Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: Jim Brierley
Forum: Model A (1928-31) Yesterday, 02:20 PM
Replies: 18
Views: 802
Posted By Jim Brierley
Re: Remove inner oil pan

When you have the dipper tray out and cleaned, hold it up so sunlight will shine on it and check for rusted through spots. Water will settle in the dipper troughs and rust them.
Forum: Model A (1928-31) Yesterday, 12:40 PM
Replies: 3
Views: 230
Posted By Jim Brierley
Re: Rear main oil seal Model B engine

I use the Burtz seal. For the B, 2 full-circle seals are included in the package, the I.D. is the same but different O.D.'s because the cap and upper insert piece are different shapes. Instructions...
Forum: Model A (1928-31) 12-10-2019, 12:34 PM
Replies: 9
Views: 560
Posted By Jim Brierley
Re: Replacing pistons

A rigid hone is best, they tend to straighten the bores. Clean cylinders and below them after honing, otherwise the grit will do serious damage to the engine. Change oil within 100 miles to insure...
Forum: Model A (1928-31) 12-10-2019, 12:27 PM
Replies: 13
Views: 402
Posted By Jim Brierley
Re: Compression test and Vacuum test readings need help

It is undoubtedly valves. You can just force compressed air into the spark plug hole and listen for where the air leaks out, likely into the exhaust pipe.
Forum: Model A (1928-31) 12-09-2019, 12:03 PM
Replies: 49
Views: 6,723
Posted By Jim Brierley
Re: How much better is a B block than an A?

The crank in Brett's engine is a BB, the heavy counterweights were installed by official Ford rebuilders, never from the factory. Reducing bearing diameters takes away some of the rigidity of the B,...
Forum: Model A (1928-31) 12-09-2019, 11:37 AM
Replies: 20
Views: 1,082
Posted By Jim Brierley
Re: High compression head vs cooling

Aluminum does transfer heat more quickly than iron, but the amount of heat generated does not change, so does not affect engine temp. More compression does make the engine more efficient, so more...
Forum: Model A (1928-31) 12-09-2019, 11:26 AM
Replies: 13
Views: 402
Posted By Jim Brierley
Re: Compression test and Vacuum test readings need help

3 and 4 being lower could mean the head gasket is leaking between the two. Try re-torquing the head first, may need a new gasket? A leak-down test would be more conclusive. If that is the problem,...
Forum: Model A (1928-31) 12-09-2019, 11:17 AM
Replies: 11
Views: 560
Posted By Jim Brierley
Re: Whats it worth? 30-31 Briggs fordor

Include pics of all fender. Fordors may be less desirable than other body styles, although wit new wood already installed, it may not make it so?
Forum: Model A (1928-31) 11-15-2019, 12:01 PM
Replies: 32
Views: 1,724
Posted By Jim Brierley
Re: Removed engine; some improvements?

I prefer "stitching" the block rather than welding, and maybe it can be done without removing the engine if the crack is reachable. I just lube the throwout bearing, using a wheel bearing packer to...
Forum: Model A (1928-31) 11-14-2019, 12:18 PM
Replies: 36
Views: 5,305
Posted By Jim Brierley
Re: 4-banger book

Y-block, I don't keep a list but will post here when I have more on hand, probably near the end of the year? Cost has gone to $34 mailed here in the States, first class mail.
Forum: Model A (1928-31) 11-14-2019, 12:12 PM
Replies: 4
Views: 291
Posted By Jim Brierley
Re: 32 B4 rear seal missing

Dan McEarchern, dmcgears@yahoo.com or phone #510-532-8228
Forum: Model A (1928-31) 11-13-2019, 12:24 PM
Replies: 36
Views: 5,305
Posted By Jim Brierley
Re: 4-banger book

I've had several wives buy it for their husbands, for Christmas.

