The Ford Barn
FordBarn.com
The Forum
Swap
About
Register
Calendar
Members List
Search
Today's Posts
Mark Forums Read
FAQ
The Ford Barn
>
Search Forums
Search Results
User Name
Remember Me?
Password
Sponsored Links (Register now to hide all advertisements)
Showing results 1 to 11 of 11
Search took
0.00
seconds.
Search:
Posts Made By:
Club Coupe
Forum:
Early V8 (1932-53)
04-01-2021, 07:42 AM
Replies:
6
shifts hard
Views:
943
Posted By
Club Coupe
Re: shifts hard
Thanks to all of you for your replies. I'll start removing all the small parts tomorrow and clean and lubricate them before reassembly. I would start today but it's that time of year for my first...
Forum:
Early V8 (1932-53)
03-31-2021, 04:38 PM
Replies:
6
shifts hard
Views:
943
Posted By
Club Coupe
Re: shifts hard
Thanks, Bob. Looks like I need to pull the entire steering column out. Rats!
Forum:
Early V8 (1932-53)
03-31-2021, 03:57 PM
Replies:
6
shifts hard
Views:
943
Posted By
Club Coupe
shifts hard
1950 Club Coupe. Shifting from first to second I raise the shift arm up to neutral and the spring does not pull the lever down to go on into second. I must push it forward then on into second It has...
Forum:
Early V8 (1932-53)
10-21-2020, 07:46 PM
Replies:
3
knob on choke cable
Views:
799
Posted By
Club Coupe
Re: knob on choke cable
Thank you both. I plan to reuse the know so I will try that tomorrow.
Forum:
Early V8 (1932-53)
10-21-2020, 04:40 PM
Replies:
3
knob on choke cable
Views:
799
Posted By
Club Coupe
knob on choke cable
I have a bad choke cable on my 1950 Ford. I can't get the old knob off. I tried screwing it off and pulling it straight off but nothing gives. What am I doing wrong? Can one of you advise me?
Forum:
Early V8 (1932-53)
01-04-2020, 06:51 PM
Replies:
4
Dtill a hole in the floor?
Views:
1,307
Posted By
Club Coupe
Re: Drill a hole in the floor?
Thanks, 40cpe. At least I will know the hole's in the right place.
Forum:
Early V8 (1932-53)
01-04-2020, 06:38 PM
Replies:
4
Dtill a hole in the floor?
Views:
1,307
Posted By
Club Coupe
Dtill a hole in the floor?
I am considering installing an OD tranny in my 1950 Ford. I have been offered one for $700which has been pro rebuilt. After doing some reading and Youtubing it looks like (among several other things)...
Forum:
Model A (1928-31)
01-04-2020, 05:40 PM
Replies:
3
a hole in my floorboard??!!
Views:
1,460
Posted By
Club Coupe
a hole in my floorboard??!!
I am considering putting an OD tranny in my 1950 Ford. I have a rebuilt one available for $700. After reading and watching YouTube videos it seems that (among other things) I will need to drill a...
Forum:
Questions & Suggestions
01-04-2020, 02:24 PM
Replies:
1
A hole in my floorboard???
Views:
1,257
Posted By
Club Coupe
A hole in my floorboard???
I am considering installing an OD tranny in my '50 club coupe. I have been offered a rebuilt one for $700. After doing a little research, it looks like I may have to drill a hole in my floorboard for...
Forum:
Early V8 (1932-53)
11-23-2019, 09:20 PM
Replies:
14
gear ratio
Views:
2,493
Posted By
Club Coupe
Re: gear ratio
Thanks, friends. I'm sure this will not work in my '50. I just wondered what car had a gearing that high. I would have to get a push to take off even if it did fit. But I will tell the owner of the...
Forum:
Early V8 (1932-53)
11-22-2019, 01:00 PM
Replies:
14
gear ratio
Views:
2,493
Posted By
Club Coupe
gear ratio
An acquaintance is trying to give me a differential for my 1950 Ford. It has 15 teeth on the pinion and 42 on the ring gear.
By my calculations that is a 2.80 ratio. Obviously I can't use it but I...
Showing results 1 to 11 of 11
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General Discussion
Model T (1909-1927)
Model A (1928-31)
Early V8 (1932-53)
Late V8 (1954+)
Hot Rods & Customs
The Swap Meet
For Sale
Model-T
Model-A
Early V8
Late V8
The Jalopy Auction House
To The Editors
Questions & Suggestions
The Test Forum
The Archives
Model-T
Model-A
Early V8
Late V8
Sponsored Links (Register now to hide all advertisements)
All times are GMT -5. The time now is
08:12 PM
.