06-25-2022, 07:00 AM | #1 |
Member
Join Date: Nov 2012
Posts: 57
|
motor stand
Anyone know of a good motor stand for v8 flathead,the one mine is sitting on sits on the oil pan,and i want to take the pan off.any suggestions.
|
06-25-2022, 09:41 AM | #2 |
Senior Member
Join Date: Aug 2018
Location: Ottawa, ON
Posts: 854
|
Re: motor stand
I just bought a cheap heavy duty engine stand and fabbed up a plate the bolts to the exhaust holes. I then welded it to a tube that fit inside the tube in the stand. Works great unless you have the exh manifolds attached. There are folks who sell that exh plate.
|
Sponsored Links (Register now to hide all advertisements) |
|
06-25-2022, 10:54 AM | #3 |
Senior Member
Join Date: Sep 2013
Location: SoCal-Redlands
Posts: 3,018
|
Re: motor stand
Stumpy's Fabworks
stumpysfabworks.com FFESA - S85 $80.00
Ford Flathead 85-100HP 59AB/8BA Engine Stand Adapter *Fits standard eng. stand with 2-3/8"opening. Other sizes available, email me with your size needs if different. Not responsible if not checked.* Comes with mounting hardware ..............$80.00
__________________
Making the simple complicated for over 30 years. |
06-25-2022, 11:09 AM | #4 |
Senior Member
Join Date: Sep 2021
Location: summerton, sc
Posts: 353
|
Re: motor stand
cut the pipe to 45 deg and weld it up, make sure you have the plate right side up, just tack it to make sure.
|
06-25-2022, 01:44 PM | #5 |
Senior Member
Join Date: Jul 2010
Location: 36 miles north of Albany NY
Posts: 2,950
|
Re: motor stand
+1 on a stand from Stumpys.
|
06-25-2022, 01:55 PM | #6 |
Member
Join Date: Nov 2012
Posts: 57
|
Re: motor stand
Sponsored Links (Register now to hide all advertisements)
|
06-25-2022, 03:59 PM | #7 |
Senior Member
Join Date: May 2010
Location: NJ
Posts: 6,179
|
Re: motor stand
Are you talking about one for an engine stand or one that rolls around on the ground?
|
06-25-2022, 04:14 PM | #8 |
Senior Member
Join Date: May 2010
Posts: 2,484
|
Re: motor stand
Saw a nice run stand at local swap meet . It was the front frame of a 1 1/2 ton truck. Radiator and the works, Newc
|
06-25-2022, 11:42 PM | #9 |
Senior Member
Join Date: May 2012
Location: Queensland, Australia
Posts: 10,366
|
Re: motor stand
This is my Flathead Engine Stand and I find it very useful. Notice in the first picture with the Engine in the Stand, there is a Pin that you can lock the Engine in 4 different locations, so you can turn it upside down to work on the Bottom End, or you can lock it in so that you can easily mount the Flywheel and Clutch Plate. The Motor is very well attached on both side that really give it good support with no chance of damaging the Block. |
06-26-2022, 04:50 AM | #10 |
Senior Member
Join Date: Sep 2016
Location: sydney australia
Posts: 1,033
|
Re: motor stand
cradle stands are the go but lots of luck finding one and then getting them to part with it is another mountain you need to climb as a lot of them where converted into truck diff rebuild stands and are the bees knees for that job
|
06-26-2022, 01:07 PM | #11 |
Member
Join Date: Nov 2012
Posts: 57
|
Re: motor stand
thank you for all the coments,i orded one that bolts to exhust bolts. Mercman"s stand is ideal, but where would you find one
|
06-26-2022, 05:14 PM | #12 |
Senior Member
Join Date: Mar 2018
Location: Florida panhandle
Posts: 194
|
Re: motor stand
Like this
|
06-26-2022, 10:50 PM | #13 |
Senior Member
Join Date: May 2012
Location: Queensland, Australia
Posts: 10,366
|
Re: motor stand
Alternative Flathead V8 Engine Stand |
|
|
Sponsored Links (Register now to hide all advertisements) |
|