Forum: Early V8
04-28-2019, 05:03 PM
|
|
Replies: 0
Views: 878
|
|
Forum: Early V8 (1932-53)
03-07-2018, 09:34 PM
|
|
Replies: 30
Views: 6,431
Re: Would you try to save this?
I also had to tig weld with Ni rod some of the intake port so there would be enough material there to seal. Also relieved and drilled the lifter bores. This engine will be getting a 4.250" stroke...
|
|
Forum: Early V8 (1932-53)
03-07-2018, 09:24 PM
|
|
Replies: 30
Views: 6,431
Re: Would you try to save this?
Just following up on my initial post, didn't realize it had been almost 4 years since I tore this engine down! I did decide to save this block and just got it back from the machine shop today. I...
|
|
Forum: Model-T
07-19-2017, 06:43 AM
|
|
Replies: 1
Views: 1,807
|
|
Forum: Model-A
01-22-2017, 07:03 PM
|
|
Replies: 0
Views: 1,215
|
|
Forum: Model-A
01-22-2017, 07:00 PM
|
|
Replies: 0
Views: 1,152
|
|
Forum: Model-A
01-22-2017, 06:58 PM
|
|
Replies: 0
Views: 1,017
Curved inner panel
28-31 roadster / 30-31 coupe with rumble seat curved inner panel, appears to be NOS - SOLD
|
|
Forum: Model-A
01-22-2017, 06:55 PM
|
|
Replies: 0
Views: 889
|
|
Forum: Model-A
01-22-2017, 06:52 PM
|
|
Replies: 0
Views: 909
|
|
Forum: Model-T
01-22-2017, 06:49 PM
|
|
Replies: 1
Views: 1,807
26-27 Model T headtlights
26-27 Ford Model T headlights, brass reflectors, brass rims, has been converted to modern 12V H3 bulbs $200obo
|
|
Forum: Early V8
01-22-2017, 06:47 PM
|
|
Replies: 0
Views: 767
|
|
Forum: Early V8 (1932-53)
05-29-2014, 07:21 AM
|
|
Replies: 30
Views: 6,431
Re: Would you try to save this?
This is the worst cylinder. I don't have them all cleaned up but upon initial inspection the others look ok. Someone had left the sparkplugs out of this engine and it must have sit with water in the...
|
|
Forum: Early V8 (1932-53)
05-28-2014, 08:15 PM
|
|
Replies: 30
Views: 6,431
Would you try to save this?
This cylinder has a lot of pitting around the intake valve over to the cylinder. I can put a new seat in it and deck the block slightly but I am worried about this causing detonation or being a...
|
|
Forum: Model A (1928-31)
06-17-2012, 06:29 AM
|
|
Replies: 5
Views: 2,118
Re: Measuring Pistons
The skirt actually has a slight barrel shape ) to it from top to bottom. The piston should be measured 90deg to the pin and usually 1/2" up from the bottom of the skirt (this measuring point can vary...
|
|
Forum: Model-A
11-09-2011, 12:56 PM
|
|
Replies: 12
Views: 2,857
|
