|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
02-02-2019, 04:36 PM | #1 |
Member
Join Date: Feb 2015
Location: Big Island of Hawai`i
Posts: 43
|
Flywheel housing
Aloha all, I'm new to the "A" world. Just acquired mine in August of 18 from E-Bay. Seller wasn't totally honest and I've been having some issues and trying to work through them. What I need is a source of information with step by step directions to replace the flywheel housing on my 1931 coupe. It's badly cracked around the starter. Bought a new one from Snyders.
Thanks for any help |
02-02-2019, 04:44 PM | #2 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,751
|
Re: Flywheel housing
|
Sponsored Links (Register now to hide all advertisements) |
|
02-02-2019, 04:56 PM | #3 |
Senior Member
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
|
Re: Flywheel housing
Yep, that manual sure helps. I'm one that prefers to remove the rear end and transmission. I also prefer to leave the spring attached [ that spring can be dangerous if not handled correctly].
|
02-02-2019, 05:32 PM | #4 |
Member
Join Date: Feb 2015
Location: Big Island of Hawai`i
Posts: 43
|
Re: Flywheel housing
Thank you both
|
02-02-2019, 06:24 PM | #5 |
Senior Member
Join Date: May 2010
Location: Van, Texas
Posts: 1,122
|
Re: Flywheel housing
If the rear end and the transmission are removed - the engine is still attached to the Flywheel housing which is attached to the motor mounts which are attached to the frame. Also to get the housing off the flywheel will have to b e removed - a 65 lb toe crusher.
In this case I wouldd prefer to remove the engine for easy access to the flywheel and then the housing. LessAndreews book is an emense help in this case. |
02-05-2019, 11:07 AM | #6 |
Member
Join Date: Feb 2015
Location: Big Island of Hawai`i
Posts: 43
|
Re: Flywheel housing
Sponsored Links (Register now to hide all advertisements)
|
02-05-2019, 11:15 AM | #7 |
Senior Member
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,188
|
Re: Flywheel housing
I have always just pulled the engine/transmission together. Manifolds in place, transmission top removed/covered. If you have room to slip off the brake and clutch pedals this will help.
DON'T forget to undo the wish-bone attachment. I scratched my head over why the engine wouldn't come out with EVERY OTHER attachment removed - until I discovered I "missed" that one once. (My wife still laughs.) Spark plug No. 3 hole using a dead spark plug converted into lifting eye. Sheet metal cover for transmission held by bolts. Joe K
__________________
Shudda kept the horse. |
02-05-2019, 03:41 PM | #8 | |
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,513
|
Re: Flywheel housing
Quote:
Actually you are going to split the engine at the flywheel housing and the clutch (bell) housing. The clutch housing will remain bolted to the transmission. The transmission shift tower, the front radius rod (wishbone), and the clutch & brake pedals will NOT need to be removed or disconnected. You will need to remove the throttle assembly as it tries to interfere with the body when the engine is moving forward. |
|
02-06-2019, 04:55 PM | #9 |
Member
Join Date: Feb 2015
Location: Big Island of Hawai`i
Posts: 43
|
Re: Flywheel housing
Aloha all, This is a great forum and I truly appreciate all the feedback.
