Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 10-28-2019, 03:21 PM   #1
Ruth
Senior Member
 
Join Date: May 2016
Location: Glide, Oregon
Posts: 1,334
Default Sagging Front Spring.

My front spring bottoms out when I go over a bump. I think my spring is getting weak and sagging (or maybe I broke a leaf).

In Les Andrew's 'Red Book' it states "measure the front end height from the center of the bumper to the ground. 1930/1931 should be 18½ +/- ½".

So I measure from the center of the two bars (center of the 'air space') to ground. Is this the correct spot?

I get 17¼", meaning my spring is sagging 1¼"?

I'm just checking because I'm not sure I am measuring in the correct spot.

Thanking in Advance...
Ruth is offline   Reply With Quote
Old 10-28-2019, 03:41 PM   #2
alexiskai
Senior Member
 
alexiskai's Avatar
 
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,329
Default Re: Sagging Front Spring.

I've often heard people say you should look at the spring shackles. On an ideal spring they're nearly horizontal, whereas on a worn-out spring they'll be nearly vertical. In extreme cases the shackle will hit the front axle and you'll see the wear marks. If there's less than 1/4" clearance between the axle and the shackle, people often consider that the cutoff point for spring replacement.
alexiskai is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 10-28-2019, 03:47 PM   #3
Werner
Senior Member
 
Werner's Avatar
 
Join Date: Jan 2019
Location: Germany, near Aachen
Posts: 1,151
Default Re: Sagging Front Spring.

Hallo Ruth,

I can not say anything about the reference points.

But it is unusual that a leaf spring tires. Is grease between the sheet layers? Are the suspensions freely movable on the outside?

When a single leaf is broken, it rattles in deep waves. Sometimes you can hear a break when you tap the hammer against a single spring leaf.
__________________
Beste Gruesse aus Deutschland,
Werner


Ford Model A, Roadster, 1928
Citroen 11 CV, 1947
Hercules W 2000, 1976; (with NSU-Wankel Rotary Engine), Canadian version
Werner is offline   Reply With Quote
Old 10-28-2019, 04:54 PM   #4
Ruth
Senior Member
 
Join Date: May 2016
Location: Glide, Oregon
Posts: 1,334
Default Re: Sagging Front Spring.

alexiskai, Yes looking at spring and shackles it clears the axle OK but I can see where the spring came into contact with the spring perch. At rest, the shackles are at ~70°, just short of being vertical.

I believe it is time for a new spring.

Werner, The current spring is lubed with graphite and has gaters to keep water & dirt out.
Ruth is offline   Reply With Quote
Old 10-31-2019, 01:24 PM   #5
100IH
Senior Member
 
Join Date: Dec 2011
Location: SW Idaho
Posts: 970
Default Re: Sagging Front Spring.

They do get old and loose their ability to support the weight. Re-arching is when each leaf is run through 3 rollers cold to bend into a taller stance. Usually only 1/2 effective and only for a short time.
100IH is offline   Reply With Quote
Old 10-31-2019, 01:44 PM   #6
WHN
Senior Member
 
Join Date: Mar 2017
Location: Connecticut Shoreline
Posts: 1,815
Default Re: Sagging Front Spring.

Sponsored Links (Register now to hide all advertisements)
My advice would be to replace front spring with a correct USA made one.

How would your TV recliner feel after 90 years of use. 24/365 not just 5 to 10? Enjoy.
WHN is offline   Reply With Quote
Old 10-31-2019, 02:48 PM   #7
Ruth
Senior Member
 
Join Date: May 2016
Location: Glide, Oregon
Posts: 1,334
Default Re: Sagging Front Spring.

Thanks Guys. I pulled the old spring and ordered new shackles and a USA made spring. I installed new bushings in the spring perches also.
Ruth is offline   Reply With Quote
Old 10-31-2019, 02:57 PM   #8
alexiskai
Senior Member
 
alexiskai's Avatar
 
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,329
Default Re: Sagging Front Spring.

If you have time, I'd love to hear which shackles you ordered and what tools were required for the bushings, as well as details of the install process going forward. I will need to replace my springs soon and I'm curious what level of expertise is needed.
alexiskai is offline   Reply With Quote
Old 10-31-2019, 04:58 PM   #9
Werner
Senior Member
 
Werner's Avatar
 
Join Date: Jan 2019
Location: Germany, near Aachen
Posts: 1,151
Default Re: Sagging Front Spring.

Hallo Alexis,

I have completely renewed the rear spring; that's comparable, I think?

The shackles and the spring were from Don Snyder III. The shackles fit without reworking in the bronze socket eyes of the spring. I have coated the individual spring layers with dry bonded coating with MoS2.

This work can be done well with some technical understanding.

For the front spring it shoud not necessarily to use a spring tensioner, there are some tricks. But I do not know if that can be dangerous.
__________________
Beste Gruesse aus Deutschland,
Werner


Ford Model A, Roadster, 1928
Citroen 11 CV, 1947
Hercules W 2000, 1976; (with NSU-Wankel Rotary Engine), Canadian version
Werner is offline   Reply With Quote
Old 10-31-2019, 05:17 PM   #10
Ruth
Senior Member
 
Join Date: May 2016
Location: Glide, Oregon
Posts: 1,334
Default Re: Sagging Front Spring.

Quote:
Originally Posted by alexiskai View Post
If you have time, I'd love to hear which shackles you ordered and what tools were required for the bushings, as well as details of the install process going forward. I will need to replace my springs soon and I'm curious what level of expertise is needed.
I have a hydraulic press that I used to remove and install the bushings in my spring perches (no doubt overkill). You could probably press them in with a large vice or 'C' clamp. The spring comes with the bushings installed. I may have to ream them, I don't know yet because I don't have the spring or shackles, yet.

Our club has tools we can borrow. I used their spring spreader to remove old spring. They also have a reamer for the bushings.
Ruth is offline   Reply With Quote
Old 10-31-2019, 07:02 PM   #11
alexiskai
Senior Member
 
alexiskai's Avatar
 
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,329
Default Re: Sagging Front Spring.

Hmm, OK, not going to be be super instructive for me. Likely will be doing it without spreader or press.
alexiskai is offline   Reply With Quote
Old 10-31-2019, 09:31 PM   #12
ahirt
Senior Member
 
Join Date: Nov 2014
Location: Stuart Florida
Posts: 108
Default Re: Sagging Front Spring.

I just changed my front spring. Not particularly difficult if you read Les' book. No spring spreader required. I had to get new spring perches as well as shackles and the new spring. All from Bratton's. No reaming was required.
I understand that the rear spring does require a spreader. I have had no need yet to do that spring so I cannot comment.
ahirt is offline   Reply With Quote
Old 10-31-2019, 09:39 PM   #13
Corley
Senior Member
 
Join Date: Aug 2011
Location: Battle Ground WA
Posts: 293
Default Re: Sagging Front Spring.

You may find the steering is much better after installing the new spring. When the shackles are almost vertical, the car car swing from side to side over the axle, and cause instability as it waddles down the road.
__________________
Corley
-----------------
Subscribed to the KISS principle!
Corley is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:36 AM.