Go Back   The Ford Barn > Search Forums
Reload this Page Search Results

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 10 of 10
Search took 0.00 seconds. Search: Posts Made By: Tim Warren
Forum: Model A (1928-31) 08-18-2020, 01:19 AM
Replies: 5
Views: 972
Posted By Tim Warren
mounting vase bracket on 31 SW Town Sedan

Can someone tell me if there is a wood in the door post behind the driver's seat. I don't seem to get much of a bite when trying to mount the vase bracket. Thank you in advance.
Forum: Model A (1928-31) 04-10-2019, 10:10 PM
Replies: 21
Views: 3,722
Posted By Tim Warren
Re: Small circuit breaker heats and opens

Got it figured out. I had replaced the rear bulbs w/ halogens. The breaker was a 20 amp OLD guy (just like me!). I replaced the breaker w/ a 30 amp fuse, and problem solved.

Thanks to everyone...
Forum: Model A (1928-31) 03-18-2019, 10:29 PM
Replies: 21
Views: 3,722
Posted By Tim Warren
Small circuit breaker heats and opens

When the engine is NOT running, if I turn my headlights on, they light, and the running lights are on. After a few minutes all go out and the circuit breaker on the small fuse block on the starter...
Forum: Model A (1928-31) 02-25-2019, 11:03 PM
Replies: 1
Views: 987
Posted By Tim Warren
Wiper arm cover for 31 SW Town Sedan

Do all wiper arms have the small stainless cover or are some attached with the clip and spring exposed? Thank you in advance.
Forum: Model A (1928-31) 01-14-2019, 12:08 AM
Replies: 2
Views: 1,274
Posted By Tim Warren
Turn signals: ground or isolate terminal block

I am installing a turn signal in my 31 TS. Can I mount the terminal block that all the wires will feed in to and out of on an inside panel (metal) or does it have to be insulated from grounding? ...
Forum: Model A (1928-31) 12-18-2018, 02:28 AM
Replies: 15
Views: 2,960
Posted By Tim Warren
Re: Flywheel housing-horseshoe engine shims

Thanks everyone for weighing in! Left the shims alone and went to other projects, (carb hook up, alternator, etc. Gave the shims one last try and PRESTO both slipped in. Absolutely no idea what I...
Forum: Model A (1928-31) 12-17-2018, 07:08 PM
Replies: 15
Views: 2,960
Posted By Tim Warren
Re: Flywheel housing-horseshoe engine shims

Gasket in. Just no gap for the shims. Loosen bell housing and jack car at the oil pan to try and recreate a gap, or let it alone?
Forum: Model A (1928-31) 12-17-2018, 04:53 PM
Replies: 15
Views: 2,960
Posted By Tim Warren
Flywheel housing-horseshoe engine shims

I am FINALLY reinstalling my rebuilt engine. Engine in; drivetrain/tanny all in. There is no way to fit the shims that fit at the throttle linkage. The housings are totally mated. Suggestions? Thanks...
Forum: Model A (1928-31) 10-18-2018, 11:52 PM
Replies: 4
Views: 1,318
Posted By Tim Warren
Re: firewall gas supply fitting

Is it a fitting someone makes thaqt I can replace? I have not seen one for sale anywhere.
Forum: Model A (1928-31) 10-16-2018, 11:20 PM
Replies: 4
Views: 1,318
Posted By Tim Warren
firewall gas supply fitting

Can the firewall gas supply fitting (that the shut-off valve screws in to) on a 31 (indented firewall) be removed and replaced w/o removing the gas tank? Thanks in advance for any info.
Showing results 1 to 10 of 10

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:15 PM.