Forum: Early V8
10-11-2016, 06:50 PM
|
Replies: 2
Views: 1,726
|
Forum: Early V8
10-11-2016, 06:47 PM
|
Replies: 2
Views: 1,726
|
Forum: Early V8
09-07-2016, 02:55 PM
|
Replies: 2
Views: 1,726
1932 ford V8 Motor Complete
I have a complete 1932 ford Flathead motor (straight down drains), from the air cleaner to oil pan, including a 32 trans that came out of a AACA award winning 3W the motor had less than 1000 miles...
|
Forum: Early V8
06-21-2012, 06:37 PM
|
Replies: 3
Views: 1,715
|
Forum: Early V8
04-20-2012, 07:05 AM
|
Replies: 4
Views: 1,065
|
Forum: Early V8 (1932-53)
04-12-2012, 09:23 PM
|
Replies: 5
Views: 1,108
|
Forum: Early V8 (1932-53)
04-12-2012, 07:26 PM
|
Replies: 5
Views: 1,108
38 throwout bearing part number
Does any one have a modern part number for a 36-48 throwout bearing and hub? I hot one today from the local parts supplier, and the hole in the center is too small.
|
Forum: Early V8 (1932-53)
04-02-2012, 11:20 AM
|
Replies: 208
Views: 97,133
|
Forum: Early V8
03-26-2012, 02:24 PM
|
Replies: 4
Views: 1,065
|
Forum: Early V8 (1932-53)
03-26-2012, 02:20 PM
|
Replies: 38
Views: 10,432
|
Forum: Early V8
02-27-2012, 07:26 AM
|
Replies: 2
Views: 919
|
Forum: Early V8 (1932-53)
02-21-2012, 10:43 PM
|
Replies: 16
Views: 11,412
Re: EAB Flathead crank pulleys and intakes
I talked with a friend from Denmark, and he used a French Flathead in a stock 32 frame, and raised the front up 3/4" ad was able to clear the double pulley. I'm not sure if they are exactly the same...
|
Forum: Early V8 (1932-53)
02-21-2012, 08:03 AM
|
Replies: 13
Views: 2,839
Re: A sad reality...FIRE
Hope everyone was OK, but I'm not sure a small carry along fire extinguisher would have saved that one.
|
Forum: Early V8 (1932-53)
02-20-2012, 07:14 PM
|
Replies: 16
Views: 11,412
Re: EAB Flathead crank pulleys and intakes
It's the rear shive that I am having clearance issues with on my crossmember, I am going to buy another late truck crank pulley an see what needs to be trimmed to clear it
|
Forum: Early V8 (1932-53)
02-20-2012, 05:23 PM
|
Replies: 16
Views: 11,412
Re: EAB Flathead crank pulleys and intakes
Is there a difference between the late truck pumps and what I currently have? The 39 pulley goes inside of the cam gear cover correct? My pulley stops at the cover, I think there is a ring that is...
|
Forum: Early V8 (1932-53)
02-20-2012, 04:31 PM
|
Replies: 16
Views: 11,412
Re: EAB Flathead crank pulleys and intakes
I think the biggest issue I have is the intake, it does not have enough clearance for a generator in the stock location, and I'm assuming that the breather tube needs to be over the tube that is in...
|
Forum: Early V8 (1932-53)
02-20-2012, 03:59 PM
|
Replies: 16
Views: 11,412
EAB Flathead crank pulleys and intakes
I posted this on the HAMB, but got no response.
I have just started mocking up my Deuce Tudor engine, and I from all the searching I have done cannot figure out what crankshaft pulley to use, the...
|
Forum: Early V8 (1932-53)
02-15-2012, 02:01 PM
|
Replies: 27
Views: 8,435
Re: Extremely Rare Winfield Head for A/B/C
I believe he is in Mojave, CA and his shop is at 8201 Sierra Hwy, Mojave, CA TEL: (661) 824-4728
That is a very cool find, my father has an original Riley 2 port head on his...
|
Forum: Early V8 (1932-53)
02-15-2012, 08:04 AM
|
Replies: 2
Views: 1,375
Tudor roof tack strip insert
I'm in the process of removing the original tack strip and roof wood to redo the insert on my 32 Tudor, my question is after the roof material is tacked down, and the tack strip is tacked on, was...
|
Forum: Early V8 (1932-53)
02-14-2012, 09:50 AM
|
Replies: 48
Views: 8,977
Re: Ebay Idiots
I bought a "NOS" Purolator filter on FLEABAY for my stepdown Hudson, when it came it had been spray bombed red, and a crappy job at that, no biggy, I would have bought it anyway but not for what I...
|
Forum: Early V8
02-13-2012, 03:52 PM
|
Replies: 2
Views: 919
|
Forum: Early V8 (1932-53)
02-10-2012, 05:16 PM
|
Replies: 49
Views: 11,359
Re: found this today
I wish there was still stuff like that here on the east coast, nothing but piles of rust for us to pick over!
|
Forum: Early V8
02-09-2012, 09:51 AM
|
Replies: 2
Views: 919
WTB 32 Ford parts
Wanted, '32 Tudor steel fenders, Tudor rear 1/4 garnish moldings '32 drivers door, '32 hood latches, 2 16x4 wheels PM me here.
|
Forum: Early V8
01-05-2012, 06:43 AM
|
Replies: 4
Views: 1,065
|
Forum: Early V8
01-04-2012, 04:20 PM
|
Replies: 4
Views: 1,065
|