The Ford Barn

Lawson Cox · 01-29-2023, 01:39 PM

"Praise God from whom all blessings flow". I have the gasket installed correctly on one side of the distributor. I had to pull the wiring loom to get to it. On the little 60HP, that is a tough job with crooked fingers. I'll get the other side done, whenever. I'll try to get some pictures posted soon. (With somebody's help. LOL.)

JM 35 Sedan · 01-29-2023, 11:41 PM

Lawson, there are many of us here more than willing to help you post pictures. Just let us know when you are ready

Robert/Texas · 01-30-2023, 09:07 AM

Lawson, Here is what we did two years ago on my '34 Ford distributor. We couldn't get it all together with the wire looms attached so we pulled the wires out of them. The way we got the wires back into the looms was to attach baling wire to the sparkplug ends of each wire and flood the insides of the looms and all of the wires with silicone lubricant. Then we pulled the wires trough the looms, shortest ones first. I hope that this helps you.

Robert

Lawson Cox · 01-30-2023, 11:59 AM

Quote:

Originally Posted by Robert/Texas

Lawson, Here is what we did two years ago on my '34 Ford distributor. We couldn't get it all together with the wire looms attached so we pulled the wires out of them. The way we got the wires back into the looms was to attach baling wire to the sparkplug ends of each wire and flood the insides of the looms and all of the wires with silicone lubricant. Then we pulled the wires trough the looms, shortest ones first. I hope that this helps you.

Robert

Thanks Robert, but that part is already done.

01-29-2023, 01:39 PM	#41
Lawson Cox Senior Member Join Date: May 2010 Location: Above the gnat line in Georgia Posts: 6,934	Re: Distributor outer cap gaskets on dome distributors "Praise God from whom all blessings flow". I have the gasket installed correctly on one side of the distributor. I had to pull the wiring loom to get to it. On the little 60HP, that is a tough job with crooked fingers. I'll get the other side done, whenever. I'll try to get some pictures posted soon. (With somebody's help. LOL.) __________________ Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm". Last edited by Lawson Cox; 01-29-2023 at 08:14 PM.

01-29-2023, 11:41 PM	#42
JM 35 Sedan Senior Member Join Date: May 2010 Location: Near Rising Sun, Maryland Posts: 10,743	Re: Distributor outer cap gaskets on dome distributors Lawson, there are many of us here more than willing to help you post pictures. Just let us know when you are ready __________________ *John* *"Never give up on what you really want to do. The person with big dreams is more powerful than one with all the facts". Albert Einstein*

01-30-2023, 09:07 AM	#43
Robert/Texas Senior Member Join Date: May 2010 Location: Burton, Texas Posts: 646	Re: Distributor outer cap gaskets on dome distributors Lawson, Here is what we did two years ago on my '34 Ford distributor. We couldn't get it all together with the wire looms attached so we pulled the wires out of them. The way we got the wires back into the looms was to attach baling wire to the sparkplug ends of each wire and flood the insides of the looms and all of the wires with silicone lubricant. Then we pulled the wires trough the looms, shortest ones first. I hope that this helps you. Robert

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode