Forum: Model A (1928-31)
08-18-2020, 06:56 PM
|
Replies: 9
Views: 2,088
|
Forum: Model A (1928-31)
04-24-2020, 08:30 PM
|
Replies: 35
Views: 5,850
Re: Insulation material
Try this one.
https://www.usenergyproducts.com/collections/super-shield-1-4-inch-solid-foil-reflective-foam-core-insulation
|
Forum: Model A (1928-31)
04-24-2020, 11:42 AM
|
Replies: 35
Views: 5,850
|
Forum: Model A (1928-31)
04-24-2020, 10:53 AM
|
Replies: 35
Views: 5,850
Re: Insulation material
That was my concern, that is why I used the product I used. If you cut it 1/8" larger the the vertical surface it will stay in place on its own. As you can see my only experience is with a CCPU, cars...
|
Forum: Model A (1928-31)
04-23-2020, 08:57 PM
|
Replies: 35
Views: 5,850
Re: Insulation material
It's not glued, just lies on top of the floorboards with the floor mat placed on it.
Don't be fooled by the glare from my LED light the firewall is a black ABS insulated panel....
|
Forum: Model A (1928-31)
04-23-2020, 08:15 PM
|
Replies: 35
Views: 5,850
|
Forum: Model A (1928-31)
04-23-2020, 08:03 PM
|
Replies: 35
Views: 5,850
Re: Insulation material
I just installed this last December from the belt line down. On the kick and door panels I cut the width just slightly wider than the opening. The floor laid nicely under the mat, surrounded the...
|
Forum: Model A (1928-31)
04-02-2020, 07:58 PM
|
Replies: 18
Views: 3,609
Re: Solo Motor Installation
I was just getting ready to cut four inches out of mine. I had to put a bunch of towels on my firewall getting the engine out. If you had to do it again would you go 14" or 15"?
Thanks
|
Forum: Model A (1928-31)
03-29-2020, 04:25 PM
|
Replies: 24
Views: 4,082
|
Forum: Model A (1928-31)
03-15-2020, 01:15 PM
|
Replies: 5
Views: 2,405
|
Forum: Model A (1928-31)
03-15-2020, 12:58 PM
|
Replies: 6
Views: 1,538
Re: GAZ intake valve
Fair enough, I was just double checking to make sure I didn't miss an opportunity that was right in front of me. Anyone who knows me knows that I say this all the time " I only have enough money to...
|
Forum: Model A (1928-31)
03-14-2020, 08:08 PM
|
Replies: 6
Views: 1,538
Re: GAZ intake valve
Jim,
This is the situation I find myself in. Two weeks ago I sent my block off to Rich at Antique Engine Restoration for inserts. He informed me that the GAZ block weighed approximately 35 lbs more...
|
Forum: Model A (1928-31)
03-13-2020, 11:37 AM
|
Replies: 6
Views: 1,538
GAZ intake valve
Question for the masses.
Has anyone had any experience putting a set of larger intake valves in a GAZ block?
Thanks
|
Forum: Model A (1928-31)
02-02-2020, 08:20 PM
|
Replies: 9
Views: 1,608
Re: CCPU interior.
Here are the pictures I spoke of earlier. The firewall is an insulated ABS unit from one of the vendors and is black not silver, don't mind the LED glare.
...
|
Forum: Model A (1928-31)
01-31-2020, 06:02 AM
|
Replies: 41
Views: 8,051
|
Forum: Model A (1928-31)
01-30-2020, 05:56 AM
|
Replies: 36
Views: 8,960
|
Forum: Model A (1928-31)
01-29-2020, 02:30 PM
|
Replies: 36
Views: 8,960
|
Forum: Model A (1928-31)
01-29-2020, 06:23 AM
|
Replies: 9
Views: 1,608
Re: CCPU interior.
Don't be fooled by any contact cement, if you want it to last this is what the pros use.
https://www.dap.com/dap-products-ph/weldwood-landau-top-trim-high-heat-resistant-contact-cement/
|
Forum: Model A (1928-31)
01-28-2020, 01:38 PM
|
Replies: 9
Views: 1,608
Re: CCPU interior.
I just installed this last week from the belt line down. On the kick and door panels I cut the width just slightly wider than the opening. The floor laid nicely under the mat, surrounded the exposed...
|
Forum: Model A (1928-31)
01-23-2020, 04:58 AM
|
Replies: 2
Views: 1,351
|
Forum: Model-A
01-22-2020, 01:28 PM
|
Replies: 0
Views: 869
|
Forum: Model A (1928-31)
01-22-2020, 12:25 PM
|
Replies: 2
Views: 1,351
Oil pan drain plug
Does anyone know the diameter and thread pitch of the oil pan drain plug?
Thanks
|
Forum: Model-A
12-09-2019, 01:20 PM
|
Replies: 0
Views: 2,510
|
Forum: Model A (1928-31)
12-03-2019, 12:51 PM
|
Replies: 22
Views: 3,943
Re: Primer for YOM plates
Just some food for thought specifically for North Carolina YOM plates, it may apply else where too. No where in the statute does it state YOM's have to be NC. I've been and will continue to run...
|
Forum: Model A (1928-31)
12-03-2019, 12:40 PM
|
Replies: 36
Views: 8,960
|