|
02-06-2019, 07:17 PM | #10 |
Senior Member
Join Date: May 2010
Location: Van, Texas
Posts: 1,122
|
Re: Flywheel housing
one mo thang. When you disconnect the Flywheel cover from the clutch bell housing, as you pull the engine forward the bell housing and transmission will want to drop - not much - maybe 1 to 2 inches. A floor jack under the tranny will hold it up where it belongs. If floor jack in not available a ratchet strap slung under the trans will also hold it up
|
02-06-2019, 09:14 PM | #11 |
BANNED
Join Date: Apr 2017
Location: Sacramento
Posts: 1,262
|
Re: Flywheel housing
Don't forget to dial it in..use horseshoe shims with gasket,if it doesnt run true remove horseshoes, if that makes it worse install horseshoes and remove gasket..if that works you can use RTV instead of the gasket. The reason you dial it in is proper crankshaft/transmission input shaft alignment,critical for smooth shifting and a smooth clutch |
02-06-2019, 10:43 PM | #12 | |
Senior Member
Join Date: May 2010
Location: The sticks of east Texas
Posts: 474
|
Re: Flywheel housing
Quote:
Picture is misleading since this check MUST be performed with the engine hanging nose down so that any end play in the crankshaft doesn't screw up the measurement of the flywheel housing, |
|
02-06-2019, 11:06 PM | #13 |
BANNED
Join Date: Apr 2017
Location: Sacramento
Posts: 1,262
|
Re: Flywheel housing
if you have enough crankshaft endplay to throw off the flywheel housing tolerance you have bigger issues than clutch alignment..youll be pouring babbit..
|
02-07-2019, 07:14 AM | #14 | |
Senior Member
Join Date: May 2010
Location: The sticks of east Texas
Posts: 474
|
Re: Flywheel housing
Quote:
The spec for crankshaft end play is OTOO .004" Since you're trying to get the FWH dialed to less than .006", letting the crank move renders the FWH measurements worthless. Last edited by BillLee/Chandler, TX; 02-07-2019 at 08:33 AM. |
|
02-08-2019, 12:30 AM | #15 |
BANNED
Join Date: Apr 2017
Location: Sacramento
Posts: 1,262
|
Re: Flywheel housing
Thats where your wrong,crankshaft end play, if present is a fixed deviation,an instant reading change on the indicator,where as mis alignment reads as a ramp increase as you travel to and away from the high side.
|
02-08-2019, 08:12 AM | #16 |
BANNED
Join Date: Apr 2017
Location: Sacramento
Posts: 1,262
|
Re: Flywheel housing
In the heavy duty truck world,this process is performed with the engine in the chassis,its a fairly common repair procedure...the same principal applies to the model A.The plane of the housing doesn't change with crankshaft endplay.
|
02-08-2019, 09:01 AM | #17 |
Senior Member
Join Date: May 2010
Location: Stuart Florida
Posts: 148
|
Re: Flywheel housing
I am a little confused. In post number 11 what is being aligned?
|
02-08-2019, 09:13 AM | #18 | |
Senior Member
Join Date: May 2010
Location: The sticks of east Texas
Posts: 474
|
Re: Flywheel housing
Quote:
That someone has lucked out on a large truck engine has no bearing here:this is a Model A engine we"RE talking about. |
|
02-08-2019, 09:28 AM | #19 |
Senior Member
Join Date: Apr 2015
Location: Saint Cloud Mn
Posts: 745
|
Re: Flywheel housing
Correct the plane does not change. The reading does however.
|
02-08-2019, 11:31 AM | #20 | ||
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,513
|
Re: Flywheel housing
.
Quote:
Quote:
Since both of y'all are my friends, I don't really want to take sides in this --AND I want to point out that both of you guys are correct ...however let's look at the overall picture and what is trying to be accomplished. Just as in the case with this Model-A the O/P is discussing, (--and with HD truck engines requiring service) it is a moot point about nosing the engine downward since it would require removing the engine from the chassis to do so. We all know that is not going to happen, so it may be best just to forgo and admit that both of you have valid points. Additionally, if the mechanic who is indicating the housing is purposely (-or even carelessly) pushing/pulling on the crankshaft during rotation, it is likely that the indicator readings will be flawed however this can also be done when the engine is nosed downward. So, how perfect does it need to be for this particular application? In restoration work, most good restorers strive for as much perfection as possible in their skill-set however in repair work, they just strive to be as accurate as possible in that particular environment. In this particular environment with the engine still mounted, I would try to get several readings that repeat and then go with it. . |
||
|
|
Sponsored Links (Register now to hide all advertisements) |
|