Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.07 seconds.
Search: Posts Made By: Lawrie
Forum: Early V8 (1932-53) 07-03-2020, 05:25 PM
Replies: 5
Views: 265
Posted By Lawrie
Re: 1934 Gearbox Parts

Bearings ,(the front and rear) are easy to get from you local bearing supplier, Just don't use Ch**** ones,
Lawrie
Forum: Early V8 (1932-53) 07-02-2020, 03:56 PM
Replies: 24
Views: 1,160
Posted By Lawrie
Re: Latest bubba report

Jim, great to see you back ,
Seeing that T in your shed makes me think I should get the one from the farm wife and I visited last week.
Take care and stay well.
Lawrie
Forum: Early V8 (1932-53) 07-01-2020, 05:17 PM
Replies: 33
Views: 894
Posted By Lawrie
Re: 1934 Tudor needs a little hop-up

There was a 3.54 for sale in the swap section.
Lawrie
Forum: Early V8 (1932-53) 06-30-2020, 05:58 PM
Replies: 33
Views: 894
Posted By Lawrie
Re: 1934 Tudor needs a little hop-up

Vincent, you can do it a cheaper way for the rear end ratio change,
What I did was to get a set of later model (48) 3.78 gearset and machine them to fit the 33/34 rear end.
If you have access to a...
Forum: Early V8 (1932-53) 06-26-2020, 04:19 PM
Replies: 19
Views: 911
Posted By Lawrie
Re: Cornhead grease in steering

Make up a 1/4 tube to screw onto your grease gun ,insert into through the filler hole and down in the box and fill the box from the bottom.
Lawrie
Forum: Early V8 (1932-53) 06-26-2020, 04:59 AM
Replies: 6
Views: 371
Posted By Lawrie
Re: Helmet distro gaskets

Fixed it ,left out the NO.
Lawrie
Forum: Early V8 (1932-53) 06-26-2020, 04:57 AM
Replies: 35
Views: 1,728
Posted By Lawrie
Re: Old Henry

Trevor, you should get him to stop in QLD on his way to or from H/kong,
Lawrie
Forum: Early V8 (1932-53) 06-25-2020, 08:53 PM
Replies: 54
Views: 1,938
Posted By Lawrie
Re: best way to adjust valves

I do mine by turning engine until the valve is fully open, then turn one complete revolution adjust that valve, do the others ,sure it takes a while longer but it means every valve is on the heal of...
Forum: Early V8 (1932-53) 06-25-2020, 05:13 PM
Replies: 19
Views: 1,132
Posted By Lawrie
Re: NOS parts

Maybe we on the barn could all put in a few bucks to allow Michael to purchase these parts.
worth a thought.
Lawrie
Forum: Early V8 (1932-53) 06-24-2020, 08:33 PM
Replies: 24
Views: 785
Posted By Lawrie
Re: 34 Issues Ongoing -Video

Have you changed out the distributor for another even its not the 40b,
try another coil and condenser,also hot wire it from the coil terminal direct to the battery ,only run it for a short time as...
Forum: Early V8 (1932-53) 06-24-2020, 04:02 PM
Replies: 6
Views: 371
Posted By Lawrie
Re: Helmet distro gaskets

I ran our 33 for 30 miles in the worst rain ever last week ,it never missed a beat, I bet it would have with no gaskets in the distributor.
When we first had the 33 it had a remote coil setup, and...
Forum: Early V8 (1932-53) 06-24-2020, 01:44 AM
Replies: 21
Views: 679
Posted By Lawrie
Re: Classic condenser failure?

Thanks ,seeing as I'm down under I was reading them upside down.Lol
Lawrie
Forum: Early V8 (1932-53) 06-23-2020, 04:31 PM
Replies: 63
Views: 2,232
Posted By Lawrie
Re: lowest oil pressure for engine to survive

GM, you are right about the oil temp, for a long time I hade one on the 33,it would get to over 100deg C on long uphill pulls , ran around 75-80C on the flat in summer here.
Lawrie
Forum: Early V8 (1932-53) 06-23-2020, 04:25 PM
Replies: 21
Views: 679
Posted By Lawrie
Re: Classic condenser failure?

