Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 01-18-2020, 04:50 PM   #1
Chris Haynes
Senior Member
 
Chris Haynes's Avatar
 
Join Date: May 2010
Location: Camarillo, CA and Pine Grove, CA
Posts: 2,830
Default Problem with front axle made of a mixture of parts.

My Axle is a 1933. The Spindles are 1937-1941. The Wishbone is a 1930. All is fitting together well, except the Tie Rod. Whether I mount the Tie Rod on top or bottom of the Spindle arm it hits the Wishbone. If mounted on the bottom it is smack in the middle of the wishbone. If on top it is about 1/2" into the top of the Wishbone.
Would it be safe to heat and bend the arms on the Spindles. Or make a Tie Rod with bends on the ends?

__________________
1921 Runabout
1930 Tudor
Early 1930 AA
Speed costs money. How fast do you want to go?
Chris Haynes is offline   Reply With Quote
Old 01-18-2020, 04:54 PM   #2
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: Problem with front axle made of a mixture of parts.

"Would it be safe to heat and bend the arms on the Spindles."

That's how it is done. Do not try to modify the tie rod ends! With a dropped axle you have to bend the arms if you are using original spindle arms.

Last edited by JSeery; 01-18-2020 at 09:44 PM.
JSeery is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 01-18-2020, 05:19 PM   #3
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Problem with front axle made of a mixture of parts.

That's gonna be NICE looking. Like JSeery said above, heating and bending those arms is the way guys have been doing it for 85 or so years now. When you heat them, be SURE to let them cool NATURALLY....no dousing with water or such. DD
__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 01-18-2020, 05:47 PM   #4
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: Problem with front axle made of a mixture of parts.

When you heat and bend, do so whilst maintaining correct Ackerman geometry.
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Old 01-18-2020, 07:14 PM   #5
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,070
Default Re: Problem with front axle made of a mixture of parts.

Willys tie rod ends of the era will drop your tie rod below the wishbone (the thread size is the same as used by Ford). Further, I seem to recall newly-made ones being available now.
DavidG is offline   Reply With Quote
Old 01-18-2020, 07:43 PM   #6
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,779
Default Re: Problem with front axle made of a mixture of parts.

Sponsored Links (Register now to hide all advertisements)
Brian beat me to mentioning to read up on the proper Ackerman if you don't know what it is.
deuce_roadster is offline   Reply With Quote
Old 01-18-2020, 09:07 PM   #7
Ol' Ron
Senior Member
 
Ol' Ron's Avatar
 
Join Date: May 2010
Location: Chester Vt
Posts: 8,842
Default Re: Problem with front axle made of a mixture of parts.

Just make sure you don't bend them in,or out. It will screw up the Ackerman angle.
Ol' Ron is offline   Reply With Quote
Old 01-18-2020, 09:15 PM   #8
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,260
Default Re: Problem with front axle made of a mixture of parts.

Speedway has the dropped tie rod ends. They say they are for '48-'60 Ford truck, but they will fit '37-'48 spindles.
tubman is offline   Reply With Quote
Old 01-18-2020, 10:34 PM   #9
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: Problem with front axle made of a mixture of parts.

Just make sure you don't bend them in,or out. It will screw up the Ackerman angle.


This all depends on the wheel base of the vehicle; quite conceivably you may have to bend in or out as well as down to maintain the correct geometry.
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Old 01-18-2020, 10:51 PM   #10
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Problem with front axle made of a mixture of parts.

Quote:
Originally Posted by Brian View Post
Just make sure you don't bend them in,or out. It will screw up the Ackerman angle.


This all depends on the wheel base of the vehicle; quite conceivably you may have to bend in or out as well as down to maintain the correct geometry.

Brian is absolutely correct when it comes to maintaining the correct Ackerman. It all depends on wheelbase length. DD
__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 01-19-2020, 12:04 AM   #11
RalphM
Senior Member
 
RalphM's Avatar
 
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,646
Default Re: Problem with front axle made of a mixture of parts.

Or, you could run the tie rod through the wishbone!
I have seen this done, but sorry, can’t find a picture now.
RalphM is offline   Reply With Quote
Old 01-19-2020, 08:17 AM   #12
john in illinois
Senior Member
 
john in illinois's Avatar
 
Join Date: May 2010
Location: Illinois
Posts: 2,181
Default Re: Problem with front axle made of a mixture of parts.

One thing to consider besides Ackerman is that the tie rod moves down as the wheel is turned. Need to check this. Also Okie Joe told me to bend at the root of the arm.

John
Attached Images
File Type: jpg 7EFFD7D0-755C-4C50-BA27-E69349197D62.jpg (71.9 KB, 61 views)
__________________
Welcome each day
john in illinois is offline   Reply With Quote
Old 01-19-2020, 09:20 AM   #13
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: Problem with front axle made of a mixture of parts.

