Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 160
Search took 0.01 seconds.
Search: Posts Made By: Flatout
Forum: Early V8 (1932-53) 09-12-2018, 05:31 AM
Replies: 24
Views: 2,673
Posted By Flatout
Forum: Early V8 (1932-53) 09-12-2018, 05:12 AM
Replies: 10
Views: 1,037
Posted By Flatout
Re: 3 speed column shift grinding in 3rd-Help!

What gear oil are you using? Some oils specifically state in small print on the back "not for use in synchromesh transmissions"
Use GL-1 in your transmission. NAPA carries it. It's straight 90 wt. ...
Forum: Early V8 (1932-53) 07-04-2018, 03:46 PM
Replies: 7
Views: 2,043
Posted By Flatout
Re: Rare? 1932 Chassis

I had one years ago. Serial Number 18-352
Forum: Early V8 (1932-53) 06-23-2018, 07:37 AM
Replies: 15
Views: 1,938
Posted By Flatout
Re: flow direction in slingshot manifold

I'm running my slingshot with progressive linkage on the carbs. It operates like a single 4-barrel carb. For reduced fuel consumption on a trip, I slide a shim under the secondary carb to block it....
Forum: Early V8 (1932-53) 04-15-2018, 02:58 PM
Replies: 49
Views: 7,192
Posted By Flatout
Re: Engine problem or normal?

The oil line from the block to the filter should have a restriction to limit oil flow and loss of oil pressure. I've found that about .060" diameter hole will be enough flow for the filter without...
Forum: Early V8 (1932-53) 02-21-2018, 05:07 PM
Replies: 4
Views: 1,008
Posted By Flatout
Re: 10M made in Canada heads

The Mercury heads did not have a reduction in chamber volume. That would have resulted in an increase in compression over Fords. Mercury heads had an enlargement in chamber volume, to reduce...
Forum: Early V8 (1932-53) 02-10-2018, 02:07 AM
Replies: 32
Views: 3,296
Posted By Flatout
Re: Was there a 4 cylinder motor in 34

The 33-34 B engines have a different front timing gear cover, crank pulley, water pump, and front motor mount from 32 B's. These parts make the front of the motor shorter to clear the rear sloping...
Forum: Early V8 (1932-53) 01-29-2018, 02:22 AM
Replies: 20
Views: 1,925
Posted By Flatout
Re: 40 Ford to 40 Merc rear swap

If the drive shaft lengths are the same, probably. Some early Mercury inner drive shafts are one piece with the pinion gear, and if the shaft is too long, you've got a problem altering it.
Forum: Early V8 (1932-53) 09-24-2017, 09:48 PM
Replies: 10
Views: 1,314
Posted By Flatout
Re: Cast brass heads

I've seen iron heads polished and brass plated, but that over 60 years ago.

I have a couple sets of Federal Mogul heads that are are cast bronze with aluminum tops, and they do have water...
Forum: Early V8 (1932-53) 09-09-2017, 10:01 PM
Replies: 21
Views: 3,050
Posted By Flatout
Re: Fakin a Merc !

You may have the wrong starter plate. The starter should be perpendicular (90 degrees) to the flywheel. I had the same problem 50 years ago.
Be sure the flywheel is the one for the late engine. If...
Forum: Early V8 (1932-53) 09-06-2017, 01:48 AM
Replies: 23
Views: 3,500
Posted By Flatout
Re: OHC Flathead

George Riley built some ohc engines that used Ford cranks, rods, and pistons, and pan. I think Riley made all other major comments.
Forum: Early V8 (1932-53) 09-06-2017, 01:42 AM
Replies: 23
Views: 3,500
Posted By Flatout
Re: OHC Flathead

Ford engineering, in the late 30's or early 40's made 10 ohc engines based on the flathead block. The idea was to develop design ideas for the future. It's been reported that Henry ordered them to be...
Forum: Early V8 (1932-53) 09-06-2017, 01:24 AM
Replies: 6
Views: 1,188
Posted By Flatout
Re: Heders

Fenton made several models to fit a wide range of years. Those models had different part numbers cast onto them.
Reproduction Fenton headers, made by Fenton, and others, come in only one model, and...
Forum: Early V8 (1932-53) 09-06-2017, 01:13 AM
Replies: 22
Views: 4,307
Posted By Flatout
Re: 1949 Mercury differential ratios?

