Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 10 of 10
Search took 0.00 seconds.
Search: Posts Made By: RogerM
Forum: Early V8 (1932-53) 04-10-2019, 03:57 AM
Replies: 11
Views: 1,118
Posted By RogerM
Re: schramm air compressor

Mick
If you dont get any info via the forum, try the Chinchilla Museum in qld
I visited there a few year ago and they had a compressor generator setup
They may have manuals
Web address is...
Forum: Early V8 (1932-53) 09-21-2016, 06:01 AM
Replies: 105
Views: 22,064
Posted By RogerM
Re: Fords in the Fall

Hi
Photo of my 35 ute taken in Canberra (Aust) in Autumn (Fall) earlier this year taken by my son.

Roger
35 ute
Forum: Early V8 (1932-53) 05-10-2016, 05:42 AM
Replies: 10
Views: 1,926
Posted By RogerM
Re: Victoria (Aust) Early Ford V8 Nationals - 2016 - photos

I am glad you are enjoying the photos. They were taken by my son, a keen car photographer. We have the 1935 Roadster Ute (row 4, photo #15 of the Display Edition of the photos). Note the different...
Forum: Early V8 (1932-53) 05-09-2016, 07:30 AM
Replies: 9
Views: 1,756
Posted By RogerM
Re: 40 Helmet distributor shaft movement

If you have a number of different rotors, you will find that they have different lengths due to wear, manufacturing tolerances or supplier differences. Pick the one that gives the appropriate fit -...
Forum: Early V8 (1932-53) 05-09-2016, 05:10 AM
Replies: 10
Views: 1,926
Posted By RogerM
Victoria (Aust) Early Ford V8 Nationals - 2016 - photos

The Early Ford V8 Club of Victoria (Regional Group 151) hosted the Australian Early Ford V8 Nationals in Echuca, on the Murray River, Victoria in April 2016. The links below are to the photos from...
Forum: Early V8 (1932-53) 01-21-2016, 05:25 AM
Replies: 6
Views: 1,732
Posted By RogerM
Re: Dimensioned drawing of flathead V8 engine

Thanks for responses. The “dead stop” method and the two piston method I mentioned are very similar in sensitivity. The latter is best explained by the attached instructions and drawing from the...
Forum: Early V8 (1932-53) 01-20-2016, 06:46 AM
Replies: 6
Views: 1,732
Posted By RogerM
Dimensioned drawing of flathead V8 engine

I have been reviewing all the posts in relation to finding TDC and setting the initial timing – this forum has been a fantastic source of information - thanks.
As well as the various other methods...
Forum: Early V8 (1932-53) 01-06-2016, 04:32 AM
Replies: 11
Views: 2,109
Posted By RogerM
Re: Milesmor Timing Device

For the crab and pre 42 type distributors, the timing plate is held in by a large wire ring type retainer – easily removed with a screw driver. If you don't have an IPB, check out this website below...
Forum: Early V8 (1932-53) 01-05-2016, 05:04 AM
Replies: 11
Views: 2,109
Posted By RogerM
Re: Milesmor Timing Device

There are two types of Milesmor tools, instructions are similar in most (not all) respects. Attached are photos of original pre 42 instructions. Not sure if they are readable.

Just in case, the...
Forum: Early V8 (1932-53) 12-21-2015, 06:41 AM
Replies: 19
Views: 4,182
Posted By RogerM
Re: Dimensioned drawing of flathead engine

I have been reviewing all the posts in relation to finding TDC and setting the initial timing – this forum has been a fantastic source of information.
As well as the various other methods mentioned...
Showing results 1 to 10 of 10

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:44 AM.