Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 93
Search took 0.01 seconds.
Search: Posts Made By: 34 FORDOR
Forum: Early V8 (1932-53) 01-06-2021, 12:58 PM
Replies: 3
Views: 492
Posted By 34 FORDOR
Re: 34 front fender , rear brace.

David , thank you for your reply
Forum: Early V8 (1932-53) 01-05-2021, 06:28 PM
Replies: 3
Views: 492
Posted By 34 FORDOR
34 front fender , rear brace.

Hi , I have 1 brace with the inner end bolted to the chassis , on the other side of car it is mounted up higher where the main fender and inner fender join.
Which is correct ? Photos ?
Forum: Early V8 (1932-53) 09-03-2020, 07:38 PM
Replies: 4
Views: 426
Posted By 34 FORDOR
Re: 34 rear hub bolts

Thanks for your replies, have reused some good ones.used Locktite to hold them because the shoulder had been removed to get them out . Will try and obtain some nos B1118 or 48 1118 . Lead foot...
Forum: Early V8 (1932-53) 08-27-2020, 02:29 PM
Replies: 4
Views: 426
Posted By 34 FORDOR
34 rear hub bolts

I need some rear hub bolts fo my 34 . My local supplier has sent me bolts listed as suitable for1928 to 1935 , they are approx 1/4 shorter than my originals ( 1 5/8 ) . I have checked online with...
Forum: Early V8 (1932-53) 11-03-2019, 11:14 PM
Replies: 10
Views: 976
Posted By 34 FORDOR
Re: Drum / hub retainer

Other side all done . Took it for a drive , slight contact on one side , had to remove it and give it a touch up with the angle grinder. All good now. I think these retainers should be mandatory...
Forum: Early V8 (1932-53) 11-03-2019, 07:09 PM
Replies: 10
Views: 976
Posted By 34 FORDOR
Re: Drum / hub retainer

One side done , one to go , then the Model A
Forum: Early V8 (1932-53) 11-03-2019, 02:51 PM
Replies: 10
Views: 976
Posted By 34 FORDOR
Re: Drum / hub retainer

Thanks for you replies , Charlie yes I need to do my Model A as well , SUHRsc I like your idea , I donít have access to lathe at the moment , will definitely go that way in the future . I have...
Forum: Early V8 (1932-53) 11-01-2019, 11:52 PM
Replies: 10
Views: 976
Posted By 34 FORDOR
Drum / hub retainer

Hi guys Is any one making the old style weld / bolt on rear drum retainer . Iím running original brakes on a 34 ? .The little bolt on brackets wonít work . I guess I could make up some that...
Forum: Early V8 (1932-53) 05-05-2019, 08:08 PM
Replies: 19
Views: 2,254
Posted By 34 FORDOR
Re: Winton trip in the 33

Another good outback trip Lawrie, love the wide open spaces, hope the 33 runs well for you , yeah post some pics. Weíre driving from Perth via the Great central to Maroochydore in a few weeks ,...
Forum: Early V8 (1932-53) 08-19-2018, 04:29 AM
Replies: 32
Views: 3,985
Posted By 34 FORDOR
Re: Old ford out west

You’re living the dream Lawrie .We spotted the 35 remains a few weeks ago on a trip to Broome via Darwin , also had a look around the truck museum at Winton where there was several old flathead...
Forum: Early V8 (1932-53) 05-24-2018, 01:27 AM
Replies: 8
Views: 1,404
Posted By 34 FORDOR
Re: 21 Stud heads..different?

