Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 14 of 14
Search took 0.00 seconds.
Search: Posts Made By: feufeu
Forum: Early V8 (1932-53) 05-26-2021, 12:08 PM
Replies: 24
Views: 799
Posted By feufeu
Re: Turn signal and brake light problems

ground or repeater for the 7th?
Forum: Early V8 (1932-53) 05-25-2021, 02:22 PM
Replies: 24
Views: 799
Posted By feufeu
Re: Turn signal and brake light problems

you could test it with voltmeter?
Forum: Early V8 (1932-53) 05-25-2021, 02:20 PM
Replies: 24
Views: 799
Posted By feufeu
Re: Turn signal and brake light problems

typical schematic for flasher
Forum: Early V8 (1932-53) 05-25-2021, 02:05 PM
Replies: 24
Views: 799
Posted By feufeu
Re: Turn signal and brake light problems

Hi Mikko,
I think bad ground for LH and perhaps flasher issue...
Forum: Early V8 (1932-53) 02-09-2021, 10:10 AM
Replies: 42
Views: 2,113
Posted By feufeu
Re: My old red tonner on a music video.

Really nice song and pictures!
congratulations!
Forum: Early V8 (1932-53) 01-22-2021, 03:03 AM
Replies: 6
Views: 610
Posted By feufeu
Re: Parts identification help, please.

That's my 37 column drop.

Feufeu.
Forum: Early V8 (1932-53) 01-02-2021, 04:17 AM
Replies: 14
Views: 670
Posted By feufeu
Re: Adapting An OE Gas Tank Sender Unit

Be careful, on my tudor 37 I made a rubber gasket between the sending unit and the tank. Some days later it was smelling gas in the car... the rubber was melt by gasoline...
Forum: Early V8 (1932-53) 11-23-2020, 03:44 AM
Replies: 15
Views: 883
Posted By feufeu
Re: Temperature

Kevin, I think like Alan; your stats are operating correctly!
mine are 160F so they are closed until the temperature is 160F; at this temperature they open and let the coolant circulate so the...
Forum: Early V8 (1932-53) 11-18-2020, 02:12 AM
Replies: 12
Views: 999
Posted By feufeu
Re: 1936 radiator petcock

Yes it's very difficult to solder a radiator because the two boxes (top & bottom) are tin soldered, so if you heat too much the result will be leaks.
feufeu.
Forum: Early V8 (1932-53) 11-16-2020, 05:41 AM
Replies: 12
Views: 999
Posted By feufeu
Re: 1936 radiator petcock

I had the same issueon my 37 radiator. wanted to replace the petcok and i broke it.
So i drilled a hole of 18mm in the radiator, and put in the hole a brass part I made. The internal of the part...
Forum: Early V8 (1932-53) 11-14-2020, 08:02 AM
Replies: 19
Views: 1,200
Posted By feufeu
Re: Mechanical Oil pressure gauge fittings

I ve never seen these type...
Don't you know anybody with a lathe. It can be made...
Forum: Early V8 (1932-53) 11-14-2020, 04:22 AM
Replies: 8
Views: 1,142
Posted By feufeu
Re: Some ignition slides i found today ??

Same for me. I asked acces
Forum: Early V8 (1932-53) 10-16-2020, 12:41 PM
Replies: 16
Views: 1,138
Posted By feufeu
Re: connector sleeve for choke rod

...or crimped as said Viv
Forum: Early V8 (1932-53) 10-16-2020, 12:37 PM
Replies: 16
Views: 1,138
Posted By feufeu
Re: connector sleeve for choke rod

Hi Tom, in my 37 there is a piece connecting the two parts of the rod. You can see it in the red circles on the picture (picture under dash).
Sorry for my english, i'm french!
I couldnt...
Showing results 1 to 14 of 14

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:50 PM.