Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.08 seconds.
Search: Posts Made By: Kurt in NJ
Forum: Model A (1928-31) Yesterday, 02:45 PM
Replies: 9
Views: 449
Posted By Kurt in NJ
Re: Coil Testing With Multi-Meter

With resistance measurements you can condemn a totally bad (open winding), but you can't confirm it's good--- but you need a more dynamic test-- and a hot coil , many will check ok by resistance, and...
Forum: Model A (1928-31) 02-16-2020, 03:43 PM
Replies: 9
Views: 477
Posted By Kurt in NJ
Re: The Diamond Mark Challenge

what i see is a original A block has a X reinforcement under the stud in the center, diamond blocks have none ---most diamond blocks have exhaust seat inserts
Forum: Model A (1928-31) 02-15-2020, 08:01 PM
Replies: 7
Views: 430
Posted By Kurt in NJ
Re: Head Torque

I torqued mine over a 3 days of driving, haven't touched it since--- ---35 years ago-- using the tool kit wrench that came with the car
Forum: Early V8 (1932-53) 02-14-2020, 05:11 PM
Replies: 13
Views: 588
Posted By Kurt in NJ
Re: Blast media

Try crushed glass, also limit the pressure to under 50lbs pressure
Forum: Early V8 (1932-53) 02-14-2020, 04:35 PM
Replies: 19
Views: 855
Posted By Kurt in NJ
Re: 6 Volt dim headlights

Measure the voltage at the bulbs, compare to battery voltage--- it won't matter what bulbs you have in the electricity is not getting there

A 6 volt car (Packard)that I work on came with every...
Forum: Model A (1928-31) 02-13-2020, 05:45 PM
Replies: 6
Views: 252
Posted By Kurt in NJ
Re: REbuild Early Vacuum Wiper

I have 3 of them apart, the pot metal has blisters inside, and the covers are warped to where a new gasket won't seal, and the shaft is worn so it is only tight without gaskets--- got a 4th to take...
Forum: Model A (1928-31) 02-13-2020, 03:25 PM
Replies: 12
Views: 622
Posted By Kurt in NJ
Re: New to the forum and questions (lot!)

The clip looks just like a glass to headlight housing or fog light clip on old Mercedes
Forum: Model A (1928-31) 02-13-2020, 02:50 PM
Replies: 16
Views: 548
Posted By Kurt in NJ
Re: Half of a cotter pin in oil pan?

If the cotter pins are not cinched tight they will rattle and wear through
Forum: Model A (1928-31) 02-13-2020, 02:48 PM
Replies: 6
Views: 238
Posted By Kurt in NJ
Re: Grounding Problems Cause By Frame Painting?

I cleaned the boss to bare metal, then tinned it with solder-- been trouble free for 45 years. Had some trouble with headlights grounding-- found some new lock washers with ridges that cut through...
Forum: Model A (1928-31) 02-13-2020, 09:25 AM
Replies: 9
Views: 444
Posted By Kurt in NJ
Re: Removing rear end, while leaving torque tube

first get the shaft through the seal without damaging it---then through speedo hole get bearing in place then push shaft in further, fit thrust washer align speedo drive gear on splines push a little...
Forum: Model A (1928-31) 02-13-2020, 08:24 AM
Replies: 9
Views: 444
Posted By Kurt in NJ
Re: Removing rear end, while leaving torque tube

You could release the snap ring through the speedometer gear hole—- and it will slide out, but that will just get it apart, to put it together I doubt you could easily get get all the pieces to line...
Forum: Model A (1928-31) 02-06-2020, 05:40 PM
Replies: 28
Views: 1,758
Posted By Kurt in NJ
Re: “Do not use a file” to dress down breaker points

It can chip the contacts--- i use a diamond knife sharpener
Forum: Model A (1928-31) 02-04-2020, 04:43 PM
Replies: 8
Views: 433
Posted By Kurt in NJ
Re: Points Cam ?

Both sides of the ramp look the same on A cam, one side taperes off on the B cam
Forum: Model A (1928-31) 02-02-2020, 12:27 PM
Replies: 16
Views: 743
Posted By Kurt in NJ
Re: 6 volt battery

I bought a optima from speedway it came in the mail in 2 days, free shipping, last optima lasted me 16 years
Forum: Early V8 (1932-53) 02-02-2020, 12:29 AM
Replies: 16
Views: 852
Posted By Kurt in NJ
Re: Is this junk

Shoe shine it some with fine emory paper and measure it
Forum: Early V8 (1932-53) 01-31-2020, 07:41 PM
Replies: 7
Views: 402
Posted By Kurt in NJ
Re: French 17 stud oil and water pumps

The oil pump is the main bearing cap---- just the gears are replaced, you would have to measure them to see if the same as American 60hp, the drive gear is hard to find in USA, I have found them but...
Forum: Model A (1928-31) 01-31-2020, 06:34 PM
Replies: 21
Views: 789
Posted By Kurt in NJ
Re: Pressure plate finger adjust

I would consider a new pressure plate that needs adjustments before use defective ---- it is something the factory sets up, but it seems a common obsession here with the model A and v8 people on this...
Forum: Early V8 (1932-53) 01-30-2020, 07:06 PM
Replies: 31
Views: 785
Posted By Kurt in NJ
Re: 6 volt/12 volt jump box

Use the handcrank in tool kit
Forum: Model A (1928-31) 01-30-2020, 07:00 PM
Replies: 23
Views: 912
Posted By Kurt in NJ
Re: Bearing fit ... engine oil gravity feed

The original bearings hold a lot of oil--- even years later there is enough in them to drip when taking apart ---
Forum: Model A (1928-31) 01-29-2020, 06:01 PM
Replies: 8
Views: 502
Posted By Kurt in NJ
Re: Model B one piece cast steel fan blade

Have to look for seam on back side, it's not cast
Forum: Model A (1928-31) 01-29-2020, 05:57 PM
Replies: 16
Views: 694
Posted By Kurt in NJ
Re: Cold Weather Shifting

Below freezing it takes some effort to move the shifter, steady pressure instead of forcing, then I go a block or two in first, after that I drive normally---(shell Omaha 680 gear oil)--- in the...
Forum: Early V8 (1932-53) 01-28-2020, 04:02 PM
Replies: 34
Views: 949
Posted By Kurt in NJ
Re: Installing replacement pistons

Ever since I read the replacement ring set instructions that said honing is not necessary if there is no bore damage I don't hone, --- even experimenting with putting used rings from another engine...
Forum: Model A (1928-31) 01-27-2020, 09:41 AM
Replies: 22
Views: 1,377
Posted By Kurt in NJ
Re: Rear backing plates delima

---do the shoes look centered on the backing plate visually -----if the drum is held in place can you work a feeler gauge in around the edge of the shoes---if they are off center you should be able...
Forum: Early V8 (1932-53) 01-25-2020, 02:36 PM
Replies: 3
Views: 279
Posted By Kurt in NJ
Re: helmet distributor air gap?

In a 30s radio installation book it said ( for reasons of radio interference), build up or move contacts to get 0.005 gap

A larger gap increases firing voltage for the spark plugs, a larger rotor...
Forum: Model A (1928-31) 01-24-2020, 11:29 PM
Replies: 30
Views: 1,191
Posted By Kurt in NJ
Re: Exhaust port crack.... need help!

use some head gasket in a jar---I have seen the results on engines with blown head gaskets, seen it make 1/2 inch of missing gasket
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 11:47 AM.