Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: Andy
Forum: Early V8 (1932-53) 01-15-2021, 05:47 PM
Replies: 7
Views: 248
Posted By Andy
Re: 1932 Ford horn needing to make it 12 volt

I ran my 32 Spartan on 12 for many years with no complaint. I screwed the tension down so it would not overspeed. Later I put a beep horn on it.I had found a cheap aftermarket horn somewhere and the...
Forum: Early V8 01-15-2021, 12:42 PM
Replies: 4
Views: 302
Posted By Andy
Forum: Early V8 01-15-2021, 12:40 PM
Replies: 2
Views: 144
Posted By Andy
Re: 32-48 Clamshell set

How about $60 shipped?
Forum: Early V8 01-15-2021, 12:39 PM
Replies: 3
Views: 206
Posted By Andy
Re: 46-48 10in flywheel

I can ship for under $25
Forum: Early V8 01-15-2021, 12:37 PM
Replies: 2
Views: 103
Posted By Andy
Re: F-1 Drag Link

Shipping $15
Forum: Early V8 01-14-2021, 06:58 PM
Replies: 0
Views: 70
Posted By Andy
Speedo 18 Tooth Housing

18 tooth speedo housing for 3.54 gear ratio rear ends. The shaft is there but the gear and cap are missing.
Forum: Early V8 01-14-2021, 05:38 PM
Replies: 0
Views: 68
Posted By Andy
33-36 license Plate Lens

Nice original lens. It has a small chunk out but would not show when installed. Look at pictures. It is not all scrached up. Marked 40-13445.
It is very thick and heavy. I really doubt the repos are...
Forum: Questions & Suggestions 01-13-2021, 10:28 PM
Replies: 3
Views: 155
Posted By Andy
Forum: Early V8 (1932-53) 01-13-2021, 07:56 PM
Replies: 6
Views: 235
Posted By Andy
Re: 1933-34 Speedometer Gear Case

I have an 18 tooth (3.54) case and a shaft. The gears and other parts available I think. $15?
Forum: Early V8 01-11-2021, 04:13 PM
Replies: 3
Views: 206
Posted By Andy
Forum: Early V8 01-11-2021, 04:10 PM
Replies: 4
Views: 302
Posted By Andy
Forum: Early V8 01-11-2021, 04:03 PM
Replies: 1
Views: 187
Posted By Andy
Forum: Early V8 01-11-2021, 03:59 PM
Replies: 1
Views: 92
Posted By Andy
Forum: Early V8 01-11-2021, 03:54 PM
Replies: 2
Views: 103
Posted By Andy
Forum: Early V8 01-11-2021, 03:53 PM
Replies: 2
Views: 144
Posted By Andy
Forum: Early V8 01-08-2021, 05:58 PM
Replies: 1
Views: 92
Posted By Andy
32 Ford Front Hub Grease Retaining Baffle Rings

There are several designs of these small bolt pattern baffles used 32-36. These are original 32.
Fine shape except one has some light rust texturing on the outside bottom of one. Not thin anywhere....
Forum: Early V8 01-08-2021, 05:48 PM
Replies: 2
Views: 103
Posted By Andy
F-1 Drag Link

Really nice F-1 drag link. No rust or damage. One end has the small parts and the other is missing them. The parts kits are available for 15-20. The screw adjusters move as new. All it needs is one...
Forum: Early V8 01-08-2021, 05:35 PM
Replies: 1
Views: 187
Posted By Andy
Cloth Top Tack Strip Sections

These are bits of tack strips for retaining the cloth top inserts in 32-34 Fords. Maybe more years. They are 3/4 in wide, I have had these bits of tack strip forever I kept them as I had never see...
Forum: Early V8 01-08-2021, 05:19 PM
Replies: 2
Views: 144
Posted By Andy
32-48 Clamshell set

A nice set of inner and outer torque tube coupler parts. Never rusted. The inner cup has some minor scoring from debris getting in. No damage to the outer parts. Nothing worn or bent.
Forum: Early V8 (1932-53) 01-02-2021, 11:03 PM
Replies: 5
Views: 264
Posted By Andy
Re: Rebuilding a 36 steering gear

Notice that there is a keyway in the worm/shaft. You must have a driver with a recess to miss the keyway. The worm has the keyway and it fits into the slot in the shaft.
Forum: Early V8 01-02-2021, 04:25 PM
Replies: 0
Views: 104
Posted By Andy
Delete

Delete
Forum: Early V8 01-01-2021, 07:52 PM
Replies: 4
Views: 302
Posted By Andy
Forum: Early V8 (1932-53) 01-01-2021, 02:37 PM
Replies: 12
Views: 570
Posted By Andy
Re: 32 Ford door lock cylinder

You may be looking for 32Phil
Forum: Early V8 (1932-53) 12-31-2020, 07:24 PM
Replies: 11
Views: 787
Posted By Andy
Re: Steering box light switch

You would need the 37-39 bottom plate with the brass tube. Your plate with the steel tube will not let the rod go thru. The rod is .380 or so. They are rolled and not completely round. There is an...
Forum: Early V8 12-31-2020, 04:41 PM
Replies: 0
Views: 129
Posted By Andy
Delete

Delete
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:18 AM.