the original arm.
__________________
-Jeff H

Have you thought about supporting the Early Ford V-8 Foundation Museum?
VeryTangled is offline   Reply With Quote
Old 12-05-2021, 11:59 AM   #11
TJ
Senior Member
 
TJ's Avatar
 
Join Date: May 2010
Location: Napa,California
Posts: 6,005
Default Re: Gas gauge quit

Clem, supposed to be rebuilt and knowing it was rebuilt for sure are two different things. It sounds like a float issue, so pull the sender and check the float.
TJ is offline   Reply With Quote
Old 12-05-2021, 12:11 PM   #12
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Gas gauge quit

Clem, Remove the sending unit from the tank and cover the opening with a rag to prevent fumes. Then, lay the sending unit on a piece of cardboard away from the tank opening and use an alligator clipped wire to connect the wire from the gauge to the top of the sending unit. Then run another alligator clipped wire from the body of the sending unit to ground (for instance, the trunk floor latch). Then, switch on the ignition and move the float arm thru its range of motion to see if it registers properly with the gauge. If your float is brass, check it for hairline cracks which allow gas to seep in and give false readings. Switch OFF the ignition before you reinstall the sending unit. A Fordbarn SEARCH for Gas Tank Sending unit will yield much more info. The 1940 Ford gas tank sending unit is shown below. 40 Merc is probably the same and both are made by King-Sealy. Neither operates on the OHMs Principle.
https://www.fordbarn.com/forum/searc...rchid=25890535
Attached Images
File Type: jpg IMG_9093b.jpg (119.6 KB, 19 views)
File Type: jpg IMG_9097B.jpg (52.6 KB, 16 views)
File Type: jpg IMG_9104B.jpg (68.8 KB, 22 views)
File Type: jpg IMG_9106B.jpg (94.7 KB, 22 views)
File Type: jpg IMG_9109B.jpg (66.5 KB, 16 views)
File Type: jpg IMG_9101B.jpg (64.4 KB, 16 views)

Last edited by 19Fordy; 12-05-2021 at 01:03 PM.
19Fordy is offline   Reply With Quote
Old 02-10-2022, 02:49 AM   #13
Clem Clement
Senior Member
 
Clem Clement's Avatar
 
Join Date: May 2010
Location: Fairfax, VA
Posts: 3,390
Default Re: Gas gauge quit

Thanks
Clem Clement is offline   Reply With Quote
Old 02-13-2022, 03:34 PM   #14
Lawson Cox
Senior Member
 
Lawson Cox's Avatar
 
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
Default Re: Gas gauge quit

Quote:
Originally Posted by v8nut View Post
My original '39 sender has a cork float that is completely saturated with gas and stays sunk on the bottom of the tank. Jim in San Jose
Replace the float with a brass one. They are readily available.

Lawson
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes.

It is better to be seen, than viewed.

"We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm".
Lawson Cox is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:47 AM.