Forum: Model A (1928-31)
12-10-2019, 10:08 AM
|
|
Replies: 8
Views: 446
Re: Side Mirrors
I opened the hole in the mirror bracket to match the diameter of the door hinge pin, and used a hex head bolt in lieu of the hinge pin. Chrome covers dress-up the bolt head and nut.
Slant window...
|
|
Forum: Model A (1928-31)
12-09-2019, 03:17 PM
|
|
Replies: 7
Views: 317
Re: Edgewater NJ Model "A" Assenbly Line
I note some things in the film:
> All the wheels appear to be black;
> Radiator caps are the standard type - no Quails;
> Body when dropped onto the frame already has pin stripes.
|
|
Forum: Model A (1928-31)
12-09-2019, 02:48 PM
|
|
Replies: 7
Views: 317
Edgewater NJ Model "A" Assenbly Line
https://footage.framepool.com/en/shot/407731974-edgewater-fordism-ford-plant-assembly-line
I stumbled upon this video. My 1931 Coupe was made in this plant. Of special interest to me are:
>...
|
|
Forum: Model A (1928-31)
12-08-2019, 10:25 AM
|
|
Replies: 4
Views: 361
|
|
Forum: Model A (1928-31)
12-08-2019, 10:12 AM
|
|
Replies: 7
Views: 346
Re: Body to frame question
The body blocks & their rubber pads setup the clearance between the running board aprons and body. I strive to get a clearance of 0.25" after shimming the body for alignment.
|
|
Forum: Model A (1928-31)
12-05-2019, 09:05 AM
|
|
Replies: 20
Views: 1,082
|
|
Forum: Model A (1928-31)
12-02-2019, 09:02 AM
|
|
Replies: 7
Views: 479
Re: Wishbone/Trans Connection
Rubber wears rapidly, so it is less durable than the steel parts of the original radius rod ball joint. Given that the radius rod ball is worn, you have choices to restore the joint:
1. Replace the...
|
|
Forum: Model A (1928-31)
12-02-2019, 08:33 AM
|
|
Replies: 22
Views: 883
|
|
Forum: Model A (1928-31)
12-01-2019, 12:09 PM
|
|
Replies: 3
Views: 227
Re: B headgasket
The gaskets are the same except for 2 coolant holes that are in the Model B gasket. The Model A gasket is on the left. You can use the Model B gasket in both the Model A and Model B engines.
|
|
Forum: Model A (1928-31)
11-27-2019, 08:36 AM
|
|
Replies: 41
Views: 995
Re: 12 volt coil with resistor
In 12V electrical systems with breaker point ignitions, ignition coils start the vehicle on 12V through the coil, and the resistor drops the coil to 6V to 8V once the engine is running.
|
|
Forum: Model A (1928-31)
11-26-2019, 12:33 PM
|
|
Replies: 8
Views: 520
Re: Double Venturi Carb using?
The Ford Service Bulletins, Pages 206, 207, 208 & 209 give an excellent description and operation of the Zenith Double Venturi carburetor.
The Secondary Venturi (#10) increases the inlet air...
|
|
Forum: Model A (1928-31)
11-21-2019, 11:57 AM
|
|
Replies: 7
Views: 338
|
|
Forum: Model A (1928-31)
11-21-2019, 11:53 AM
|
|
Replies: 14
Views: 764
Re: #1 plug question
You need to be concerned with the hi-voltage components of the distributor that are the body and the rotor. Modify a distributor cap so you can see what is going on as the rotor passes the #1 contact...
|
|
Forum: Model A (1928-31)
11-20-2019, 12:44 PM
|
|
Replies: 10
Views: 712
Re: Proper crankshaft grinding
Check this article
https://www.enginebuildermag.com/2019/11/cloyes-earns-best-new-product-award-at-aapex-2019/
Watch this Model "A" crankshaft being ground...
|
|
Forum: Model A (1928-31)
11-18-2019, 11:10 AM
|
|
Replies: 2
Views: 264
|
|
Forum: Model A (1928-31)
11-17-2019, 09:54 AM
|
|
Replies: 13
Views: 655
Re: Data plate rivet holes don't line up
I had this problem when restoring my 190A. Rather than rework the original holes in the firewall, I pulled the holes in data plate using a rat tail file. Look closely and you can see the elongation...
|
|
Forum: Model A (1928-31)
11-17-2019, 09:05 AM
|
|
Replies: 6
Views: 398
Re: Oil pressure . . . normal?
The valve chamber is vented to the atmosphere via the crankcase, so once pumped oil reaches the end of the tube in valve chamber, its gauge pressure is zero.
Oil pressure between the oil pump...
|
|
Forum: Model A (1928-31)
11-17-2019, 08:50 AM
|
|
Replies: 5
Views: 327
|
|
Forum: Model A (1928-31)
11-17-2019, 08:43 AM
|
|
Replies: 23
Views: 995
Re: B model distributor question
I do not believe this to be a 1932-1934 Ford distributor.
https://www.fordbarn.com/forum/attachment.php?attachmentid=412880&d=1573963044
|
|
Forum: Model A (1928-31)
11-16-2019, 11:25 AM
|
|
Replies: 2
Views: 238
Re: Bendix Spring bolts
The Bendix starter drives were troublesome throughout the Model "A" years judging by the quantity of service bulletins issued about them. My comments regard the A-11350-C Drive.
Refer to the Ford...
|
|
Forum: Model A (1928-31)
11-16-2019, 11:03 AM
|
|
Replies: 7
Views: 453
|
|
Forum: Model A (1928-31)
11-16-2019, 08:26 AM
|
|
Replies: 23
Views: 995
|
|
Forum: Model A (1928-31)
11-15-2019, 12:19 PM
|
|
Replies: 32
Views: 1,724
Re: Removed engine; some improvements?
Replace & rebuild:
Clutch Disc
Pressure Plate
Throw-Out Bearing
Transmission Pilot Bearing in Flywheel
Front Engine Mount Springs
Rubber Pads on Rear Engine Mounts
All Engine Gaskets...
|
|
Forum: Model A (1928-31)
11-15-2019, 11:39 AM
|
|
Replies: 73
Views: 12,396
|
|
Forum: Model A (1928-31)
11-13-2019, 02:32 PM
|
|
Replies: 13
Views: 864
Re: Modern Shocks any good?
Before giving up on your shocks, try changing the tire pressure. let the tire sidewalls do some of ride damping. Try 32, 30, & 28 psig.
|
