Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 10-15-2019, 12:11 PM   #1
DannL
Senior Member
 
DannL's Avatar
 
Join Date: Jul 2019
Location: Oklahoma City, OK
Posts: 184
Default Rewiring . . . What would you do different?

After troubleshooting a recent short in the headlight circuit, and finding other wires dangling or connected by a single strand . . . I decided I'd rewire the whole beast. That said . . for those who have taken this train already. . . what would you do differently if you had to do it again?

This is not a huge task by any means , but rework can be annoying sometimes. Will use modern 12 gauge wire (black) and install an 8 fuse block for the major circuits.
DannL is offline   Reply With Quote
Old 10-15-2019, 12:36 PM   #2
burner31
Senior Member
 
burner31's Avatar
 
Join Date: Dec 2014
Location: Shawnee, Ok
Posts: 3,471
Default Re: Rewiring . . . What would you do different?

Solder...solder everything, steer clear of crimping connections.
__________________
Keith
Shawnee OK
'31 SW 160-B
burner31 is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 10-15-2019, 11:47 PM   #3
DannL
Senior Member
 
DannL's Avatar
 
Join Date: Jul 2019
Location: Oklahoma City, OK
Posts: 184
Default Re: Rewiring . . . What would you do different?

Quote:
Originally Posted by burner31 View Post
Solder...solder everything, steer clear of crimping connections.

A pic of what spurred my interest in replacing the wires. Especially the headlight wiring. Years of being soaked with coolant and oils from the engine. The core wire strands inside are covered in an almost black patina. Once all of this is removed I'll cut into the harness at sections to see how far the oxidation goes. The connections here were all soldered (albeit poorly) at some point. They took your advice . . . even back then. ;-)
Attached Images
File Type: jpg 20191014_191133.jpg (44.3 KB, 167 views)
File Type: jpg 20191014_191122.jpg (59.5 KB, 152 views)
DannL is offline   Reply With Quote
Old 10-15-2019, 01:00 PM   #4
Tom Endy
Senior Member
 
Tom Endy's Avatar
 
Join Date: May 2010
Location: Southern California
Posts: 3,122
Default Re: Rewiring . . . What would you do different?

I would remove the wire from the light bail to the stoplight switch. And run a new wire direct from either the fuse or the terminal on the firewall to the switch. There is no reason for power to the stop lights to run through the bail.

This way if ever out on the road and a short circuit develops in the bail you can remove the wire from the generator to the bail and continue on in daylight and still have stop lights.

Tom Endy
Tom Endy is offline   Reply With Quote
Old 10-15-2019, 01:27 PM   #5
Floats
Senior Member
 
Floats's Avatar
 
Join Date: Dec 2013
Location: Mossel Bay, about 300km from Cape Town
Posts: 530
Default Re: Rewiring . . . What would you do different?

Hi Gents,
Yep, soldering joints and the brake lite wiring are good ideas. I would add a cutoff switch and
also consider turn signal wiring, even if not in use yet, it might become compulsory some time in the future.
I am considering turn signals on both my vintage cars.
__________________
Regards
Chris
Cape Town
28 Model A RPU, 29 Chevy Phaeton, 67 E Type FHC, 67 250SL Pagoda, 83 911 SC
Floats is offline   Reply With Quote
Old 10-16-2019, 10:49 PM   #6
DannL
Senior Member
 
DannL's Avatar
 
Join Date: Jul 2019
Location: Oklahoma City, OK
Posts: 184
Default Re: Rewiring . . . What would you do different?

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Tom Endy View Post
I would remove the wire from the light bail to the stoplight switch. And run a new wire direct from either the fuse or the terminal on the firewall to the switch. There is no reason for power to the stop lights to run through the bail.

This way if ever out on the road and a short circuit develops in the bail you can remove the wire from the generator to the bail and continue on in daylight and still have stop lights.

Tom Endy

Good observation. Granted, they could have just as easily connected at the relay, or the junction/terminal box. Of course that would cost a few extra feet of wire. Multiplied by 4,858,644 (more or else), that comes to 1840 miles of wire.
DannL is offline   Reply With Quote
Old 10-17-2019, 11:12 PM   #7
Penthode
Member
 
Penthode's Avatar
 
Join Date: Oct 2016
Posts: 60
Default Re: Rewiring . . . What would you do different?

