Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.04 seconds.
Search: Posts Made By: Drive Shaft Dave
Forum: Model A (1928-31) 08-22-2019, 10:58 PM
Replies: 18
Views: 854
Posted By Drive Shaft Dave
Re: Motor Suddenly Stuck

This is one of those times when a block of wood and a very large whammer is your friend
...
Forum: Model A (1928-31) 08-17-2019, 11:07 PM
Replies: 14
Views: 571
Posted By Drive Shaft Dave
Re: New clutch - should the throw out bearing disengage?

Yes, if you are pushing the clutch pedal to the floor it will spin. how close is the throw out bearing when the pedal is released?
Forum: Model A (1928-31) 05-29-2019, 09:45 PM
Replies: 3
Views: 365
Posted By Drive Shaft Dave
Re: rear brake single shoe ,emerg brake history

In the case of the ModelA,the revised rear brakes came with a stepped drum to accomodate the emergency brake band. The early models simply picked up the service brake with the hand brake lever. As...
Forum: Model A (1928-31) 03-30-2019, 01:52 AM
Replies: 32
Views: 1,886
Posted By Drive Shaft Dave
Re: How much grease in the clamshell?

I just remove one of the bolts.
Forum: Model A (1928-31) 03-19-2019, 01:44 AM
Replies: 8
Views: 557
Posted By Drive Shaft Dave
Re: Trunk floor pan

The same part is used for both configurations.
Forum: Model A (1928-31) 02-27-2019, 01:31 AM
Replies: 10
Views: 1,038
Posted By Drive Shaft Dave
Re: Rear Hub Grease Seal Removal Tool

I have used the Tom Endy method for years , works good.
Forum: Model A (1928-31) 02-27-2019, 01:24 AM
Replies: 5
Views: 460
Posted By Drive Shaft Dave
Re: 31 Coupe Wood (Under side window)

upholstery panel nails to this.
Forum: Early V8 (1932-53) 02-02-2019, 08:34 PM
Replies: 11
Views: 988
Posted By Drive Shaft Dave
Re: What is this puller part for ???

The puller is used to remove rear drums and hub from tapered axle shafts. I didn't read the compete thread . I dont know what the other part is. Tried to delete but wouldn't take.
Forum: Model A (1928-31) 02-02-2019, 08:30 PM
Replies: 54
Views: 4,478
Posted By Drive Shaft Dave
Re: Ford Tri-Motor

Actually the Harvard was a different airplane, although a trainer with fixed gear.
Forum: Model A (1928-31) 02-01-2019, 09:10 PM
Replies: 12
Views: 904
Posted By Drive Shaft Dave
Re: Engine mount rubber replacement

Brattons cataloge pg. 35, 2018, shows motor mount rubbers made to the Ford print. while I have not tried these, the last mount 's I put in , made use of some dish soap and they slid in quite...
Forum: Model A (1928-31) 01-14-2019, 12:14 AM
Replies: 2
Views: 380
Posted By Drive Shaft Dave
Forum: Model A (1928-31) 01-07-2019, 12:24 AM
Replies: 42
Views: 2,717
Posted By Drive Shaft Dave
Re: Water Temperature Gauge

I have heard that the rex aco temp gauge has been problematic in the last few years .
Forum: Model A (1928-31) 01-07-2019, 12:09 AM
Replies: 8
Views: 1,664
Posted By Drive Shaft Dave
Re: Tom Wesenberg

Yes he is ok. just taking a look around the country side.
Forum: Model A (1928-31) 12-07-2018, 08:11 PM
Replies: 1
Views: 343
Posted By Drive Shaft Dave
Re: Need clarification...Bolts and Toggle Lever...

fine thread on the Spring Bolts, Toggle lever , drive in.
Forum: Model A (1928-31) 12-06-2018, 11:20 PM
Replies: 56
Views: 3,648
Posted By Drive Shaft Dave
Re: Weld and grind roller tracks

It is more of a hassle to replace them , weld then file or use die grinder.
Forum: Model A (1928-31) 12-02-2018, 01:54 AM
Replies: 11
Views: 1,178
Posted By Drive Shaft Dave
Re: 7.0 Earthquake in Anchorage Alaska

Alaska had a bad one in 1964 I remember. Was 9.2 on the Richter scale.
Forum: Model A (1928-31) 11-28-2018, 12:32 AM
Replies: 5
Views: 700
Posted By Drive Shaft Dave
Re: Tail pipe stub

Muffler shop could make one.
Forum: Model A (1928-31) 11-28-2018, 12:30 AM
Replies: 57
Views: 4,720
Posted By Drive Shaft Dave
Re: Stroke

Hang in there Bill!
Forum: Model A (1928-31) 10-18-2018, 10:10 PM
Replies: 8
Views: 773
Posted By Drive Shaft Dave
Re: Ignition switch

Disconnect the light and horn wire from the cut out then try it, you most likely have socket grounded .
Forum: Model A (1928-31) 09-21-2018, 01:16 PM
Replies: 23
Views: 2,326
Posted By Drive Shaft Dave
Re: coils question

How about Chev 6 cyl. they were always mounted terminals down.
Forum: Model A (1928-31) 09-21-2018, 12:26 AM
Replies: 18
Views: 1,504
Posted By Drive Shaft Dave
Re: Fan Blade advice.

make shure you use a flat steel washer under the mounting nut on an aluminum fan.
Forum: Model A (1928-31) 09-21-2018, 12:12 AM
Replies: 15
Views: 1,410
Posted By Drive Shaft Dave
Re: Another Gas Tank and Headlight question

If you put in sealer there will come a day you wish you hadn't.
Forum: Model A (1928-31) 09-06-2018, 11:32 PM
Replies: 3
Views: 670
Posted By Drive Shaft Dave
Smile Re: Might have screwed up

I doubt that you hurt anything.:)
Forum: Model A (1928-31) 08-22-2018, 11:50 PM
Replies: 20
Views: 1,927
Posted By Drive Shaft Dave
Re: Is this an 'A'?

I't is a Chevrolet.
Forum: Model A (1928-31) 08-18-2018, 12:27 AM
Replies: 14
Views: 1,274
Posted By Drive Shaft Dave
Re: Original ammeter or repop?

I bought one of those on flea bay a few years back, had the bezel nickle plated.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 11:11 AM.