Micheal, is there a code in those letters,
Cam followers you sent are fitted , thanks
Lawrie
Forum: Early V8 (1932-53) 06-19-2020, 12:41 AM
Replies: 4
Views: 209
Posted By Lawrie
Re: Generator rebuild parts

I used NOS one in our 33,BUT they would throw a wire out of the commutator sometimes ,( Our 33 does lots of miles), the best fix was to get the armatures rewound, no problem since.
Lawrie
Forum: Early V8 (1932-53) 06-18-2020, 05:17 PM
Replies: 18
Views: 627
Posted By Lawrie
Re: U-Joint Terminology

Coopman, its easy to get the u/j centre,I sat the U/J trans end down on a flat surface, then measured down from the top of the U/J cross bearing or the actual shaft, down to the flat surface, deduct...
Forum: Early V8 (1932-53) 06-18-2020, 05:03 PM
Replies: 10
Views: 609
Posted By Lawrie
Re: high compression cylinder heads

Ron, I always use a stock cam,And I think I have a good ign system in the helmet distributor with the 11a advance fitted and 6v.
Seems reliable enough and I think goes OK.
Lawrie
Forum: Early V8 (1932-53) 06-18-2020, 02:18 AM
Replies: 10
Views: 609
Posted By Lawrie
Re: high compression cylinder heads

Ron. I will keep you posted on how it goes.
It will be going in the 33 to tow the caravan.
It will be another month or so though.
Lawrie
Forum: Early V8 (1932-53) 06-17-2020, 05:24 PM
Replies: 37
Views: 1,594
Posted By Lawrie
Re: Nice country drive

Tinker, yes always towing the c/van.
Danny,
2 in inlet and 1-3/4 outlet, but the so called muffler is only 4 inches round and 14 long.Plus I had sleaved the front pipe down to 1-3/4 with an...
Forum: Early V8 (1932-53) 06-17-2020, 05:17 PM
Replies: 18
Views: 627
Posted By Lawrie
Re: U-Joint Terminology

I'm sure that as you have gone to all the trouble of making up that neat conversion you will know that the centre of the pivot point on the U/J needs to be in exactly the same plane as the pivot...
Forum: Early V8 (1932-53) 06-17-2020, 04:12 PM
Replies: 10
Views: 609
Posted By Lawrie
Re: high compression cylinder heads

I'm going to try a set of the Edelbrock 65 cc heads on my spare engine,99a block 4 in stroke and 3-5/16 bore,I also have one of the BIG 97,stro try on it.
Lawrie
Forum: Early V8 (1932-53) 06-17-2020, 01:46 AM
Replies: 18
Views: 627
Posted By Lawrie
Re: U-Joint Terminology

I don't know the answer, but if you look on the strange engineering website they have a pile of that sort of stuff there.
Lawrie
Forum: Early V8 (1932-53) 06-16-2020, 01:24 AM
Replies: 37
Views: 1,594
Posted By Lawrie
Re: Nice country drive

Home this arvo,
only 660 miles ,
car went well ,no leaks in the pouring rain .
Last drive was from Monto to home (Gladstone) and the big hill, and logging trucks, we waited at the top of the hill...
Forum: Early V8 (1932-53) 06-14-2020, 04:52 PM
Replies: 40
Views: 12,462
Posted By Lawrie
Re: Transmission oil

Rudolf,thanks for that useful info on what temp the later gl5 oil will attack the bronze parts,
I reverted to using GL5 oil in my trans as we have trouble getting the gl4,
My trans do a lot of...
Forum: Early V8 (1932-53) 06-14-2020, 12:18 AM
Replies: 7
Views: 228
Posted By Lawrie
Re: '38 u-joint belleville washer

I don’t think that there is a Bellville washer in there!just a heavy flat washer some times with a dimple to line up with a spline on the u/joint.use a heavy duty spring washer and torque 30 ft lbs...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:50 AM.