Forum: Model A (1928-31)
02-23-2024, 11:00 PM
|
Replies: 17
Views: 714
|
Forum: Model A (1928-31)
02-22-2024, 11:47 AM
|
Replies: 9
Views: 614
Re: Metal Stem Tire Valve question
Just to clarify, I believe Mr. Karr in post 6 is referring to vulcanized metal stems already installed in vendors' tubes, not vulcanized rubber stems with dust covers ?
|
Forum: Model A (1928-31)
02-22-2024, 11:37 AM
|
Replies: 10
Views: 620
|
Forum: Model A (1928-31)
02-05-2024, 10:48 PM
|
Replies: 7
Views: 831
Re: 8 leaf to 7 leaf rear spring conversion
Putting aside the thicknesses, why not use the shortest #10 leaf as the dummy and bevel the top edges of the #8 leaf to become the top of the 7 leaf spring ? Or use the #8 longer leaf as the dummy...
|
Forum: Model A (1928-31)
01-01-2024, 05:51 PM
|
Replies: 2
Views: 393
Re: bottom door seal direction, '31 PU
nub faces towards cabin, ; i.e., the upholstery panel bottom edge sits on the nub or bulb part on the closed cab which gets compressed against the metal body sill..
|
Forum: Model A (1928-31)
10-28-2023, 11:00 AM
|
Replies: 50
Views: 6,110
|
Forum: Model A (1928-31)
10-26-2023, 01:08 PM
|
Replies: 50
Views: 6,110
Re: Thermostat
There have been internet discussions about installing thermostats without a by pass system used in engines designed for a stat. The rear cylinder on an A may get too hot with potential steam pockets...
|
Forum: Model A (1928-31)
09-05-2023, 10:16 AM
|
Replies: 11
Views: 1,070
|
Forum: Model A (1928-31)
06-19-2023, 03:39 PM
|
Replies: 19
Views: 3,152
Re: "Modern" Shocks from Snyders
Check out Pete and Jakes "plain hydraulics"; they may be similar to the A vendors offerings and have similar rebound rates. The 60's VW Empi shocks with eyelets fit the Snyders kit (with mod's to...
|
Forum: Model A (1928-31)
06-17-2023, 10:17 AM
|
Replies: 19
Views: 3,152
Re: "Modern" Shocks from Snyders
Yes, but by experience, some gas charged tube shocks can be too stiff for an A.
Angling them can help the spring rates (see attached) and lessen the firmness.
|
Forum: Model A (1928-31)
06-15-2023, 03:18 PM
|
Replies: 43
Views: 5,280
|
Forum: Model A (1928-31)
05-24-2023, 01:42 PM
|
Replies: 29
Views: 3,034
Re: Dang, Grease on the Headliner
This is difficult to address today because most dry cleaning fluids have been banned.
Don't use Folex or any water based cleaner which can bleed out (leave rings) if on natural fabrics. If...
|
Forum: Model A (1928-31)
05-10-2023, 10:32 AM
|
Replies: 64
Views: 9,391
|
Forum: Model A (1928-31)
05-02-2023, 01:11 PM
|
Replies: 18
Views: 3,627
Re: Gaskets 101, advice?
[QUOTE=Bob Bidonde;1669333]
The exhaust manifold gasket must be metal to withstand exhaust gas temperatures. Also, the gland rings protect the gasket from burning. Be sure each gland ring, when...
|
Forum: Model A (1928-31)
04-30-2023, 11:36 AM
|
Replies: 125
Views: 22,725
Re: MMO in the Gas
Some use ZDDP zinc additive for flat tappet motors since zinc is banned from fuels due to catalytic convertor issues with zinc. If there is test data for all these additives, it would be good to see...
|
Forum: Model A (1928-31)
04-30-2023, 11:28 AM
|
Replies: 20
Views: 2,765
Re: wheel lug nuts
Some suggest not to use the washers if not needed due to nuts loosening though never had any experience with them.
|
Forum: Model A (1928-31)
04-30-2023, 11:26 AM
|
Replies: 16
Views: 2,068
Re: Fuel tank strainer,screen?
There are screw in and drop in types. Ford initially used the screw in type, then drop in with tabs, and then in '31 went back to the screw in type. One can adapt the drop in type for the later style...
|
Forum: Model A (1928-31)
04-30-2023, 11:19 AM
|
Replies: 20
Views: 2,765
Re: wheel lug nuts
On going issue, and with some repro nuts, the throats may not be deep enough or the threads cut properly.
|
Forum: Model A (1928-31)
04-30-2023, 11:15 AM
|
Replies: 18
Views: 3,627
Re: Gaskets 101, advice?
This is an older post, but I think Mr. Bidonde is referring to the tailpipe end which is allowed to slide thru the frame clamp. (Not a reference to the manifold to muffler up pipe that is clamped...
|
Forum: Model A (1928-31)
04-24-2023, 11:44 PM
|
Replies: 9
Views: 1,523
|
Forum: Model A (1928-31)
03-25-2023, 09:23 AM
|
Replies: 2
Views: 670
Aluminum Fan installation
Should a washer be used under the castle nut when installing the repro aluminum fan ? Nothing in the instructions about a washer.
|
Forum: Model A (1928-31)
03-19-2023, 11:41 AM
|
Replies: 4
Views: 948
Re: Spotted Upholstery
Depending on stain on natural fabrics such as the brown cottons or mohair, if you can find some Naptha, or dry cleaning fluid, blot with that on a hidden test area 1st. Water based cleaners may leave...
|
Forum: Model A (1928-31)
03-19-2023, 11:29 AM
|
Replies: 33
Views: 5,884
Re: Rear axle nut
How does the cotter key go on the axle steeped nut ? Should the legs be crimped over the axle end or in to the steps?
|
Forum: Model A (1928-31)
03-14-2023, 10:19 AM
|
Replies: 48
Views: 7,912
Re: European classic tyres
Lucas ,made in Vietnam, and the Excelsior tires are Nylon cord, not polyester.
Try Coker or Jegs, the latter has a discount offer for Excelsior. The Euro's are headquartered near Copenhagen, De. but...
|
Forum: Model A (1928-31)
03-12-2023, 11:21 AM
|
Replies: 31
Views: 4,679
|