Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 214
Search took 0.01 seconds.
Search: Posts Made By: RandyinUtah
Forum: Model A (1928-31) 01-23-2020, 01:37 AM
Replies: 12
Views: 542
Posted By RandyinUtah
Re: Front Main Spring

I also have a 1959 Triumph TR3 and the original service manual states use the drain oil after each oil change to paint the leaf springs. I don't think the meant using all five quarts.
Forum: Model A (1928-31) 01-19-2020, 02:15 AM
Replies: 27
Views: 1,745
Posted By RandyinUtah
Re: Engine pans

I have had engine pans on my sedan almost 40 years and never had a problem with them breaking. I was lucky and found original ford plans and had them powder coated black.
Forum: Model A (1928-31) 01-13-2020, 01:15 AM
Replies: 5
Views: 650
Posted By RandyinUtah
Re: Front motor mount fixed!

Synchro to stop the squeaking open up the center hole a little bit for clearance and put a little grease around the hole.
The Service manual shows a change in this flat spring.
Forum: Model A (1928-31) 01-12-2020, 01:59 AM
Replies: 39
Views: 1,928
Posted By RandyinUtah
Re: Non-Authentic Paint Colors & Schemes

I feel Edsel changed Henry's mind on this paint colors and more.
Forum: Model A (1928-31) 12-02-2019, 01:32 AM
Replies: 21
Views: 1,472
Posted By RandyinUtah
Re: Heater

Most heaters I have seen require cutting the hole in the firewall.
Forum: Model A (1928-31) 12-02-2019, 01:28 AM
Replies: 16
Views: 1,098
Posted By RandyinUtah
Re: Primer for YOM plates

You should be fine but try and use the same manufacture for the top coat of paint . Read the labels on the can for the correct time between coats.
.
Forum: Model A (1928-31) 12-02-2019, 01:22 AM
Replies: 14
Views: 1,145
Posted By RandyinUtah
Re: air bubbles in rad water.

I have seen small gas bubbles in engines with no head gasket problems. This is caused by local hot spots which boil some of the coolant releasing oxygen molecules.
Forum: Model A (1928-31) 11-24-2019, 11:05 PM
Replies: 18
Views: 921
Posted By RandyinUtah
Re: Model "B" Distributor

I have used the Mallory and model B and returned to the original A.
Forum: Model A (1928-31) 11-11-2019, 12:46 AM
Replies: 51
Views: 2,304
Posted By RandyinUtah
Re: What spark plugs are you currently using?

Same set of 3X for 35 years see no need to change
Forum: Model A (1928-31) 11-11-2019, 12:41 AM
Replies: 38
Views: 1,555
Posted By RandyinUtah
Re: 8 volt battery in 6 volt car

The guy in the video needs to share all his secrets in a new book. How to repair the model A.
Forum: Model A (1928-31) 10-29-2019, 11:56 PM
Replies: 12
Views: 836
Posted By RandyinUtah
Re: Fan replacement

After losing a fan 35 years ago I went with the aluminum fan which came powder coated black and balanced. I would never run a original fan again.
Forum: Model A (1928-31) 10-23-2019, 12:12 AM
Replies: 33
Views: 2,261
Posted By RandyinUtah
Re: Failing gas tank sealant

I think I would forget the pencil filter and build what's called a dirty leg. Do a search on this site to see how it is made and run with it until the flanking stops.
Forum: Model A (1928-31) 10-21-2019, 11:38 PM
Replies: 5
Views: 440
Posted By RandyinUtah
Re: Landaui irons

When I restored my 68B Landau irons I split them apart made a bushing and a new rivet out of stainless steel. After plating I
installed the rivet.
Forum: Model A (1928-31) 10-09-2019, 04:03 PM
Replies: 3
Views: 525
Posted By RandyinUtah
Smile Mafca canyon land tour

370 Model As in the small town of Kanab Re having a great time. People and cars from all over the USA. We have been averaging about 130 miles each day to the three national parks Zion ,Bryce and...
Forum: Model A (1928-31) 08-11-2019, 11:19 PM
Replies: 35
Views: 2,264
Posted By RandyinUtah
Re: not your average coupe

Lots of rain the past two days so I hope it dries up. The rain god's haven't been nice the last couple of years out on the salt.
Forum: Model A (1928-31) 08-08-2019, 07:16 PM
Replies: 11
Views: 888
Posted By RandyinUtah
Re: Getting my creation to go 1.5 to 3 MPH

You might try a model a 4 speed trans with the granny low gear also known a compound low.
Forum: Model A (1928-31) 08-05-2019, 12:01 AM
Replies: 8
Views: 598
Posted By RandyinUtah
Re: 31 slant window outside door handle sag

I agree with what Duke36 has suggested and have fixed many this way. I don't use pliers to make the slight twist I use an 8 inch Cresent wrench.
Forum: Model A (1928-31) 06-09-2019, 01:18 AM
Replies: 34
Views: 2,749
Posted By RandyinUtah
Re: I think my exhaust valves are burnt

Pull the head and the side valve chamber plate and take a look. Not that hard of a job and then your going to know for sure.
Forum: Model A (1928-31) 05-24-2019, 12:04 AM
Replies: 19
Views: 1,481
Posted By RandyinUtah
Re: Fordoor to Tudor

Just compare the rear side window with a fordor
Not even close
.
Forum: Model A (1928-31) 05-21-2019, 11:40 PM
Replies: 24
Views: 1,678
Posted By RandyinUtah
Re: Turn Signal ideas

It's cowl lights with amber lenz for me.
Forum: Model A (1928-31) 05-21-2019, 11:36 PM
Replies: 36
Views: 2,219
Posted By RandyinUtah
Re: What modern points do you use?

I have been running so called modern points for the last 15 years and can't remember the last time I had to change them. No up keep except cam lube.
Forum: Model A (1928-31) 04-05-2019, 12:31 AM
Replies: 18
Views: 1,210
Posted By RandyinUtah
Re: Parts Washer

I have always used stodard solvent in my HF parts washer going on 18 years with no problem with the pump. I do try and clean the filter once in a while.
Forum: Model A (1928-31) 04-02-2019, 01:03 AM
Replies: 4
Views: 643
Posted By RandyinUtah
Re: brake lining counter sink

I purchased one from the wood working section at hardware store
It worked well in my drill press
Forum: Model A (1928-31) 03-31-2019, 06:12 PM
Replies: 4
Views: 763
Posted By RandyinUtah
Re: 1928-1929 Splash Aprons

Steve I don't think every 28 29 splash apron came out of the same stamping press. You know the production numbers ( my guess over 2 million) you my have originals with just round holes. If they...
Forum: Model A (1928-31) 03-31-2019, 06:03 PM
Replies: 13
Views: 966
Posted By RandyinUtah
Re: Production Numbers

The 68B that I restored to a high point Blue Ribbon did not have a body tag or any holes in the flat firewall to attach one. I still have the original patent plate with the engine number stamped on...
Showing results 1 to 25 of 214

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:30 PM.