The Ford Barn - View Single Post

haag1332 · 02-10-2015, 10:22 PM

Ok Folks, as far as I understand, the car club members reviewed the socket, and according to what I have been told, they all liked/loved it.

Hopefully tomorrow they will be providing their unbiased reviews on the 13/32" socket and what they really thought for all of you to read for your own edification.

It appears we can account for over 50 pieces at this point, so my plan will be to manufacture 100 in the first run. Subsequently in order to do this in a reasonable time frame I will be purchasing some different tooling. Having accounted for all the cost, and again, doing this for a labor of love and not making money, I am counting on getting my cost back with this run of 100 once they all sell. The different tooling will then allow for smaller runs after the first 100 at the same cost to the end user, if demand is there for whatever reason.

Again, hopefully everyone understands what it actually takes to produce this top quality socket without cutting any corners, and hopefully the club members who have put their hands on this socket will confirm this for you on this thread.

So here we go. The pricing we have decided on for the socket is $24.00 US Dollars plus shipping. Flat rate shipping through usps is approximately $6.00. And apparently you can order more than one, and it will still only be $6.00 for the shipping.

I am not asking anyone to pay anything now. It will take approximately 3 weeks to complete the run of 100 due to my current shop load, and schedule, as well as acquiring the blanks and tooling. Once they are complete, we will notify everyone individually who has expressed interest, as well as post it on this thread.

In the mean time, I realize some may not want to pay this much, which is fine. But would all of you who expressed interest, please reaffirm your interest at this point via this thread, private message, or email. I am assuming most will still be interested, but I don't wish to purchase tooling and such, and then end up in the hole on this project. I am also planning to pass this information along to each individual who expressed interest via private message or email as well.

I am not planning on purchasing the blanks or tooling till the end of the week just to make sure the interest is still there at this point. And it will take about a week maybe a little more to get the blanks.

Once the first run of 100 is complete, we will notify everyone who previously expressed or has re-expressed interest with regard to how to purchase. At this point purchasing will probably be via credit card through paypal unless other arrangements are made on an as need basis.

Bill Haag, Jr.

P.S. Thank you all for your interest in this project, I feel honored to be able to help with this apparent need.

02-10-2015, 10:22 PM	#64
haag1332 Senior Member Join Date: Feb 2015 Posts: 120	Re: carburetor 13/32 deep well socket Ok Folks, as far as I understand, the car club members reviewed the socket, and according to what I have been told, they all liked/loved it. Hopefully tomorrow they will be providing their unbiased reviews on the 13/32" socket and what they really thought for all of you to read for your own edification. It appears we can account for over 50 pieces at this point, so my plan will be to manufacture 100 in the first run. Subsequently in order to do this in a reasonable time frame I will be purchasing some different tooling. Having accounted for all the cost, and again, doing this for a labor of love and not making money, I am counting on getting my cost back with this run of 100 once they all sell. The different tooling will then allow for smaller runs after the first 100 at the same cost to the end user, if demand is there for whatever reason. Again, hopefully everyone understands what it actually takes to produce this top quality socket without cutting any corners, and hopefully the club members who have put their hands on this socket will confirm this for you on this thread. So here we go. The pricing we have decided on for the socket is $24.00 US Dollars plus shipping. Flat rate shipping through usps is approximately $6.00. And apparently you can order more than one, and it will still only be $6.00 for the shipping. I am not asking anyone to pay anything now. It will take approximately 3 weeks to complete the run of 100 due to my current shop load, and schedule, as well as acquiring the blanks and tooling. Once they are complete, we will notify everyone individually who has expressed interest, as well as post it on this thread. In the mean time, I realize some may not want to pay this much, which is fine. But would all of you who expressed interest, please reaffirm your interest at this point via this thread, private message, or email. I am assuming most will still be interested, but I don't wish to purchase tooling and such, and then end up in the hole on this project. I am also planning to pass this information along to each individual who expressed interest via private message or email as well. I am not planning on purchasing the blanks or tooling till the end of the week just to make sure the interest is still there at this point. And it will take about a week maybe a little more to get the blanks. Once the first run of 100 is complete, we will notify everyone who previously expressed or has re-expressed interest with regard to how to purchase. At this point purchasing will probably be via credit card through paypal unless other arrangements are made on an as need basis. Bill Haag, Jr. P.S. Thank you all for your interest in this project, I feel honored to be able to help with this apparent need.