If you're using a 34 type wishbone they favour the tie rod being above by the way they are shaped. You will need to retaper the holes in the spindles so the ends can go in from above and you will probably need to bend them up as well. As stated try and retain the ackermannn. Make sure you turn the spindles from lock to lock and maintain a clearance between the tie rod and the wishbone. There does not need to be a lot of clearance as long as there is some.

Re the tapers. Going half way from both sides is ok. It has been done many times before. You will need to buy or borrow a 7 degree taper reamer to do it.

Mart.
Mart is offline   Reply With Quote
Old 01-19-2020, 05:41 PM   #14
Chris Haynes
Senior Member
 
Chris Haynes's Avatar
 
Join Date: May 2010
Location: Camarillo, CA and Pine Grove, CA
Posts: 2,830
Default Re: Problem with front axle made of a mixture of parts.

Looking at the Speedway Dropped Tie rod ends it is hard to tell how far they drop the tie rod. I put it together and measured and this will solve my problem. Its just too bad they don't have them in stainless. :-(
__________________
1921 Runabout
1930 Tudor
Early 1930 AA
Speed costs money. How fast do you want to go?

Last edited by Chris Haynes; 01-19-2020 at 06:08 PM.
Chris Haynes is offline   Reply With Quote
Old 01-19-2020, 06:08 PM   #15
rich b
Senior Member
 
rich b's Avatar
 
Join Date: May 2010
Location: Minnesota
Posts: 1,813
Default Re: Problem with front axle made of a mixture of parts.

Bend the arms; those dropped tie rod ends are not very cool looking.

However; if you are limited in having an adequate torch; they may be something to consider. You will also need to narrow your tie rod as they take up more length.

Here is a picture that may give you an idea of how much they may lower the tie rod.
Attached Images
File Type: jpg dropped tie rod end.jpg (24.4 KB, 257 views)
rich b is offline   Reply With Quote
Old 01-19-2020, 06:56 PM   #16
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Problem with front axle made of a mixture of parts.

Yahoo...I had never seen those before. They look pretty damned substantial, and judging by the Mtn. Dew can in the background, look like something approaching a 2" drop. DD


__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 01-19-2020, 08:11 PM   #17
cas3
Senior Member
 
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,543
Default Re: Problem with front axle made of a mixture of parts.

ugly!!! real men bend the arms
cas3 is offline   Reply With Quote
Old 01-20-2020, 04:04 PM   #18
Tim Ayers
Senior Member
 
Join Date: May 2010
Location: NJ
Posts: 6,144
Default Re: Problem with front axle made of a mixture of parts.

Quote:
Originally Posted by DavidG View Post
Willys tie rod ends of the era will drop your tie rod below the wishbone (the thread size is the same as used by Ford). Further, I seem to recall newly-made ones being available now.
Came to say the same. I'll post picts. of what NOS ones look like. Get your wallet out. New ones are $150 a piece. I believe they are for a '37 Willys. Which ever the model year it was before they switched over to hydraulic brakes.
Tim Ayers is offline   Reply With Quote
Old 01-22-2020, 06:51 PM   #19
Bob/Ohio
Senior Member
 
Bob/Ohio's Avatar
 
Join Date: May 2010
Location: N.E.Ohio
Posts: 222
Default Re: Problem with front axle made of a mixture of parts.

I had the same problem on my AV8 and ended up buying Speedway dropped tie rod ends. Hangs a little lower than I like, but they fixed the problem. I have Speedway dropped steering arms, and I know they are not Ford quality, so I didn't want to try and bend them.


Bob
Bob/Ohio is offline   Reply With Quote
Old 01-22-2020, 07:44 PM   #20
Zeke3
Senior Member
 
Zeke3's Avatar
 
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,401
Default Re: Problem with front axle made of a mixture of parts.

Matt on Iron Trap Garage shows how to drop the steering arms on the 1939 Forgotten Hot Rod project episode 13. The steering arm work begins at the 8:25 mark.
https://www.youtube.com/watch?v=b9t-Ji3w6W4

The name Ackermann was not mentioned during the modification.
Zeke3 is offline   Reply With Quote
Old 01-23-2020, 03:09 PM   #21
Chris Haynes
Senior Member
 
Chris Haynes's Avatar
 
Join Date: May 2010
Location: Camarillo, CA and Pine Grove, CA
Posts: 2,830
Default Re: Problem with front axle made of a mixture of parts.

Quote:
Originally Posted by Zeke3 View Post
Matt on Iron Trap Garage shows how to drop the steering arms on the 1939 Forgotten Hot Rod project episode 13. The steering arm work begins at the 8:25 mark.
https://www.youtube.com/watch?v=b9t-Ji3w6W4

The name Ackermann was not mentioned during the modification.
Those guys are pretty crude. I can't imagine that all that heat isn't damaging the king pin bushings. The Mickey Mouse way they went about removing the rear spring shackle bushings is comical. Using a drill bit and a reamer instead of the correct tool shows a complete lack of professionalism.
__________________
1921 Runabout
1930 Tudor
Early 1930 AA
Speed costs money. How fast do you want to go?
Chris Haynes is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:05 AM.