Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.06 seconds.
Search: Posts Made By: SSsssteamer
Forum: Model A (1928-31) Today, 09:04 AM
Replies: 9
Views: 493
Posted By SSsssteamer
Re: Les Schwab powder coating

I had five 16" Ford wire wheels done by Les Schwab about 4 months ago out of their Sedro-Woolley, WA store. $35 total for blasting and powder coating. I am elated. Only down side is after...
Forum: Model A (1928-31) 05-26-2020, 11:18 AM
Replies: 9
Views: 384
Posted By SSsssteamer
Re: Rear spring eye

The spring shackle bushing has to be a tight fit in the spring eye for it to wear properly. If your spring is still safe to use, build up the bushing with a little solder for a tighter spring eye...
Forum: Model A (1928-31) 05-25-2020, 01:13 PM
Replies: 6
Views: 390
Posted By SSsssteamer
Re: Radiator comb

The plastic comb would do less damage to the copper cooling fins than would a metal comb. I use the plastic cooling fin comb. I haven't tried a metal one.
Forum: Model A (1928-31) 05-24-2020, 08:04 PM
Replies: 6
Views: 444
Posted By SSsssteamer
Re: Wind Wing Glass - Closed Car

Hi Joop, Yep, I also have 4 closed Model A Fords. I too was also referring to the closed cars. Attached is our 1929 Model A Ford that also has the same type of wind wings. They make a big...
Forum: Model A (1928-31) 05-24-2020, 10:09 AM
Replies: 14
Views: 579
Posted By SSsssteamer
Re: Steering turn from center

The steering arm on the front spindle could be bent. It would be the easiest one to bend to correct the unequaled steering problem. A little heat, a little tweak and you are done.
Forum: Model A (1928-31) 05-23-2020, 11:19 PM
Replies: 6
Views: 444
Posted By SSsssteamer
Re: Wind Wing Glass - Closed Car

Once the glass is captured between the wind wing brackets, there is no way for it to fall out. I have had mind on my '29 Tudor for 52 years now with out any problems. I wouldn't leave home without...
Forum: Model A (1928-31) 05-22-2020, 11:18 PM
Replies: 9
Views: 464
Posted By SSsssteamer
Re: Attempt to remove body bolts, or just cut them off?

I have been able to break most of the body bolts off using vice grips on one side and a good fitting wrench on the other side. I have also used a cold chisel to split the nuts. So far I have not...
Forum: Model A (1928-31) 05-11-2020, 11:14 PM
Replies: 10
Views: 685
Posted By SSsssteamer
Re: Soldering and Nickel Plating

I have been this route. My plater "Specialized Plating" in Mt. Vernon, WA will not plate over lead solder repairs. He will plate over Silver solder repairs, and about any other metal. He does...
Forum: Model A (1928-31) 05-10-2020, 10:33 AM
Replies: 19
Views: 1,116
Posted By SSsssteamer
Re: 3.27 Ring and Pinion

The jump between 2nd and 3rd with 3.27 gears isn't much different than with the 3.53 or the 3.78 gears. There is only a small additional power gap between those gears, but with the 3.27 gears, you...
Forum: Model A (1928-31) 05-08-2020, 11:14 PM
Replies: 19
Views: 1,116
Posted By SSsssteamer
Re: 3.27 Ring and Pinion

I put a 3.27 rear end gears in my 1931 CCPU. It was a very smart move and the pickup pulls it easily. I put a 3.54 in my 1929 Tudor and it pulls 4 people nicely. Would a 3.27 in my Tudor have been...
Forum: Model A (1928-31) 05-01-2020, 07:54 PM
Replies: 6
Views: 388
Posted By SSsssteamer
Re: Estimatet mileage since 5/1928

My 1929 Tudor I bought from the original owner in 1968. The owner lived on an island and the A only had 52,000 original miles on it. In the last 52 years I have added another 52,000 mile to its...
Forum: Model A (1928-31) 04-27-2020, 12:19 AM
Replies: 15
Views: 1,343
Posted By SSsssteamer
Re: how bad is this cluster gear? photos.

