Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.08 seconds.
Search: Posts Made By: FL&WVMIKE
Forum: Early V8 (1932-53) 07-04-2020, 12:24 PM
Replies: 11
Views: 618
Posted By FL&WVMIKE
Re: Hard seats on exhaust only

Hardened seats are only used on the exhaust... That being said, the only vehicles that NEED hardened seats, are those that are run under heavy load and see a lot of miles. An occasional use...
Forum: Early V8 (1932-53) 06-18-2020, 02:11 PM
Replies: 40
Views: 12,559
Posted By FL&WVMIKE
Re: Transmission oil

As was said, I've been driving and rebuilding Ford Toploaders (the cast iron ones made from 1964-to 1973-ish) for 30 years.

The places that specialize in Toploader rebuild parts/rebuild kits...
Forum: Early V8 (1932-53) 06-18-2020, 09:33 AM
Replies: 40
Views: 12,559
Posted By FL&WVMIKE
Re: Transmission oil

GL-5 is supposed to be harder on bronze/yellow metals. GL-4 is supposed to be safe. GL-1 does not have the extreme pressure additives, and does not protect as well as the more modern oils.
...
Forum: Early V8 (1932-53) 06-15-2020, 09:11 AM
Replies: 19
Views: 994
Posted By FL&WVMIKE
Re: Flushing engine block

I ran a Gano Filter (screen filter for the cooling system) on the mustang back in the day, and do not recommend them. They are okay if you check and empty them constantly, but about all they did for...
Forum: Early V8 (1932-53) 06-15-2020, 08:12 AM
Replies: 19
Views: 994
Posted By FL&WVMIKE
Re: Flushing engine block

Dad and I attacked a torn down 21 stud with a 9 hp Pressure Washer and a long Screwdriver. The amount of sediment in the bottom rear was shocking. You could tell much of that had been there for...
Forum: Early V8 (1932-53) 06-07-2020, 09:34 AM
Replies: 31
Views: 1,264
Posted By FL&WVMIKE
Re: Women buy shoes: Guys buy toys[old Fords]

The picture of the flamed street rod above reminded me of this one owned by Bob Sayre in WV. I believe this picture was taken in 1991... or maybe very late 1980's. Not sure. Anyway, this was at...
Forum: Early V8 (1932-53) 06-03-2020, 08:57 AM
Replies: 31
Views: 1,264
Posted By FL&WVMIKE
Re: Women buy shoes: Guys buy toys[old Fords]

This car has FAR more class than a 350 SBC with a 350 Turbo Automatic trans in a generic street rod! It's actually 'period correct', and the ONLY thing that looks like it has been changed is the...
Forum: Early V8 (1932-53) 06-01-2020, 08:08 PM
Replies: 20
Views: 1,083
Posted By FL&WVMIKE
Re: Wheel bearing grease

If you watch those Project Farm Youtube Videos that were posted, you'll see:
Lucas 'Red and Tacky'
Walmart Grease
High grade Marine Grease
Grease from the 1940's.

They found all grease is NOT...
Forum: Early V8 (1932-53) 05-31-2020, 11:29 AM
Replies: 16
Views: 713
Posted By FL&WVMIKE
Re: Newly assembled Flatty cranking force??

An assembled V8 engine should not take excessive force to turn over with the spark plugs removed. If it is HARD to turn over, look for the reason. As Ron said, seals and rings are the main culprit...
Forum: Early V8 (1932-53) 05-30-2020, 11:48 PM
Replies: 20
Views: 1,083
Posted By FL&WVMIKE
Re: Wheel bearing grease

Yea, he's awesome! Here is a test of where he compared a vintage grease from the 1940's to a modern grease.

https://www.youtube.com/watch?v=l7hpDm8lTME&list=PLjT3B9r2z3fVdu2Ht5z_Qpe2dkKi2vRG6
...
Forum: Early V8 (1932-53) 05-30-2020, 05:52 PM
Replies: 20
Views: 1,083
Posted By FL&WVMIKE
Re: Wheel bearing grease

Grease Test by Project Farm.
All greases are NOT the same. Very interesting to see how they compare.

https://www.youtube.com/watch?v=mMmSQSjraSE&t
Forum: Early V8 (1932-53) 05-29-2020, 03:43 PM
Replies: 39
Views: 1,852
Posted By FL&WVMIKE
Re: Would You Use it?

Yes. The reduction in compression ratio would be drastic. Using two gaskets on a OHV sized combustion chamber (simple circle) adds a lot of space. Doing it on a flathead sized combustion chamber...
Forum: Early V8 (1932-53) 05-27-2020, 11:08 PM
Replies: 39
Views: 1,852
Posted By FL&WVMIKE
Re: Would You Use it?