Thanks to all !!!
Forum: Model A (1928-31) 11-13-2019, 12:19 PM
Replies: 19
Views: 1,081
Posted By Jim Brierley
Re: Making an A axle steer easier

I welded mine in 1959, still doing well. Bevel the joint deeply, weld, peen, weld, etc. Peening is important as it relieves stress.
Forum: Model A (1928-31) 11-13-2019, 12:10 PM
Replies: 7
Views: 511
Posted By Jim Brierley
Re: Water Glass

Yes but a stitch repair is better, depending on where the crack is.
Forum: Model A (1928-31) 11-12-2019, 12:06 PM
Replies: 14
Views: 764
Posted By Jim Brierley
Re: 1930 Model A Tudor Value?

Just for comparison, I recently sold my early '30 tudor to a friend. The paint was OK but not as nice as yours, same with interior. It had a fresh touring engine, Ryan overdrive, hydraulic brakes,...
Forum: Model A (1928-31) 11-12-2019, 11:52 AM
Replies: 36
Views: 5,305
Posted By Jim Brierley
Re: 4-banger book

Today's date is 11-12-19, the post is much older but the index posted from fordcragar is current, I had added a chapter on carbs & distributors. I currently have one (1) book in stock but will...
Forum: Model A (1928-31) 11-12-2019, 11:39 AM
Replies: 34
Views: 1,198
Posted By Jim Brierley
Re: Gear ratio

3.54:1 will help, 3.27:1 may be too much for a stock engine?
Forum: Model A (1928-31) 11-12-2019, 11:37 AM
Replies: 19
Views: 1,081
Posted By Jim Brierley
Re: Making an A axle steer easier

Nice looking rig, had hoped to see it in Lincoln last May.

With new king pins and bushings installed and everything lubed, and it still turns hard, shorten the pitman arm. This will give you more...
Forum: Model A (1928-31) 11-11-2019, 12:44 PM
Replies: 2
Views: 358
Posted By Jim Brierley
Re: Camshaft rear bearing oil hole

If it ain't broke, don't fix it!
Forum: Model A (1928-31) 11-11-2019, 12:41 PM
Replies: 6
Views: 531
Posted By Jim Brierley
Re: Low compression

A compression test will probably show where the problem is, leak-down is even better. A squirt of oil in the cylinders will show if it is rings or valves, I'm thinking valves.
Forum: Model A (1928-31) 11-11-2019, 12:37 PM
Replies: 13
Views: 598
Posted By Jim Brierley
Re: Old problem but new twist? Coolant loss

That's too much water loss to be caused by loose head bolts or bad gasket. I had that problem when using a new V8 pump, it was pumping too much and forcing some out the overflow. My solution was...
Forum: Model A (1928-31) 11-11-2019, 12:25 PM
Replies: 15
Views: 737
Posted By Jim Brierley
Re: Werner - ask away

I served in Nurnberg in '61 & '62, and found the German people to be friendly, polite and willing to talk with me, and my German was somewhere between very bad and terrible. You are as welcome here...
Forum: Model A (1928-31) 11-11-2019, 12:16 PM
Replies: 69
Views: 1,895
Posted By Jim Brierley
Re: Veterans Day

Reading all this makes me feel humble and very proud of you all!

I was a draftee, served in Nurnberg, Germany in a 280mm cannon outfit (the "Atomic Cannon"), then 3 months in Benbecula, a very...
Forum: Model A (1928-31) 11-06-2019, 11:28 AM
Replies: 3
Views: 391
Posted By Jim Brierley
Re: model A and B dipper tray

There are differences, but all are interchangeable.
Forum: Model A (1928-31) 11-05-2019, 11:59 AM
Replies: 3
Views: 358
Posted By Jim Brierley
Re: Murrieta Hill Climb

History, I didn't take any pics, haven't been able to post any on this forum anyway, and have tried in the past. A few guys were taking pics, if I can get any I will post on Facebook, where it is...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 11:04 AM.