Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: GOSFAST
Forum: Early V8 (1932-53) 12-02-2019, 12:23 PM
Replies: 70
Views: 2,922
Posted By GOSFAST
Re: Early V8 Dyno Work

Maybe I can help a bit with some numbers. The following info is from the ride in my signature below here. Also placed 2 shots below!

My very good friend Ron House, owner of this ride, a '50 Merc...
Forum: Early V8 (1932-53) 11-30-2019, 01:05 PM
Replies: 5
Views: 380
Posted By GOSFAST
Re: Video putting a sleeve in a flathead

I would've recommended putting some "green" #675 Loctite on that sleeve before installing it, if there happened to any very slight pin holes the Loctite would become the sealer!

Believe it or...
Forum: Early V8 (1932-53) 11-25-2019, 11:58 AM
Replies: 25
Views: 1,318
Posted By GOSFAST
Re: For those with machining experience. Sleeve fitting??

Hi Dale, the CNC is in my friends building, I didn't have the room where I am now, it takes up a lot "real-estate"!

He works closely with me and my son, I don't like using it, downright "boring",...
Forum: Early V8 (1932-53) 11-24-2019, 05:49 PM
Replies: 25
Views: 1,318
Posted By GOSFAST
Re: For those with machining experience. Sleeve fitting??

Hi Mart, first item I would check assuming a deck-mounted bar here, I would recommend somehow mounting a dial indicator on the column down near where the cutter mounts.

Run the cutter head down...
Forum: Early V8 (1932-53) 11-21-2019, 09:48 AM
Replies: 40
Views: 1,315
Posted By GOSFAST
Re: Flathead Lifter Adjusting - "On the Bench"

Heads up guys, my intention here is NOT to "redesign the wheel", it's to make some of the existing procedures that most of us have become accustomed to on the Flatheads a bit easier accomplish!
...
Forum: Early V8 (1932-53) 11-19-2019, 07:53 PM
Replies: 40
Views: 1,315
Posted By GOSFAST
Re: Flathead Lifter Adjusting - "On the Bench"

Hi Dale, yes, on the top, and once I spotted this and thought about it, even before I called Dave at "Topline", I knew it MUST have that crown in order to work the way it is designed now! There's a...
Forum: Early V8 (1932-53) 11-19-2019, 03:14 PM
Replies: 40
Views: 1,315
Posted By GOSFAST
Re: Flathead Lifter Adjusting - "On the Bench"

The info I'm putting here today is more-or-less a "tip" about using the original Johnson tappets from Topline-Automotive, just got off the phone with Dave and learned something even I wasn't aware of...
Forum: Early V8 (1932-53) 11-18-2019, 05:14 PM
Replies: 40
Views: 1,315
Posted By GOSFAST
Re: Flathead Lifter Adjusting - "On the Bench"

Hi Dale, with our head machine, working on one side of the block, we can machine AND install all 8 seats, have them all the same hgts (within a thou or two) by the design of the machine, then without...
Forum: Early V8 (1932-53) 11-18-2019, 02:02 PM
Replies: 19
Views: 510
Posted By GOSFAST
Re: Reinstalling aluminum head questions

Make certain you use washers on the heads, whether you're using bolts or studs, we have "special" washers for this application!

(Add) We use Permatex #1 (hard-setting) on all our builds here,...
Forum: Early V8 (1932-53) 11-18-2019, 08:52 AM
Replies: 40
Views: 1,315
Posted By GOSFAST
Flathead Lifter Adjusting - "On the Bench"

Well almost on the bench anyway? This is for NEW builds only. The method I'll place below here will allow the lifters to be adjusted while out of the unit! It's actually fairly simple and you MAY not...
Forum: Early V8 (1932-53) 11-17-2019, 02:51 PM
Replies: 131
Views: 4,001
Posted By GOSFAST
Re: Spark Plug Protrusion into Head?

"Nailed" that one Jack, probably need a "hundred" or so! Don't have the time to figure the exact number out??

Thanks, Gary in N.Y.

P.S. I would think after 120+ replies and over 3200 views some...
Forum: Early V8 (1932-53) 11-16-2019, 12:02 PM
Replies: 131
Views: 4,001
Posted By GOSFAST
Re: Spark Plug Protrusion into Head?

Anthony, if you can't or won't solve your plug issue with the washers then you'll need "spacers/bushings", these are machined as a 1-piece item. We've done this with a number of customers including a...
Forum: Early V8 (1932-53) 11-14-2019, 02:56 PM
Replies: 131
Views: 4,001
Posted By GOSFAST
Re: Spark Plug Protrusion into Head?