Regarding the use of two different gaskets on the same engine... The gasket needs something SOLID on both sides, or it will not seal. Running circles and trapezoids together will NOT seal. Plus,...
Forum: Early V8 (1932-53) 05-27-2020, 05:48 PM
Replies: 46
Views: 2,288
Posted By FL&WVMIKE
Re: Eagle 4" 8BA Crank?

Airflow is what dictates maximum potential horsepower. You could bore/stroke a flathead out to 500ci, and it wouldn't turn over 1200 rpm before it was maxed out in the breathing department. Only...
Forum: Early V8 (1932-53) 05-26-2020, 04:30 PM
Replies: 46
Views: 2,288
Posted By FL&WVMIKE
Re: Eagle 4" 8BA Crank?

These Chinese sourced cranks are used extensively in small/big block Fords, Chevys, Dodges, etc. The come in cast as well as Forged alloys. They, as well as the connecting rods have proven...
Forum: Early V8 (1932-53) 05-20-2020, 11:29 AM
Replies: 22
Views: 1,388
Posted By FL&WVMIKE
Re: King pin removal, the hard way!

Yea, they have tool like this to work with. Very simple, and highly effective!
https://www.youtube.com/watch?v=cvR12q9yclE
Forum: Early V8 (1932-53) 05-20-2020, 11:22 AM
Replies: 11
Views: 1,096
Posted By FL&WVMIKE
Re: Summit racing

I ALWAYS recommend a return line when using electric fuel pumps. They work much better, last longer and run cooler when they can circulate the fuel. They are not usually happy when 'dead headed'...
Forum: Early V8 (1932-53) 05-09-2020, 06:01 PM
Replies: 20
Views: 1,317
Posted By FL&WVMIKE
Re: Painting with Acrylic Enamel question

Not 100% related, but I was talking to a buddy of mine who paints cars, and he said a good budget paint is oil based Rustoleum enamel at Tractor Supply. He said the secret is to add hardener. Once...
Forum: Early V8 (1932-53) 05-09-2020, 11:29 AM
Replies: 34
Views: 1,548
Posted By FL&WVMIKE
Re: Of 34 Phaetons - woodticks - n - Brook Trout

Truly happy to see David using and enjoying this car as it was intended! It's a very, very solid car that has never been abused, neglected or rotten. It's the perfect DRIVER.

David's stories...
Forum: Early V8 (1932-53) 03-12-2020, 12:13 PM
Replies: 37
Views: 5,021
Posted By FL&WVMIKE
Re: Torque plate blueprint, or possibly rent one?

It is also IMPERATIVE to use the same gasket with the torque plate that you'll be using on the engine. Using the gasket makes a big difference... especially with heads that have a fire ring around...
Forum: Early V8 (1932-53) 01-22-2020, 06:04 PM
Replies: 11
Views: 736
Posted By FL&WVMIKE
Re: Cranking Capacity

The only decent 6V battery out there seems to be the Optima. All the rest seem like they are stuck in the 50's. No other 'modern' designed 6V batteries that I know of... and none of those that I...
Forum: Early V8 (1932-53) 01-20-2020, 01:20 PM
Replies: 21
Views: 1,684
Posted By FL&WVMIKE
Re: LED shop light follow-up

If you already have 8ft fluorescent bulbs, the Retro-fit LED's are a killer upgrade. They bypass the ballast, but it's EASY to wire!

There is a white wire and a black wire coming in from...
Forum: Early V8 (1932-53) 01-20-2020, 09:38 AM
Replies: 24
Views: 1,516
Posted By FL&WVMIKE
Re: What Electric Pump do you recommend?

I'm assuming there is also a filter before the carburetor. The filter before the electric pump is to protect the pump from rust/debris from the tank that could lock it up.

I like the the above...
Forum: Early V8 (1932-53) 01-19-2020, 11:44 PM
Replies: 24
Views: 1,516
Posted By FL&WVMIKE
Re: What Electric Pump do you recommend?

If a person does not want to rely on an electric pump, but wants to have one in case their mechanical one goes out, or use it to prime the carb, supplement the old mechanical unit, etc... a check...
Forum: Early V8 (1932-53) 01-07-2020, 11:55 AM
Replies: 16
Views: 1,408
Posted By FL&WVMIKE
Re: Optima 6V battery charge

I've had the best luck NOT keeping these batteries on the trickle charger (Battery Tender) 100% of the time. I'll put the charger on for a day or so once every month or so, but leave it at that. I...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:11 AM.