In the 60's I had a 51 Merc with the auto trans. The rear had 3:07 gears.
Forum: Early V8 (1932-53) 06-16-2017, 09:37 AM
Replies: 2
Views: 710
Posted By Flatout
Re: Federal Mogal Heads - No Water Pumps Needed

I've only seen them in 3 styles.
32-36. They have water pump flanges, and water jackets, and a 2-piece design.
37, early 38, 21 stud. Those engines have water pumps in the block. The heads have...
Forum: Early V8 (1932-53) 05-04-2017, 03:15 AM
Replies: 17
Views: 2,069
Posted By Flatout
Re: Pacific Northwest visit

If you visit the Portland area, send me a message. My last Colorado visitor was Rumble Seat. I enjoyed his visit. We both similar medical issues, but he liked the junk in my garage.
Stan
Forum: Early V8 (1932-53) 04-02-2017, 09:02 PM
Replies: 4
Views: 885
Posted By Flatout
Re: pulling stock 32 engine

As DavidG says, there are no "ears" on the crossmember face to support the transmission mount.
But there is a short pin on the crossmember face, on either side that would seem to perform that...
Forum: Early V8 (1932-53) 04-02-2017, 08:36 PM
Replies: 8
Views: 1,242
Posted By Flatout
Re: Fitting A 40 diff into a 34 chassis

A small amount of grinding on the rear of the straight spring will allow it to slip right into the crossmember. Even less is needed to fit into a 32 crossmember.
I've done this several times over...
Forum: Early V8 (1932-53) 02-19-2017, 02:54 AM
Replies: 10
Views: 1,358
Posted By Flatout
Re: 33/34 Pickup difference?

Sales were slow in these depression years. Unsold units were left over, and often titled in the year that were actually sold. This has resulted confusion in later years, as to what model year the...
Forum: Early V8 (1932-53) 01-03-2017, 10:51 PM
Replies: 61
Views: 15,358
Posted By Flatout
Re: Isky 404A cam - Harley Davidson grind?

I believe Isky's 404 grinds are an adaptation of Ed Winfield's number 4 profile for Offenhauser 4-cylinder engines. Offenhauser engines used radius lifters.
Potvin called his version "Eliminator",...
Forum: Early V8 (1932-53) 12-11-2016, 02:18 AM
Replies: 4
Views: 1,160
Posted By Flatout
Re: Remove V8 oil pan on a '37 Ford Sedan

I did it on my 37 in 1964.
Jack up the car by the frame so that the front suspension hangs down.
Jack up the engine.
It will come off by dropping and rotating it.
Forum: Early V8 (1932-53) 11-11-2016, 10:00 PM
Replies: 40
Views: 6,630
Posted By Flatout
Re: 1940 Pickup w / 4 speed serial number?

The serial number on my 4-speed bell housing has a "BB 18" prefix. It is from a 1932 truck with a 4-cylinder engine. The number is stamped on a cast raised pad that looks like the normal place for...
Forum: Early V8 (1932-53) 10-26-2016, 10:48 PM
Replies: 18
Views: 1,713
Posted By Flatout
Re: 34 manifold to stock 32 engine

I would recommend using a 37 intake on a 32 engine if it's installed in a 32. The original 32 intake mounts the generator down low, as does the 37 intake. This positions the fan blades low enough to...
Forum: Early V8 (1932-53) 10-25-2016, 08:21 PM
Replies: 19
Views: 2,436
Posted By Flatout
Re: 1952 Fordomatic rear-end ratio?

My 51 "Mercomatic" had a 3:07. That was in 1960. I can't say if it was factory installed or not. When I put a stick in it, it had to go. I had to downshift for every hill.
Forum: Early V8 (1932-53) 10-05-2016, 07:47 PM
Replies: 16
Views: 1,537
Posted By Flatout
Re: Help Identifying Early Ford Juice Brakes

Backing plates are 39-42 design.
Showing results 1 to 25 of 160

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:14 PM.