I would not suggest using any wire less than 14 gauge on a 6 volt system. I rewired my car and used 10 gauge up to the fuse block, 12 gauge for headlights and wiper motor and 14 gauge elsewhere. Remember with a 50 watt headlamp, the current at 6 volts is more than 8 amps. 10 feet of 12 gauge is about 0.02 ohms, so the voltage drop in the wire alone is nearly 0.2 volts. 16 gauge is about 3 times the resistance per foot which means 0.6 volts is lost. Don't forget there are losses in the switch and the connectors. Nearing 1volt loss is quite a chunk out of the 6 volts total.

If you want to flash indicate the stop lights, you must run the brake lights to the direction indicator switch or else the relay.

I color coded the cables but only used modern wire matching as closely as possible the original Ford plan.

I also added a bakelite 4 fuse box replacement normally used for a Volkswagen Beetle because it looked "period". I mounted it on the firewall next to the central junction box for power distribution after the ammeter to four individual fuses for lights, direction signal, horn and wiper motor.

Wiring is fully loomed: no loose strands anywhere.

Last edited by Penthode; 10-17-2019 at 11:26 PM.
Penthode is offline   Reply With Quote
Old 11-26-2019, 11:27 AM   #8
klrh20frank
Member
 
Join Date: May 2010
Location: Garden Plain KS
Posts: 44
Default Re: Rewiring . . . What would you do different?

Thanks for the information. thanks again for helping me rebuild my rearend in vancouver.
klrh20frank is offline   Reply With Quote
Old 10-15-2019, 02:38 PM   #9
31Tudor
Senior Member
 
31Tudor's Avatar
 
Join Date: May 2010
Location: North Carolina
Posts: 611
Default Re: Rewiring . . . What would you do different?

I think I would just buy a wiring harness from one of the suppliers and be done with it. I have never had a problem with a stock wiring harness. They are correct the right color and go to the right places.
31Tudor is offline   Reply With Quote
Old 10-15-2019, 11:16 PM   #10
160B
Senior Member
 
160B's Avatar
 
Join Date: Aug 2010
Location: Port Orchard, WA
Posts: 1,498
Default Re: Rewiring . . . What would you do different?

Quote:
Originally Posted by 31Tudor View Post
I think I would just buy a wiring harness from one of the suppliers and be done with it. I have never had a problem with a stock wiring harness. They are correct the right color and go to the right places.
Only way to go!!! If you have problems on road trips you can get help from those traveling with you because it matches the wiring diagrams!!!
__________________
1931 160B & 1931 68B

If you don't have time to do it right the 1st time, how do you have time to do it the 2nd time?
160B is offline   Reply With Quote
Old 10-15-2019, 02:55 PM   #11
Y-Blockhead
Senior Member
 
Y-Blockhead's Avatar
 
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,817
Default Re: Rewiring . . . What would you do different?

Quote:
Originally Posted by DannL View Post
This is not a huge task by any means , but rework can be annoying sometimes. Will use modern 12 gauge wire (black) and install an 8 fuse block for the major circuits.
For sure one thing I would never do is use one wire color as you suggest to wire a car.

I am with 31 Tudor and just get the proper wiring harness. I have never used one of theirs but have heard Sacramento Vintage makes their own wiring harnesses and are highly thought of.
Y-Blockhead is offline   Reply With Quote
Old 10-15-2019, 10:54 PM   #12
DannL
Senior Member
 
DannL's Avatar
 
Join Date: Jul 2019
Location: Oklahoma City, OK
Posts: 184
Default Re: Rewiring . . . What would you do different?

In my case I've chosen black so that the new wiring will closely match the color of the old wiring . . . today. I've not yet found a modern harness replacement that follows the original color coding.

Last edited by DannL; 10-15-2019 at 11:09 PM.
DannL is offline   Reply With Quote
Old 11-25-2019, 04:19 PM   #13
Ted Duke
Senior Member
 
Join Date: Mar 2012
Location: Fairfield, Virginia
Posts: 615
Default Re: Rewiring . . . What would you do different?

Your original wiring was black?
Ted Duke is offline   Reply With Quote
Old 11-25-2019, 04:40 PM   #14
DannL
Senior Member
 
DannL's Avatar
 
Join Date: Jul 2019
Location: Oklahoma City, OK
Posts: 184
Default Re: Rewiring . . . What would you do different?

Quote:
Originally Posted by Ted Duke View Post
Your original wiring was black?
Mine was the original cloth covered harness. In the end I used modern red, green, white and black wire. I considered fusing individual circuits but the excess wiring held little benefit. Ended up with three main fuses only. Put all wires in black loom. It's amazing how basic the wiring is once all the nasty wiring was removed. Took the most part of a morning and afternoon to complete. There's about six inches of original wire running to the each of the cowl lights. It was in fine condition.