Hi Rob , The head on the left is a 77E with firing order cast on top .( English Ford Pilot , many of these were shipped to the US as replacements for the 37- 38 21 stud engines ) the one on the...
Forum: Early V8 05-22-2018, 05:28 PM
Replies: 0
Views: 449
Posted By 34 FORDOR
32 spare wheel carrier

Wanted 32 spare wheel carrier , any one in New Zealand or Australia have one?
Forum: Model A (1928-31) 11-14-2017, 01:11 PM
Replies: 31
Views: 8,311
Posted By 34 FORDOR
Re: Noisy metal timing gear cured by torsional damper

I have had a harmonics ' rattle ' in my engine around 1800 rpm when accelerating in top gear . The engine has a counterweight crank , lightened fly wheel and fully balanced , sits on fm mounts ....
Forum: Early V8 (1932-53) 12-30-2016, 05:06 PM
Replies: 45
Views: 6,929
Posted By 34 FORDOR
Re: Across the desert in the snow

Another great trip . Thanks for sharing
Forum: Model A (1928-31) 12-30-2016, 05:02 PM
Replies: 17
Views: 3,115
Posted By 34 FORDOR
Re: Stromberg 97

I have a 97 on my 30 Tudor , started out with no pump and had similar problems . The needle / float valve needed some pressure to open . I modified the valve , but still wasn't 100 per cent , so...
Forum: Early V8 (1932-53) 09-04-2016, 05:23 AM
Replies: 6
Views: 676
Posted By 34 FORDOR
Re: 34 Rear perch bushings

I have found the repo ones don't last long on a heavy car if it is a driver. Go for nos or use modern nylon ones like the hot rodders use
Forum: Model A (1928-31) 08-13-2016, 02:41 PM
Replies: 23
Views: 5,089
Posted By 34 FORDOR
Re: Pinion puller

updraft. Yeah taper locks work well. I use a smaller one on the steering shaft when pressing on a new worm .
Forum: Model A (1928-31) 08-12-2016, 03:38 AM
Replies: 23
Views: 5,089
Posted By 34 FORDOR
Re: Pinion puller

I recently had to remove a pinion and drive shaft to install an overdrive .The pinion and bearing was really tight , it had been loctited into the housing. I decided to make my own puller out of some...
Forum: Model A (1928-31) 07-20-2016, 02:33 AM
Replies: 15
Views: 2,286
Posted By 34 FORDOR
Re: Model B Carb balancing

Secrets of speed mag #4 April 2009 has a couple of pages by Dave Remmer with photos on how to do this. Kevin Pm sent
Forum: Early V8 (1932-53) 06-17-2016, 05:01 AM
Replies: 21
Views: 2,667
Posted By 34 FORDOR
Re: French block intake gasket mismatch.

I had the same problem. Took a little off the casket on one side and worked on the port on the other with the die grinder and cleaned it up with a flap wheel. I intend to make a new casket for the...
Forum: Model A (1928-31) 06-04-2016, 04:56 PM
Replies: 25
Views: 4,532
Posted By 34 FORDOR
Talking Re: shortened pitman arms

Derek 90mph ? Maybe on the salt but not on our roads. Welding pitman arms is a real no no over here. The new forged arms can be made to work for rhd . Good luck with the new rhd arms
Forum: Model A (1928-31) 06-04-2016, 01:42 AM
Replies: 25
Views: 4,532
Posted By 34 FORDOR
Thumbs up Re: shortened pitman arms

Derek you've got.Easy to cut your drag link , cut left and right threads and screw on an adjusting sleeve. Find the centre position in your steering box, mark your steering wheel at the top,then...
Forum: Model A (1928-31) 05-28-2016, 03:31 AM
Replies: 13
Views: 1,828
Posted By 34 FORDOR
Re: cam shaft centre line

Lawrie Have a look on Vince Falters site , ford garage.com. I know he has the center line measurements you need . Good luck
Forum: Model A (1928-31) 05-23-2016, 02:10 AM
Replies: 11
Views: 2,958
Posted By 34 FORDOR
Tiny Tach problems

I recently purchased 2 Tiny Tachs , one for my A and another for my flathead v8 . Does the pick up wire normally wrap around the coil wire or a plug wire. On the A , l put it on no4 plug wire and it...
Forum: Model A (1928-31) 05-07-2016, 02:46 AM
Replies: 10
Views: 1,574
Posted By 34 FORDOR
Re: Cool experience

Syncro909 I would love to see some photos of your trip
Showing results 1 to 25 of 93

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:31 PM.