Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 15 of 15
Search took 0.00 seconds.
Search: Posts Made By: A V8 Al
Forum: Early V8 (1932-53) 12-27-2018, 04:01 PM
Replies: 3
Views: 412
Posted By A V8 Al
1932-34 truck dashlight

Could someone tell me where the bulb socket bracket mounts. It has a single capture nut and the wire from the socket to light switch is 13" long and is 2" from the left side of the dashboard. ...
Forum: Early V8 (1932-53) 12-11-2018, 08:14 PM
Replies: 2
Views: 414
Posted By A V8 Al
Re: FN!!STtXx!! Window channels

Thanks for the input Karl. I bought the regulators from CG Parts listed as 1932-34 pickup truck. I need to replace the roller on the lift arm?
Forum: Early V8 (1932-53) 12-11-2018, 07:13 PM
Replies: 2
Views: 414
Posted By A V8 Al
FN!!STtXx!! Window channels

I replaced the (missing) door window channels and regulators on my 1933 T 1 1/2 truck. The regulators are Vintique and work ok (?); but the window channels I bought from Mac's a while back (...
Forum: Early V8 (1932-53) 12-04-2018, 08:23 PM
Replies: 4
Views: 341
Posted By A V8 Al
Re: Truck speedometer cable

Sorry about the omissions...the truck is a 1933 short wheel. Al
Forum: Early V8 (1932-53) 12-04-2018, 01:49 PM
Replies: 4
Views: 341
Posted By A V8 Al
Truck speedometer cable

Does anyone know of a source for a 1 1/2 ton truck speedometer cable? Any suggestions on how to solve this . Thanks all in advance, Al
Forum: Early V8 (1932-53) 11-30-2018, 06:50 PM
Replies: 1
Views: 328
Posted By A V8 Al
Door window regulator

Having a problem installing door windows in my 1933 ford truck. The stud on the end of the window regulator arm will not fit thru the hole and slot of the window glass channel. Also, the stud on the...
Forum: Early V8 (1932-53) 04-23-2018, 09:48 AM
Replies: 3
Views: 543
Posted By A V8 Al
speedo cable

Ford's ton and a half AA and BB need a long speedometer cable, over 100 inches. Does anybody know of a source or solution for a missing cable?
Forum: Early V8 (1932-53) 04-22-2018, 10:41 PM
Replies: 8
Views: 1,140
Posted By A V8 Al
Leaky block

i'm leaking coolant into the combustion chamber and crankcase of my '48 V8. Any cure?..or just keep driving it until? The leak is in the lifter valley around a lifter bore.
Forum: Early V8 05-25-2016, 04:07 PM
Replies: 0
Views: 376
Posted By A V8 Al
Bracket & level assembly (brake shaft)

Need the assembly that the brake rods tie into at the frame X on a 1935-36 Ford Pass & Comm. Part no. 48 2458. In good useable condition. Thanks, Al
Forum: Early V8 10-18-2015, 04:56 PM
Replies: 0
Views: 312
Posted By A V8 Al
1935 Pickup truck outside mirrors

Wanted: Looking for outside, hinge mounted mirrors, glass unimportant.
Forum: Early V8 10-18-2015, 04:53 PM
Replies: 0
Views: 382
Posted By A V8 Al
1933 Truck Hood

Wanted: A nice straight ,rust pit free hood for a 1933 truck. Thanks
Forum: Early V8 10-18-2015, 03:00 PM
Replies: 0
Views: 291
Posted By A V8 Al
Outside hinge mount mirror

Wanted: For 1 1/2 ton truck, outside hinge pin mounted mirror. I need one or two arms, the mirrors themselves are not important. Tnanks
Forum: Early V8 10-18-2015, 01:02 PM
Replies: 0
Views: 314
Posted By A V8 Al
Wanted

stake body for shortwheel base 1 1/2 ton Ford truck. New England area.
Forum: Late V8 (1954+) 09-13-2013, 04:39 PM
Replies: 1
Views: 850
Posted By A V8 Al
260 V8 choke heat tubes

The two choke heat tubes on my 260 V8 Falcon Sptrint have rotted and broken off at the point they enter the exhaust manifold. What is the best way to remove the remaining tube from the manifold. ...
Forum: Model A (1928-31) 06-29-2010, 07:47 PM
Replies: 3
Views: 1,154
Posted By A V8 Al
Rear Wheel bearing removal

Is there an easy way of removing the lock ring that holds the grease seal and bearing in the rear hub? Thanks all, Al
Showing results 1 to 15 of 15

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:44 PM.