Last edited by DannL; 11-25-2019 at 10:31 PM.
DannL is offline   Reply With Quote
Old 11-25-2019, 05:04 PM   #15
dmaxweb
Senior Member
 
dmaxweb's Avatar
 
Join Date: May 2010
Location: Williamsburg, VA
Posts: 510
Default Re: Rewiring . . . What would you do different?

Quote:
Originally Posted by DannL View Post
In my case I've chosen black so that the new wiring will closely match the color of the old wiring . . . today. I've not yet found a modern harness replacement that follows the original color coding.

Perfect reproduction wiring harnesses:

Tyree Harris
Bumpass, Virginia
[email protected]
dmaxweb is offline   Reply With Quote
Old 10-16-2019, 01:14 AM   #16
dave in australia
Senior Member
 
Join Date: May 2010
Location: Victoria, Australia
Posts: 1,170
Default Re: Rewiring . . . What would you do different?

I do my own wiring harnesses. As I don't enter judging, I don't need the correct cloth covered wiring. I buy auto wiring, I add fuses, and because mine is a RHD, I use relays to reduce the current going through the light switch. The switch sits directly under the carb, so I want to reduce the chance of a fire if the carb has a small leak. I have a panel that is mounted on the LHS of the firewall, using the tank to firewall bolts. This way, there are no extra bolt holes, and it can be easily returned to stock by unbolting the panel. I also have LED indicators and a kill switch that sits just behind the gearstick at floor level. If something goes wrong, just reach down and kill the electricals.
dave in australia is offline   Reply With Quote
Old 10-16-2019, 05:22 AM   #17
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Rewiring . . . What would you do different?

I agree with the soldering/shrink tube, cutout, and stop light idea. And I like wiring things myself too. I would just stuff the wires in an 'old timey' woven loom. I also prefer to wire the ignition primary circuit more to modern/newer type of wire positions. I'd rather have the coil 'after' the switch.

Last edited by Patrick L.; 10-16-2019 at 08:44 AM.
Patrick L. is offline   Reply With Quote
Old 10-16-2019, 07:26 AM   #18
History
Senior Member
 
History's Avatar
 
Join Date: Oct 2017
Location: NC Mountains
Posts: 689
Default Re: Rewiring . . . What would you do different?

The wiring on mine was in very poor shape, many times spliced together and paper (freezer)? tape used to wrap it. The tail/brake light wire was ran the wrong way (around, over) things and was not long enough. There were three sets of plugs and wire about a foot long added to the end of it as extensions with paper tape.


I do have a question,,,,,, my head light sockets I guess have been replaced and the wire,, not the plug would fit in and a screw tightened to hold it. The plugs on the new harness will not fit in these sockets. What would you fellows do,,,,, cut the plugs off and strip the wire and insert or do they make socket transitions that would do both????

Not doing a show car so that doesn't matter but I hate to destroy the end of it in case the next owner would like to restore.
History is offline   Reply With Quote
Old 10-16-2019, 07:37 AM   #19
DannL
Senior Member
 
DannL's Avatar
 
Join Date: Jul 2019
Location: Oklahoma City, OK
Posts: 184
Default Re: Rewiring . . . What would you do different?

Quote:
Originally Posted by History View Post
The wiring on mine was in very poor shape, many times spliced together and paper (freezer)? tape used to wrap it. The tail/brake light wire was ran the wrong way (around, over) things and was not long enough. There were three sets of plugs and wire about a foot long added to the end of it as extensions with paper tape.


I do have a question,,,,,, my head light sockets I guess have been replaced and the wire,, not the plug would fit in and a screw tightened to hold it. The plugs on the new harness will not fit in these sockets. What would you fellows do,,,,, cut the plugs off and strip the wire and insert or do they make socket transitions that would do both????

Not doing a show car so that doesn't matter but I hate to destroy the end of it in case the next owner would like to restore.
Can you post a pic of the socket and plug?
DannL is offline   Reply With Quote
Old 10-16-2019, 07:52 AM   #20
History
Senior Member
 
History's Avatar
 
Join Date: Oct 2017
Location: NC Mountains
Posts: 689
Default Re: Rewiring . . . What would you do different?

Quote:
Originally Posted by DannL View Post
Can you post a pic of the socket and plug?
The plug on the light wire is just the standard plug that was original on the model A. Plug may not be the correct name but it's the same for the horn and tail lights. The sockets for my headlights is probably more modern. With it you would strip the wire and with the wire exposed, stick it on the socket hole and tighten a small screw on the side. Similar/exactly to wiring a trailer connector.
History is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:09 PM.