OK, one more time, below here is a shot of heads I have here for another "pending" build, customer still up in the air!

These are a set of Offy "400's", still brand new, circa 1996/1997, these...
Forum: Early V8 (1932-53) 11-08-2019, 08:48 PM
Replies: 22
Views: 1,105
Posted By GOSFAST
Re: flathead rebuild

Sorry guys, missed the end of this post??

We do the bronze-lined guides here, in house! You will never experience another "hung" valve where you install a set. Between the stainless valves we use...
Forum: Early V8 (1932-53) 11-08-2019, 12:19 PM
Replies: 131
Views: 4,001
Posted By GOSFAST
Re: Spark Plug Protrusion into Head?

That plug is the number I used in my drag car (G.M. aluminum heads), it is a reasonably "cold" plug, worked well with the 13:1 C.R.

Here's a "cut & paste" from O'Reilly Auto parts:
...
Forum: Early V8 (1932-53) 11-08-2019, 09:32 AM
Replies: 131
Views: 4,001
Posted By GOSFAST
Re: Spark Plug Protrusion into Head?

Just a heads-up, but to the best of my knowledge and as far back as I can recall all the "N" series Champions were 750" reach.

Believe I ran that series in my 13:1 468" years ago!

Thanks, Gary...
Forum: Early V8 (1932-53) 11-08-2019, 08:21 AM
Replies: 18
Views: 369
Posted By GOSFAST
Re: 8BA Valve length

Hi "J", the lash caps are .080" thick, not sure this will help in Kev's predicament??

Kev, keep in mind you can also work with the valve locks to raise or lower the I.H.'s. Also, I would be...
Forum: Early V8 (1932-53) 11-08-2019, 06:44 AM
Replies: 18
Views: 369
Posted By GOSFAST
Re: 8BA Valve length

Hi Kev, A few years back I fabricated some valve guides that are able to carry up to 5 .060" shims under the springs, the springs sit on "locators" and the shims "stack" between them and the guide,...
Forum: Early V8 (1932-53) 11-07-2019, 08:53 PM
Replies: 131
Views: 4,001
Posted By GOSFAST
Re: Spark Plug Protrusion into Head?

While I agree about not spending a bunch of money on any heads to make things right you really need to keep things in perspective?

Just for arguments sake, if you were to spend as much as $400.00...
Forum: Early V8 (1932-53) 11-07-2019, 05:52 PM
Replies: 18
Views: 369
Posted By GOSFAST
Re: 8BA Valve length

Hi Kev, you may want to figure out what you'll be doing for your installed spring hgts while your mocking that up??

Am assembling 2 units right now, they actually also could have used slightly...
Forum: Early V8 (1932-53) 11-07-2019, 01:27 PM
Replies: 9
Views: 422
Posted By GOSFAST
Re: Clutch chatter....

You really need a "dedicated" Flywheel grinder, this is the sole reason this machine exists, it puts the correct "scalloped" finish on every wheel and compensates for the "hot-spots".

Since a...
Forum: Early V8 (1932-53) 11-07-2019, 12:43 PM
Replies: 131
Views: 4,001
Posted By GOSFAST
Re: Spark Plug Protrusion into Head?

Hi Anthony, set them up now so you won't need any "special" plugs, it may all come back to bite you at a later time?

The most probable way we would end up "fixing" these Offy's we have here on...
Forum: Early V8 (1932-53) 11-06-2019, 08:39 PM
Replies: 131
Views: 4,001
Posted By GOSFAST
Re: Spark Plug Protrusion into Head?

It comes down to the same reason that those "new" Navarro heads we checked out recently got "shot-down", by us anyway, some of the mfr's just don't care! It's sad but true.

With just about any of...
Forum: Early V8 (1932-53) 11-06-2019, 04:24 PM
Replies: 131
Views: 4,001
Posted By GOSFAST
Re: Spark Plug Protrusion into Head?

Hi Dennis, thought I was about to get proved "wrong" here, like I said, it's only really an issue with the Offy heads, believe me!

While we're doing the builds here, not that often with the...
Forum: Early V8 (1932-53) 11-05-2019, 08:17 PM
Replies: 131
Views: 4,001
Posted By GOSFAST
Re: Spark Plug Protrusion into Head?

I can add this tonight, the total thickness of the threads on these particular Offy heads is .570", when you add the spark plug gasket thickness it's another .065", this gives you a grand total of...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:25 AM.