The hard facing is worn away from the gears and that is just where the teeth will snap off, on their pitted dotted lines. Don't waste the labor using those bad gears again. Do it right the first...
Forum: Model A (1928-31) 04-26-2020, 06:10 PM
Replies: 345
Views: 31,986
Posted By SSsssteamer
Re: Just wondering : what's your year of birth ?

April, 1945. Been driving our 1929 tudor for 52 years now. Raised our family of five with it. I'm 75 years old this month.
Forum: Model A (1928-31) 04-24-2020, 07:23 PM
Replies: 28
Views: 1,449
Posted By SSsssteamer
Re: Good time to check your fan blades

I lost a fan blade in '68 also. I will never forget it. It not only ruined my radiator, but the out of balance fan also tore the water pump off of the block too. Sounded like a shot gun going off...
Forum: Model A (1928-31) 04-20-2020, 10:18 PM
Replies: 9
Views: 640
Posted By SSsssteamer
Re: Early 30 Pickup Floorboard Quandry

I experienced this similar problem with my '36 Ford pickup. I went underneath the truck and drilled a pilot hole up through all of the holes that could be reached from below. The ones that were...
Forum: Model A (1928-31) 04-18-2020, 09:30 AM
Replies: 12
Views: 477
Posted By SSsssteamer
Forum: Early V8 (1932-53) 04-04-2020, 10:04 AM
Replies: 6
Views: 341
Posted By SSsssteamer
Re: 1936 Pick up tail gate rivets

G.M., If I was to use the Fillister head screws for the tail gate hinges, I would have to have their nuts located on the inside of the tailgate. While loading goods, the nuts would create damage to...
Forum: Early V8 (1932-53) 04-03-2020, 02:45 PM
Replies: 6
Views: 341
Posted By SSsssteamer
Re: 1936 Pick up tail gate rivets

Nels, I have the round headed rivets in stock. I can use them, but they sure do stand proud. Thanks for the advice on the painted Ford Script. I didn't know that.
Forum: Early V8 (1932-53) 04-03-2020, 09:45 AM
Replies: 6
Views: 341
Posted By SSsssteamer
1936 Pick up tail gate rivets

On the 1936 Ford pick up tail gate rivets, what type of rivet head did Ford use for the rivet heads? Domed rivet head, pan head, nail head or ? I especially have to get the tailgate hinge rivet...
Forum: Model A (1928-31) 04-03-2020, 09:33 AM
Replies: 28
Views: 1,573
Posted By SSsssteamer
Re: Cracked head- pic

Ditto. Potential problems from the cracks.
Forum: Model A (1928-31) 03-29-2020, 11:24 AM
Replies: 19
Views: 1,215
Posted By SSsssteamer
Re: Stipe shocks...

I put the Stipes shock on my '31 A pickup. Handles a world better than without.
Forum: Model A (1928-31) 03-25-2020, 11:14 PM
Replies: 4
Views: 277
Posted By SSsssteamer
Re: 29 Tudor interior door panel question

The cut corner is necessary for the front corner to fit under the garnish molding and also the doors are trimmed back there also to give the dash panel some room to clear the doors. Today I was...
Forum: Early V8 (1932-53) 03-23-2020, 12:32 PM
Replies: 20
Views: 823
Posted By SSsssteamer
Re: Seat springs: paint or no?

I have always painted my seat springs with black Rustolium rust preventative spray paint. Once a seat spring starts to rust, eventually it can break at that rusted area. Paint the seat springs. ...
Forum: Model A (1928-31) 03-23-2020, 12:20 PM
Replies: 46
Views: 3,118
Posted By SSsssteamer
Re: Coronavirus vs "A" Drive

LOL... Sounds just like me. I was told 20 months ago that I had only 6 or 8 months left to live, because I am going to die from my cancer.
I still have a couple of cars to finish before I am...
Forum: Model A (1928-31) 03-11-2020, 10:32 AM
Replies: 10
Views: 418
Posted By SSsssteamer
Re: What's your favourite Model T/A era car accessory brand?

Since we drive our Model A year round in the Northwest, My wife's favorite Model A accessory brand is the Auto-lite heater manifold. Delightful in cold weather.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 04:49 PM.